Question about 2006 Hyundai Sonata
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Hopefully this picture comes through, if not let me know and I can zoom in. Be sure to remove the auto tensioner, compress it slowly in a vice and put a pin through holding holes until the belt is mounted properly, replace it and pull the pin.
Posted on Mar 26, 2009
Here is a diagram of you timing marks good luck and thanks for using FIX YA . please leave me a feedback.http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/sonata/2004_hyundai_sonata_timing_belt_diagram_marks.htm
Posted on Mar 29, 2009
You didn't specify whether you have the (4) cylinder or the (6) cylinder engine..... I have a 2004 Hyundai Sonata 2.4L 4 cylinder and I just changed the spark plugs in it. I believe that the 2005 2.4L engine is the same. To locate and change the (4) spark plugs on a 2004 Hyundai 2.4L 4 cylinder engine: Remove the (4) 12mm bolts from the decorative plastic engine cover. Remove plastic cover from engine and place it off to the side out of your way. Standing in front of the car, the (4) spark plugs are located laterally (left to right) in the recessed area underneath where the plastic engine cover was removed. Note: This engine has (2) coils....They are located above spark plugs number (2) and (3) from left to right. Starting with the fist spark plug on the left: Remove the spark plug cable by pulling straight up on the insulated connector. Using a spark plug socket, remove the old spark plug and install a new one in it's place. To access the second spark plug from the left, remove the electrical connector and the spark plug cable wire from coil number (1) and then remove the (2) 12mm bolts that secure the coil to the engine. Spark plug number (2) is located directly under the coil. Lift the coil straight up removing the insulated connector from spark plug number (2). Using a spark plug socket, remove old spark and install a new one in it's place. Repeat same procedures for spark plugs number (3) and (4). Note: If you have the (6) cylinder engine, the front (3) sparks pluge are readilly accessible but in order to access the (3) rear spark plugs, you will have to remove the intake manifold
Posted on Jul 08, 2009
Depends somewhat if it's a front rotor or a rear rotor. The most common problem will be "corrosion" that's binding the two metal parts together. If you are not trying to reuse the rotor after turning (many are throwaways now adays) take a large hammer and bang the outer edge of the rotor. The vibration should cause the corrosion to break apart, and the rotor should pull away. If your planning on re-using the rotor after turning use a large rubber mallet.
The front rotors have about a 3/4 inch common surface between the rotor and the wheel hub. You may need to bang on the backside of the rotor as you slowly turn the rotor in order to cause the two parts to slide apart. It can be a slow process, but you should see some movement (but it must be even movement around the entire rotor. The back rotors have far less common surface and a few good waps should break the parts free.
Posted on Jul 13, 2009
Tips for a great answer:
Mar 08, 2013 | Hyundai Motor 1998 Sonata
May 04, 2010 | 2006 Hyundai Sonata
Apr 16, 2010 | Hyundai Motor 2004 Sonata
Sep 02, 2009 | Hyundai Motor 1998 Sonata
Mar 29, 2009 | Hyundai Motor 2004 Sonata
Mar 16, 2009 | 1996 Hyundai Sonata
Feb 07, 2009 | 1996 Hyundai Sonata
Jun 23, 2008 | Hyundai Motor 2002 Sonata
385 people viewed this question
Usually answered in minutes!