Question about 1990 Nissan Axxess

1 Answer

How does the drum come off? Is there a a spring that you have to release on the inside?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 107 Answers

I assume that you speak of a rear brake drum and no spring, just RUST so you have to back off the brake shoes a bit then hit the drum rather hard all around and look for movement like in its getting loose. Keep band and keep pulling it will come....eventualy. Just make that drum spins around if not keep backing off on the brake shoe because they can hold the drum in place

Posted on Sep 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i find out if break spring is broken inside?


if a brake spring has broken in a drum then there will be a rattling noise or that drum will be overheating from dragging brake shoes
pull the drum and check

May 07, 2015 | Cars & Trucks

1 Answer

I have a2002 silverado emergency pedal activates like it should but when you release it the pedal comes back slow and not all the way is there a spring on the pedal assembley for the return of pedal


They're located at the rear brakes. If you have drums they're on the inside. You can add one. About midway under the truck, drivers side. You will see where the front cable connects to the rear. Add a spring here going back to the rear . Mount it to the frame somewhere.

Aug 31, 2014 | 2002 Chevrolet Silverado

1 Answer

HAND BRAKE RELEASESD CAR WILLNOT MOVE


Release hand brake. Pull it again. While feeling for the normal tension have an assistant listen at the rear wheels to see if the brakes are moving and releasing when you release the hand brake. Possible causes:
-binding or stuck cable
-broken parking brake handle ratchet mechanism
-seized calipers, or if drum brakes faulty drum brake hardware/springs

May 11, 2014 | 2005 Hyundai Elantra

1 Answer

How to remove and clean and replace the rear brakes on a 2008Toyota yaris


REMOVING REAR BRAKE DRUM SUB-ASSEMBLY
1. Release the parking brake and remove the rear
brake drum.
If the rear brake drum cannot be removed easily,
do the following:-
2.Remove the hole rubber and insert a screwdriver
through the hole into the backing plate, and hold the
automatic adjust lever away from the adjuster.
3.Using another screwdriver, contract the brake shoe
by turning the adjuster.
4. Take out the brake drum from the flange.
5. remove the shoe hold down spring cup, shoe hold down spring, pin and front side brake shoe.
6. Remove the tension spring. Remove the shoe return spring from the rear brake shoe and remove the parking brake shoe strut set.
7. Remove the shoe holding spring cup, shoe hold spring, pin and rear brake shoe.
8. separate the parking brake cable.
9. Remove the automatic adjust lever tension spring and remove the automatic adjust lever.
10. remove the C-washer and remove the parking brake shoe lever.
NOTE: Do not use any solvent like gasoline to wash the brake parts.
Always wear safety goggles and mask before using compressed air.



Dec 28, 2013 | Cars & Trucks

2 Answers

Rear brakes


Removal
1.Remove rear wheel and tire assembly from vehicle.

2.Remove rear brake drums from hub and bearing assemblies after loosening the two brake drum screws.
bj6c017a.gif
3.Be sure that the parking brake pedal is in the release(most upward) position.

4.Completely loosen square nut of the rear parking brake cable. Then create slack in the rear parking brake cables.
bj6c017b.gif
5.Remove adjuster spring from adjust lever and brake shoe.
bj6c017c.gif
6.Remove adjust lever and turn the adjusting wheel of adjuster assembly to the direction of the arrow as shown.
bj6c017d.gif
7.Remove the strut spring and the lower retracting spring from the brake shoe.
bj6c017e.gif
8.Remove the upper return spring from the brake shoe.
bj6c017f.gif
9.Remove brake back plate hold down spring and pin from the leading brake shoe assembly.

10.Remove the leading brake shoe. Then remove the adjuster assembly, strut and anchor spring from the trailing brake shoe.
bj6c017g.gif
11.Remove the trailing brake shoe from the brake back plate after removing hold down spring and pin.
bj6c017h.gif
12.Remove the trailing brake shoe from the rear parking cable.
bj6c017i.gif
13.Remove parking pivot lever from the leading brake shoe.
bj6c017j.gif
Replacement
1.Lubricate the eight shoe contact areas on the back plate and anchor.
bj6c017n.gif
2.Install the trailing brake shoe to the rear parking cable.

3.Install trailing brake shoe on brake back plate and install the trailing brake shoe hold down spring and pin on the brake shoe.

4.Tighten the square nut of rear parking cable.

5.Install the anchor spring then install adjuster assembly, and strut.

6.Install leading brake shoe on brake back plate.
bj6c017o.gif
7.Install the brake shoe upper return spring, strut spring and the lower retracting spring to the brake shoe.

8.Properly rotate the adjusting wheel of adjuster assembly to the direction of the arrow in as shown.
bj6c017d.gif
9.Install the adjuster spring on the adjust lever and leading brake shoe assembly.

10.Install the leading brake shoe hold down spring and pin on the brake shoe.
bj6c017q.gif
11.Adjust brake shoes assemblies so as not to interfere with brake drum installation.

12.Install the rear brake drums on the hubs.

13.Check and adjust whether the pedal stroke in the specification.(Refer to section BR Gr./On-vehicle service/Pedal stroke of parking brake)

14.Install wheel and tire.

15.Push the parking brake pedal to the floor once and release pedal. This will automatically remove the slack from and correctly adjust the parking brake cables.

16.Test the vehiche on the road. The adjust will continue the brake adjustment during the road test of vehicle.

Inspection
1.Inspect the disassembled parts for wear, rust or damage.

2.Measure the thickness of brake shoe lining.
Standard : 0.17 in (4.5 mm)
Minimum : 0.04 in (1 mm)

3.If the shoe lining is less than minimum or shows signs of uneven wear, replace new one.
bj6c017k.gif
4.Measure the inside diameter of the brake drum.
Standard : 10 in (254 mm)
Maximum : 10.07 in (256 mm)
bj6c017l.gif
5.If the inside diameter of the brake drum is more than maximum or shows signs of uneven wear, replace new one.

6.Inspect the lining and drum for proper contact. If the contact condition is improper, repair it with a grinder or replace the brake shoe assembly.
bj6c017m.gif

Aug 14, 2013 | 2002 Kia Sedona

2 Answers

Left rear drum brake locks up and releases on my 04 dodge neon


need to check your emergency cable its probably stuck

Feb 21, 2013 | 2004 Dodge Neon

1 Answer

How to remove rear drums


Hi M, Chock the front wheels and jack up the rear. Release the park brake and then tap around the drum with a hammer. Pull the drum towards you. If the drum is grooved inside it may catch on the shoes (liners).If there is access from the rear (which I doubt) back off the adjustment, if not it may mean damaging the springs and clips to remove. Regards John

Apr 28, 2012 | 2002 Honda Accord

1 Answer

How to change rear barke shoes


Brake Drums & Brake Shoes Removal & Installation To Remove:
Rear Drum Brakes kia-09-18-7627.gif

  1. Raise and safely support rear of vehicle.
  2. Release parking brake.
  3. Remove rear wheel assemblies. NOTE: If brake drum is stuck, install two 8 mm bolts into threaded holes and tighten evenly.
  4. Remove top return spring, front and rear shoe spring clips and hold-down pins.
  5. Remove anti-rattle spring and adjuster spring. NOTE: Note position of operating lever prior to removal.
  6. Remove bottom return spring.
  7. Remove clip and washer and detach parking brake cable from rear shoe.
  8. Remove brake shoes.
To Install:
  1. Lubricate all brake shoe contact points with appropriate grease.
  2. Place operating level into position on hub.
  3. Install rear brake shoe and connect parking brake cable to rear shoe with washer and clip.
  4. Install front brake shoe and install bottom return spring.
  5. Install hold-down pins and spring clips.
  6. Position operating lever and install top return spring.
  7. Install anti-rattle spring and adjuster spring.
  8. Install brake drum and screws.
  9. Adjust brakes and install rear wheel assemblies.
prev.gif next.gif

Jan 21, 2011 | 2003 Kia Spectra

1 Answer

I need to replace rear brakes for 2001 saturn


Your car came with 2 types of brakes for that year here is the DRUM BRAKE REMOVAL. I will have to send it in 2 posts since the text is too long to send it in 1 post. Please vote if this helps you:
  • Remove the wheels and brake drums.
  • Remove the lower return and adjuster springs using a universal brake spring remover. Do not over extend the springs or they will damaged and will need to be replaced.
  • Compress the leading brake shoe hold-down cup and spring while removing the pin from the rear of the backing plate. Release spring compression, then remove the hold-down cup and spring.
  • Apr 23, 2010 | 2001 Saturn SL

    1 Answer

    Left rear wheel will not turn at all and is locked on. The right rear is just dragging. The handbrake appears to have released normally. Car is a one year old small Chrysler - it belonds to a friend and is...


    Does the car have drums or disc brakes on the rear? If it has drums then the handbrake lever may not be releasing on the rear shoe itself or a spring or brake lining could have let go and got jammed. If the handbrake lever is the problem then removing the wheel and striking the drum with a large ball peen hammer should release it (may be barbaric but it works), this will not solve the problem the brakes would have to be removed and serviced or replaced depending on the problem. If the vehicle however has disc brakes on the rear then the caliper on that wheel may have become stuck or seized, normally they are replaced nowadays if this occurs since rebuild kits are not readily available. Still with disc brakes could also have stuck pad in its guide on the bracket, although much less likely, also tends to be less costly since you only have to remove and clean it up (rust, etc). If the handbrake is inside the rotor (internal drum), then you could have a problem with the shoes or lever releasing inside the rotor (depending on the setup on the rear). As well if it were not brakes in very, very rare occasions a wheel bearing could lock up, not very likely though. hope this will help you good luck

    Mar 01, 2010 | 1997 Dodge Neon

    Not finding what you are looking for?
    1990 Nissan Axxess Logo

    Related Topics:

    75 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    75197 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    14251 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...