Question about Suzuki Forenza

Open Question

THE AIR BAG LIGHT IS ON AND SHOWS A CODE OF B2502 PASS A/B OFF IND FAULT

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Volvo 850 fault codes

SRS reset

Posted on Aug 24, 2008

csmock132
  • 4669 Answers

SOURCE: Air bag light won't go off

It likely is a bad passenger air bag. Did you try switching it back to off on the switch,and unhooking the battery for 5 minutes.

Posted on May 30, 2009

SOURCE: My air bag light is on. What is the usual diagnosis?

For a smog inspection you can still pass if your air bag light is on. Its the check engine light that will fail you

Posted on Jul 15, 2009

  • 4844 Answers

SOURCE: Ford Mondeo Mk3 Estate 2L. Air bag / seat belt Warning Light

Common fault on FORD
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.


Just push it together properly and it should clear the AirBag fault


Posted on Sep 06, 2009

  • 401 Answers

SOURCE: fault codes b0026,b0043,b0044

you need to replace the SIR COIL

Posted on Nov 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 lincoln town car air bag light is on 5 beeps 5 times


The five beeps - five times would indicate a code 55 , but factory service info only goes to code 53 .

  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.

Did your air bag light flash at all ? Apparently this will do flash the air bag light codes as well .
Symptom Chart Condition Possible Sources Action
  • Air bag warning indicator is illuminated continuously
  • Fuse
  • Damaged wiring, terminals or connectors
  • A faulty diagnostic connector
  • A faulted RCM
  • A faulty instrument cluster
  • Go To Pinpoint Test A .
  • Air bag indicator flashing
  • Air bag/pretensioner supplemental restraint system (SRS) fault
  • REFER to DTC Priority Table.
  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.
  • No communication with the restraints control module (RCM)
  • Fuse
  • Diagnostic tool
  • Data link connector (DLC)
  • A faulted RCM
  • Circuitry
  • Go To Pinpoint Test V .
LFC - light flash codes .
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Table
DTC a LFC b Description Action To Take - Continuous The Air Bag Indicator is Illuminated Continuously, RCM Disconnected or Inoperative, Loss of Battery Feed, or Loss of Signal Ground Go To Pinpoint Test A . B1231 13 Crash Data Memory Full Install a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment . B1317 Continuous Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to Section 414-01 . B1318 Continuous Battery Voltage Low CHECK battery voltage; to be above 9.0 volts. REFER to Section 414-01 . B1342 12 RCM Is Faulted Install a new RCM. B1869 NONE
Continuous lamp
Secondary air bag warning sounds if another fault is present Lamp Air Bag Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test B . B1870 NONE
Secondary air bag warning sounds if another fault is present Air Bag Warning Indicator Circuit Short to Battery Go To Pinpoint Test C . B1891 53 Air Bag Tone Warning Indicator Circuit Short to Battery Go To Pinpoint Test D . B1892 53 Air Bag Tone Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test E . B1921 14 Air Bag Diagnostic Monitor Ground Circuit Open Go To Pinpoint Test F . B2292 33 Restraint System - Safety Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test G . B2292 34 Restraint System - Safety Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test G . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2294 24 Restraint System - Curtain Fault (Driver Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2294 25 Restraint System - Curtain Fault (Passenger Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2295 22 Restraint System - Side Air Bag Fault (Driver Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2295 23 Restraint System - Side Air Bag Fault (Passenger Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault (Front Impact Severity Sensor Circuit Fault) Go To Pinpoint Test K . B2296 43 Restraint System - Impact Sensor Fault (Driver Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 45 Restraint System - Impact Sensor Fault (Driver Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 44 Restraint System - Impact Sensor Fault (Passenger Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 46 Restraint System - Impact Sensor Fault (Passenger Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2434 51 Driver Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test L . B2435 51 Driver Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test M . B2438 52 Passenger Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test N . B2439 52 Passenger Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test O . B2477 Continuous Module Configuration Error INSTALL a new RCM. B2691 51 Driver Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test P . B2692 52 Passenger Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test Q . C1414 15 Incorrect Module Design Level Go To Pinpoint Test R . C1947 49 Driver Seat Track Position Sensor Circuit Short to Ground Go To Pinpoint Test S . C1948 49 Driver Seat Track Position Sensor Circuit Resistance Out Of Range Go To Pinpoint Test T . C1981 49 Driver Seat Track Position Sensor Circuit Fault Go To Pinpoint Test U . - - No Communication with the Restraints Control Module Go To Pinpoint Test V . Your best bet have codes checked with a scan tool .

Jan 23, 2017 | Lincoln Cars & Trucks

1 Answer

Code 64 for mazda b3000 2001? Its an air bag


should be the engine light blinking the code flash

paper clip trick on the diagnostic port
no information on 64

if you have an air bag fault needs the obd2 diagnostic reader
to locate the fault ,, fix ,, then reset the srs system

Oct 22, 2016 | Mazda Cars & Trucks

1 Answer

Porcshe air bag light on


The first step here and on any car with an air bag light is is to have the computer scanned to get codes out.
The computer will store a code when it detects a problem with the system, the code will help to locate what part of the air bag system has failed. for example there could be a code that reads b1234 pass/side buckle circuit fault, this code would tell us the problem is in the passenger side seat belt buckle, then with some testing the problem would be found. start by having the codes read, record and write back with codes , also including year,make ,model. good day

Oct 10, 2012 | 2000 Audi TT

1 Answer

Flashing airbag light 4 blinks 6 blinks


This is a code 46 LH Crash Sensor - Not Mounted to Vehicle Properly. Often there is a poor contact on one of the wiring connectors. Some of the problems can happen from a poor connection where everything connects under the drivers side seat.
Here is a list of codes for the airbag light issues.

Air Bag Fault Code Table

AIR BAG DIAGNOSTIC MONITOR FAULT CODE PRIORITY TABLE

Priority Code Component/Fault Description

Highest -- No Air Bag Lamp - Inoperative Lamp Circuit or No Ignition Voltage to Diagnostic Monitor

' -- Continuous Air Bag Lamp - Diagnostic Monitor Disconnected or Inoperative

' 12 Low Battery Voltage

' 13 Air Bag Circuit or Crash Sensor Circuit - Shorted to Ground

' 21 Safing Sensor - Not Mounted on Vehicle Properly

' 22 Safing Sensor Output Circuit - Shorted to Battery Voltage

' 23 Safing Sensor Input Feed/Return Circuit Open

' 24 Open in Circuit 944B or Low Resistance in Crash Sensor(s)

' 32 Driver Side Air Bag/Safing Sensor Circuit - High Resistance or Open

' 33 Pin 7 Not Grounded at Diagnostic Monitor

' 34 Driver Side Air Bag/Safing Sensor Circuit - Low Resistance or Shorted

' 35 Low Resistance Across Pins 8 and 9 at Diagnostic Monitor

' 41 Crash Sensor Circuit - High Resistance or Open

' 44 RH Crash Sensor - Not Mounted to Vehicle Properly

' 45 Center Radiator Crash Sensor - Not Mounted to Vehicle Properly

' 46 LH Crash Sensor - Not Mounted to Vehicle Properly

' 51 Diagnostic Monitor Internal Thermal Fuse - Blown and Short to Ground No Longer Exists

' 52 Backup Power Supply - Voltage Boost Fault

' 53 Internal Diagnostic Monitor Fault

Lowest -- Rapid Continuous Flashing of Air Bag Lamp - All Crash Sensors Disconnected

Hope this helps...

May 05, 2011 | 2003 Ford Escape

1 Answer

Abs light is stays on. The air bag light stays on as well. I have a 2004 Ford exploer sport trac 4x4


Get the fault code.

DTCa LFCb LFC Priority Description B1318 - - Ignition Voltage Below 9 Volts - - 1 RCM Disconnected, Inoperative, or Lost/Low Ignition Feed B1342 24 2 RCM is Faulted B1231 19 3 RCM Crash Data Memory Full B1921 21 4 RCM Bracket Ground Resistance High C1414 29 5 Incorrect Vehicle Identification Code B1887 15 6 Driver Air Bag Circuit Shorted to Ground B1916 15 7 Driver Air Bag Circuit Shorted to Battery or Ignition B1888 16 8 Passenger Air Bag Circuit Shorted to Ground B1925 16 9 Passenger Air Bag Circuit Shorted to Battery or Ignition B1932 32 10 Driver Air Bag Circuit Resistance High B1933 33 11 Passenger Air Bag Circuit Resistance High B1934 34 12 Driver Air Bag Circuit Resistance Low B1935 35 13 Passenger Air Bag Circuit Resistance Low B1901 14 14 Front External Crash Sensor Shorted to Ground B1941 41 15 Front External Crash Sensor Open Circuit or Short to Battery B2444 48 16 Driver Side Crash Sensor Internal Fault B2445 49 17 Passenger Side Crash Sensor Internal Fault B2441 42 18 Driver Side Crash Sensor Mounting Fault B2440 43 19 Passenger Side Crash Sensor Mounting Fault U2017 44 20 Driver Side Crash Sensor Communication Fault U2018 45 21 Passenger Side Crash Sensor Communication Fault B1993 36 22 Driver Side Air Bag Circuit Shorted to Ground B1992 36 24 Driver Side Air Bag Circuit Shorted to Battery or Ignition B1994 36 26 Driver Side Air Bag Circuit Resistance High B1995 36 28 Driver Side Air Bag Circuit Resistance Low B1997 37 23 Passenger Side Air Bag Circuit Shorted to Ground B1996 37 25 Passenger Side Air Bag Circuit Shorted to Battery or Ignition B1998 37 27 Passenger Side Air Bag Circuit Resistance High B1999 37 29 Passenger Side Air Bag Circuit Resistance Low B1892 - 30 Air Bag Tone Warning Indicator Circuit Shorted to Ground or Open B1891 - 31 Air Bag Tone Warning Indicator Circuit Shorted to Battery or Ignition B1869 Tonec 32 Air Bag Indicator Inoperative B1870 Tonec 33 Air Bag Indicator Shorted to Battery - - - No Communication With the Restraints Control Module (RCM)
a DTC: Diagnostic trouble code
b LFC: Lamp fault code, flashed on air bag indicator.

Apr 21, 2011 | 2004 Ford Explorer

1 Answer

MY AIR BAG LIGHT IS STAYING ON AND SOMETIMES IT FLASHES?


You need to find out what the fault code is. It will direct you to the area responsible.

Air Bag Diagnostic Monitor
ani_caut.gif WARNING: UNDER NO CIRCUMSTANCES SUBSTITUTE ANOTHER FUSE VALUE FOR THE 10A BATTERY FUSE. ANY FUSE OTHER THAN 10A MAY CAUSE DISARMING FAILURE AND MAY RESULT IN DANGER TO THE OCCUPANTS OF THE VEHICLE. DO NOT ATTEMPT TO REPLACE THE 10A BATTERY FUSE UNTIL THE AIR BAG SYSTEM FIRST HAS BEEN DEACTIVATED (SEE DEACTIVATION PROCEDURE FOR DETAILS).
NOTE: The safing sensor is internal to the air bag diagnostic monitor (14B056) and is not replaced separately.
The air bag diagnostic monitor continually monitors all supplemental air bag restraint system (SRS) components and wiring connections for possible faults in the system. If the air bag diagnostic monitor detects a fault in the SRS when the ignition switch (11572) is in the RUN position, a diagnostic trouble code (DTC) will be displayed by the air bag indicator, located on the instrument cluster (10849).
The air bag diagnostic monitor does not deploy the air bag in the event of a collision. The LH or RH air bag sensor and the safing sensor determine when to deploy the air bag.
The air bag diagnostic monitor illuminates the air bag indicator for approximately six seconds when the ignition switch is in the RUN position and then turns the indicator off. This shows that the air bag indicator is operational. If the air bag indicator does not illuminate or the indicator stays on or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
DTCs may not be displayed for approximately 30 seconds after the ignition switch is placed in the RUN position. This is the amount of time the air bag diagnostic monitor requires to perform all tests and verify system faults.
Each DTC (a series of flashes and pauses of the air bag indicator):
  • Represents a two-digit number.
  • Is always displayed at least twice.
If the diagnostic monitor detects a fault in the air bag system, a DTC will be written to the diagnostic monitors non-volatile RAM (NVRAM). This DTC will then cause the lamp to flash a lamp fault code (LFC) on the air bag indicator and can be retrieved with the New Generation STAR (NGS) Tester. After repair, the DTC may then be cleared from the NVRAM.
If a system fault is present and the air bag indicator is malfunctioning, an audible tone will be heard. The tone is a series of five sets of five beeps. If the tone is heard, the air bag system requires repair.
If a fault exists that makes unwanted air bag deployment possible, the air bag diagnostic monitor will attempt to remove deployment power by turning on a solid state switch to blow the 10A battery fuse 2.
If the 10A battery fuse has successfully been blown by the air bag diagnostic monitor, the air bag diagnostic monitor will not attempt to blow it again until the proper fault has been repaired and cleared (see Diagnostic Trouble Code Clearing procedures for details). The air bag diagnostic monitor will store both the unwanted deployment DTC and the loss of deployment power DTC. The loss of deployment power DTC is the highest priority.
DTCs are prioritized numerically. If two or more faults occur at the same time, the fault having the highest priority will be displayed first. After that fault has been corrected, the next highest priority fault will be displayed.
The air bag diagnostic monitor includes an internal backup power supply. This feature provides sufficient backup power to deploy the air bag in the event the battery (10655) or battery cables are damaged in a collision before safing and air bag sensors close. The backup power supply will deplete its stored energy approximately one minute after the positive battery cable is disconnected.
--------------------------------------------
The DTCs can be retrieved with New Generation STAR (NGS) Tester using the Retrieve/Clear Continuous DTCs option. Any DTCs stored in the air bag diagnostic monitor will be displayed on the NGS along with a brief description of the DTC. If no DTCs are present, the NGS Tester will display a SYSTEM PASSED message. This option can also be used to clear DTCs from the air bag diagnostic monitor memory, as long as the concern no longer exists. Once a DTC is logged into the air bag diagnostic monitor memory, it will stay in memory until 255 key cycles have been recorded or until the NGS is used to erase the DTCs. Once 256 key cycles have been recorded since the concern was last detected, the DTC will automatically be removed from memory.

Jan 18, 2011 | 1997 Ford Expedition

2 Answers

My 2003 ford expo has a constant airbag light lit after starting the veh. I have a new sensor, can't figure out were 2put it.. Please help.


first, you need to read the Lamp Fault Code, LFC from the flashing light. Here's how:

Lamp Fault Codes
When the restraints control module (RCM) detects a system fault, it will cause the air bag indicator to flash a coded sequence: a lamp fault code (LFC). The code is two digits. The first digit is flashed with a 0.5 second interval between pulses. There is a 2 second pause before the second digit is flashed, which also has a 0.5 second interval between pulses. There is a 5 second pause between each display of an LFC.
Each LFC is flashed five times after which the air bag indictor will remain lit for the remainder of the key-on cycle. If there are multiple LFCs, each LFC will flash in order of priority.
-------------------------------------------------------
The fault could be in the air bag circuits, the canopy circuits, the pretensioner circuit on the seat belts, etc.
Report back with code.

here's some of system.

SECTION 501-20B: Supplemental Restraint System 2003 Expedition/Navigator Workshop Manual
DESCRIPTION AND OPERATION Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants in addition to that provided by the three-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles can also be equipped with optional safety canopies that deploy from the A-pillar to the C-pillar upon a side impact or if a rollover condition is detected. If equipped with safety canopies, a unique restraints control module (RCM) is used.
See the following illustration for deployable component location.
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) Deployable Components a55c8c5.gif Item Part Number Description 1 611D10 Passenger air bag module 2 042D94 Passenger side safety canopy module 3 042D95 Driver side safety canopy module 4 61203 Driver safety belt buckle and pretensioner 5 043B13 Driver air bag module 6 14A664 Clockspring 7 61202 Passenger safety belt buckle and pretensioner

4ee7996.gif
Item Part Number Description 1 14B321 Restraints control module (RCM) 2 14B345 Second row, C-pillar side impact sensor 3 14B345 Second row, C-pillar side impact sensor 4 14B416 Driver seat track position sensor 5 14B345 Front row, driver door, side impact sensor 6 14B006 Front impact severity sensor 7 14B345 Front row, passenger door, side impact sensor

Apr 23, 2009 | 1997 Ford Expedition

1 Answer

Flashing airbag light


yes, go here for more help. There is a file on how to download codes and clear system.

The number of flashes is giving you a lamp fault code, LFC. What is it giving you?

http://autos.groups.yahoo.com/group/villagerquest/

Diagnostic Test Modes Without Scan Tool
Two mode options are available under the diagnostic test modes:
  • user mode.
  • diagnosis mode.
The ignition switch is used to alternate from one mode to another.
Diagnosis Mode
The diagnosis mode will display any fault present in the system. The SRS will not enter diagnosis mode if no malfunction is detected.
User Mode to Diagnosis Mode
NOTE: The SRS will not enter diagnosis mode if no fault is detected in user mode.
  1. Ignition switch to ON.
  1. After the air bag warning indicator lights for seven seconds, set ignition switch to OFF within one second.
  1. Wait more than three seconds.
  1. Repeat steps 1 through 3 three times.
  1. Ignition switch to ON.
Diagnosis Mode to User Mode — After Repair
  1. Ignition switch to OFF for at least one second.
  1. Ignition switch to ON.
Diagnosis Mode to User Mode — During Diagnosis
NOTE: If switch from Diagnosis Mode to User Mode is required while diagnosing a fault, carry out the following procedure.
  1. Ignition switch to ON.
  1. After the air bag warning indicator lights for seven seconds, set ignition switch to OFF within one second.
  1. Wait more than three seconds.
  1. Repeat steps 1 through 3 three times.
  1. Ignition switch to ON.
Clearing Lamp Fault Codes
NOTE: Lamp fault codes must be cleared from memory before proving out the system.
NOTE: When a new RCM is installed, the air bag warning indicator will operate in user mode. Switching to diagnosis mode is not required.
To clear lamp fault codes after a repair, carry out the procedure to switch from diagnosis mode to user mode. Once in the user mode, the lamp fault codes will be cleared from memory.
Lamp Fault Codes
If the air bag diagnostic monitor detects a current fault, the fault code will be displayed with a flashing sequence of the air bag indicator. The fault code consists of:
  • A start signal to indicate the beginning of a fault code.
  • A number of flashes indicating the particular code that has been set.
The start signal:
  • begins with two seconds off.
  • two seconds on.
  • off.
  • one second on.
  • two seconds off.
Following the start signal, if any current fault is detected, the fault code will be displayed. The fault code:
  • is a series of half second flashes of the air bag indicator.
  • is followed by the start signal.
The start signal and the code for any current fault will repeat until the ignition is switched off or the air bag diagnostic monitor is switched to the user mode.
Inspection and Verification
  1. Verify the customer concern by checking the air bag indicator in the instrument cluster. Refer to Prove Out in this section.
  1. Visually inspect for obvious signs of mechanical and electrical damage using the following chart.


Visual Inspection Chart Mechanical Electrical
  • Damaged air bag diagnostic monitor bracket
  • Open fuse
  • Damaged wiring harness
  • Loose or corroded connectors
  • Circuitry open or shorted
  • Damaged shorting bars

  1. If the concern is not visually evident, enter the system Diagnosis Mode.
  1. If no DTCs are displayed in the Diagnosis Mode, proceed to the Symptom Chart in this section.
  1. If DTCs are retrieved, proceed to the Air Bag Diagnostic Monitor Fault Code Table in this section.


Air Bag Diagnostic Monitor Fault Code Table Code Component/Fault Description 0 Normal Operation/No Fault Detected 1 Front Passenger Safety Belt Pretensioner 2 Driver Air Bag Module Circuit Is Faulted 3 Front Driver Safety Belt Pretensioner 7 Air Bag Diagnostic Monitor Fault 8 Passenger Air Bag Module Circuit Fault 9 Low Battery Voltage

Mar 24, 2009 | 2001 Mercury Villager

1 Answer

Instrument Panel Codes??


Yes, it's called a lamp fault code.

9 is not familiar to me. Call dealer service department and ask them what code means.

Here are codes for a 94 Aerostar. I don't have 91 Sable. Sorry.



Air Bag Diagnostic Monitor Diagnostic Trouble Code Priority Table Diagnostic Trouble Code Component/Fault Description — No Air Bag Indicator — Inoperative Indicator Circuit or No Battery Positive Voltage to Air Bag Diagnostic Monitor — Continuous Air Bag Indicator — Air Bag Diagnostic Monitor Disconnected or Inoperative 12 Low Battery Voltage 13 Air Bag Module or RH Cowl Side Panel Air Bag Sensor Circuit Shorted to Ground 21 LH Cowl Side Panel Air Bag Sensor Not Mounted to Vehicle Properly 22 LH Cowl Side Panel Air Bag Sensor Circuit Shorted to Battery Voltage 23 LH Cowl Side Panel Air Bag Sensor Circuit Input Feed/Return Circuit Open 24 LH Cowl Side Panel Air Bag Sensor Diagnostic Circuit Open or Low Resistance in Center Air Bag or Front Air Bag 32 Driver Side Air Bag Circuit High Resistance or Open 33 Passenger Side Air Bag Circuit High Resistance or Open 34 Driver Side Air Bag Circuit Low Resistance or Shorted 35 Passenger Side Air Bag Circuit Low Resistance or Shorted 41 Center Radiator and RH Cowl Side Panel Air Bag Sensor Circuits High Resistance or Open 44 RH Cowl Side Panel Air Bag Sensor Not Mounted to Vehicle Properly 45 Center Air Bag Sensor Not Mounted to Vehicle Properly 46 Open Splice Center Air Bag Sensor Ground Monitor 51 Air Bag Diagnostic Monitor Internal Thermal Fuse Blown and Short to Ground No Longer Exists 52 Backup Power Supply Voltage Boost Fault 53 Sensor Circuits Resistance to Ground or Internal Air Bag Diagnostic Monitor Fault — Rapid Continuous Flashing of Air Bag Indicator

Feb 25, 2009 | 1992 Mercury Sable

1 Answer

Airbag flashes 10 times misses a flash then repeats


Try clearing the codes & see if it returns. I do not see a code fault 10. Starts at 12.

---------------------------------------------------------------------
Section 01-20B: Restraints, Passive — Supplemental Air Bag System 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual DIAGNOSIS AND TESTING Diagnostic Trouble Code Clearing Procedure to Clear Diagnostic Trouble Codes from Diagnostic Monitor Non-Volatile Random Access Memory.
Normal Operation
The air bag diagnostic monitor (14B056) continually checks the air bag system for readiness. When a fault condition is detected, the DTC associated with that fault is stored in the air bag diagnostic monitor's Non-Volatile Random Access Memory (NVRAM). After writing the DTC to NVRAM, the air bag diagnostic monitor signals the fault by flashing the appropriate diagnostic trouble code on the air bag indicator. The diagnostic trouble code written to NVRAM is permanently stored in the air bag diagnostic monitor until cleared by the diagnostic trouble code clearing procedure.
  • Upon each cycle of the ignition switch (11572) , the air bag diagnostic monitor checks for diagnostic trouble codes written in NVRAM. If any diagnostic trouble codes exist in NVRAM, the air bag diagnostic monitor will then check to see if these fault conditions are still present.
  • If the conditions of the diagnostic trouble code in NVRAM are still present, then the air bag diagnostic monitor will use the air bag indicator to flash out the diagnostic trouble code number that was written in memory.
  • If the conditions of the diagnostic trouble code are not still present (indicating an intermittent or serviced fault), the air bag diagnostic monitor will use the air bag indicator to flash out a DTC which is the sum of the diagnostic trouble code in NVRAM plus 40.
Example: Due to corrosion, high resistance develops on the driver side air bag circuit. The air bag diagnostic monitor stores a diagnostic trouble code 32 in NVRAM. Upon each cycle of the ignition switch , the air bag diagnostic monitor checks the resistance of the driver air bag circuit.
  • If the resistance is still high, the air bag diagnostic monitor causes the air bag indicator to flash out a DTC 32.
  • If the resistance falls within the normal range due to service or an intermittent condition, the air bag diagnostic monitor causes DTC 72 to be flashed on the air bag indicator.
Once a fault has been serviced, the associated diagnostic trouble code may be cleared from NVRAM. Only diagnostic trouble codes that the air bag diagnostic monitor sees as repaired or intermittent may be cleared (diagnostic trouble codes 52 and above). In no circumstances can hard fault conditions (diagnostic trouble codes 45 and below) be cleared.
  1. Follow the diagnostic procedures as outlined to service the fault condition flashing on the air bag indicator.
  1. Cycle the ignition switch to OFF and then to RUN.
  1. Observe air bag indicator prove-out (six ± two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.
  1. Locate the Diagnostic "Trouble Code Clear" Connector located underneath the glove compartment (06010) containing Circuits 631 (T/R) and 57 (BK).
  1. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.
  1. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).
  1. Release short on Circuit 631 (TAN/RED STRIPE) to Circuit 57 (BLACK). This short must be released within 25 seconds after the diagnostic monitor tone sounds. Diagnostic trouble code is now cleared from NVRAM. Next highest priority diagnostic trouble code stored in NVRAM (if one exists) will begin flashing.

Feb 09, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

550 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...