Question about 2005 Chrysler PT Cruiser

1 Answer

How do I replace a 2005 pt cruiser camshaft sensor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Camshaft sensor sit in the end of the cylinder head, drives side, just unscrew both little bolt's from sensor, remove sensor, and install new cam sensor, no reprogramming needs to be done.

Posted on Sep 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo


P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Dec 14, 2011 | 2005 Chrysler PT Cruiser

1 Answer

Labor involved tn replacing camshaft sensor on a 2005 pt cruiser


The cam sensor is very easy to change. The hardest part is getting stuff out of the way so you can see it. It is located on the back (driver's side) of the cylinder head directly above the transmission bell housing and has two 8mm-head bolts in it. It looks like the picture below.


dttech_29.jpg

Jun 13, 2011 | 2005 Chrysler PT Cruiser

1 Answer

2002 PT Cruiser. Vehicle shut down while driving. Received P0340 Trouble code..No camshaft position sensor signal at pcm. I replaced Position Camshaft Sensor, book suggests life on these 5-10 years, It...


This could be related to a loose camshaft drive belt. If you have slack in the belt the camshaft will rebound on over run causing the P0340. It can also be a Crackshaft sensor problem too.(P0335) Hope this helps...

Mar 06, 2011 | 2003 Chrysler PT Cruiser

1 Answer

Changed the timing belt and camshaft sensor on a 2005 pt crusier pretty sure its timed correctly because the car seems to run fine and revs high with no problems although it still throws P0016 code even...


What the P0016 code means. P0016 is the OBD-II generic code indicating that the camshaft position sensor for bank 1 does not correlate to the signal from the crankshaft position sensor. The camshaft timing is out of position due to the timing chain jumped teeth. The camshaft phaser is out of position due to problems with phaser.

May 22, 2017 | 2005 Chrysler PT Cruiser

2 Answers

2002 pt cruiser replaced camshaft position sensor still not starting wires are good


if you replace the crank sensor and camshaft sensor you need a DRB scan tool reprogram sensor to pcm.so they will work.

Dec 06, 2009 | 2002 Chrysler PT Cruiser

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...


P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

3 Answers

Code PO340


P0340 is a Crankshaft Position Sensor error. It determines firing order and is most likely the cause of your problem. It's mounted near the oil filter on the engine block. Below is a picture of how it appears in your car. Best of luck.
Greg


23ad084.gif

Jul 13, 2009 | 2005 Chrysler PT Cruiser

3 Answers

Code 344 camshaft sensor ciurcut intermitint 05 pt cruiser


im having exactly the same problem with a 2004 pt. took it to a dealer they told me ecm, replaced it and still the same problem. i changed out the cam knock sensor and the crank sensor. same thing. if i erase the code it will run perferct for an hour sometimes then same thing, light comes on and wont accelerate, over 2000 rpm. weird. im lost, it makes no sence.

Jun 03, 2009 | 2005 Chrysler PT Cruiser

1 Answer

2002 pt cruiser Camshaft Sensor


change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Feb 04, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

884 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...