Question about 1997 Ford Taurus

1 Answer

When I take off kind of quick it shimmies like maybe it is a motor support. Otherwise it does fine if I don't take off too quick and it runs and shifts fine.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 127 Answers

Hi, if oil seaps on to the engine mounting they will be sloppy. its an old girl now, and maybe the engine mountings are rough, if this is the case you need to change both. ask a mate to give it a rev, and look at the engine, it should only move at the start of the rev. if it is a blur. the engine mountings need replacing. the suspension can do the same thing. be pussing hard down on the wings and let go will test this. if the bounce lasts more than 3 then it is your suspension gerry

Posted on Sep 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My ac only blows hot air and wont take a charge


Quick test. Find the receiver drier there should be a sensor on it this is a pressure sensor the compressor will not cut in if low on gas cause the lubricant flows through the system with the gas. Unplug sensor & bridge the wires in the plug. With car running & A/C on your A/C clutch should now cut in. This will test the compressor & clutch but don't leave it bridged or you will destroy the compressor. Otherwise could be switch etc but start with that test. As for not accepting gas I don't know Blockage maybe? bad valve?

Jun 14, 2012 | Cars & Trucks

1 Answer

2002 ford escort zx2 troubleshooting guide


If you feel the pulsation in the wheel than its the front rotors that are likely warped. If you feel it in the seat than its the rear drums or rotors. If you don't feel it until you push on the brake pedal than it has to be in the brake system. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Jan 25, 2012 | 2002 Ford ZX2

2 Answers

I have a 2002 chev silverado 2500HD duramax 4x4, The truck starts only when given a shot of quick start in the airbox. After it runs great you can shut it off then re start it fine. It will not start...


You need new glow plugs. Im guessing you live somewhere kind of cold maybe. It starts just fine after running because the motor is already warm. Quick start will work.....or at least it did for me until I used one mornig and went to crank and BOOM. It blew my air filter case to pieces and caught the filter on fire. Starting fluid is not meant for diesel motors. If you cant afford new glow plugs what worked for me is turn on the key all the way but dont crank wait 10 sec then repeat a few times and it should crank unless its really cold out or the plugs are really bad. Trust me thats what it is. I replaced mine and now It cranks right up even when its super cold.

May 09, 2011 | 2002 Chevrolet Silverado 2500HD

2 Answers

Stalls when I put it in gear or come to a stop runs fine otherwise


you need to change your idle motor (iac valve) this controls the air that engine needs to mix with the fuel to run.simple to do yourself,two screws and one 2 wire plug.

Feb 01, 2010 | 2004 Ford F150

1 Answer

Engine stalls when stopping


It sounds like the torque converter clutch solenoid is bad.

Apr 02, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Shimmy in the front of my 2000 Lasabre


you more and likely need a front end aliagnment and your tie rod ends maybe worn out

Mar 15, 2009 | 2000 Buick LeSabre

2 Answers

Idle studder


a shimmy if you stomp on the gas and then let off quickly do you hear a large clunk if so prob a motor mount if the shimmy is a low idle engine loping or rpm up and down at low idle its prob the egr valve hope this helps

Mar 05, 2009 | 1990 Honda Civic

2 Answers

Sluggish on acceleration


sounds like ur injectors have them cleaned or run chevron with techron injector hope they are just dirty and not shorting out

Jun 07, 2008 | 1991 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1997 Ford Taurus Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...