Question about Datsun 210

1 Answer

What are the timing marks for a 200b datsun where do they sit and where dose the cam sit

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 127 Answers

Hi, normally the inlet vale of the camshaft (s) sticks up and to the right, this is the first valve No. 1. normally at the back of the camshaft there is a off set groove to aline it gerry

Posted on Sep 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ON THE CAM GEAR THERE IS A NO 1 2 AND 3 IN THE MIDDLE IS 3 HOLES SIZE 6 MM ON EACH HOLE WHICH HOLE MUST A USE. IN WHICHPOSITION MUST THE ROCKERS BEEN PLACED ON NO 1 CYLINDER


The three holes allow you to slightly advance the valve timing to compensate for stretch in the timing chain over time. If the chain is brand new then obviously you would be using hole number one. And by the time its ready to be replaced you should already be on hole number three. The repair manual should tell you all this though and you should not be doing this kind of work without a manual. For early Datsuns like the 240Z I've always found the Haynes manuals to be very good.

Sep 28, 2016 | Datsun Cars & Trucks

1 Answer

I changed the head gasket in my 82 nissan datsun 720 now it wont start has fire and gas getting to it how do i fix it


My guess is you have gotten the cam or ignition timing off during reassembly. datsun Series head replacement part 1
This video shows the proceedure. Watch it and see where you went wrong.

Apr 03, 2016 | Nissan Cars & Trucks

1 Answer

How do I go about sitting the timimg on a 94 ford ranger lt pickup


On the 4 cyl engine, you line up the crank pulley with the timing mark and the cam gear with the pointer on the timing cover.
On V6 engines the cam and crank gear dots point at each other. 6 oclock for the cam and 12 oclock for the crank.

Jun 16, 2015 | Ford Ranger Cars & Trucks

1 Answer

How to set timing on 1994 chrysler labaron 3.0


the valve springs are pushing against the cam lobes and turning the cam, you have to hold them with special tools or wrenches, usually the will stay in time if you hold them lined up with the marks and release gently on wrench, don't breath or they will jump

25005933-iv5yhqpktypbvunjtpsp2olz-4-0.gif

Aug 25, 2014 | 1994 Chrysler LeBaron

1 Answer

Replace timing belt on 2005 hyundai xg350 v6


When I did a timing chain on my Datsun I set up TDC on number 1 cylinder and then used a dob of paint on each pulley and a fixed point on the engine so that I could make sure everything lined up the same when I changed the chain.

Sep 17, 2017 | Hyundai XG350 Cars & Trucks

1 Answer

Installed new distributor and cant get the thing started getting spark at points but not at plugs


You probably have it out of time, when it hits the cam it twists around out of time, you have to make sure the rotor is pointing to No. 1 piston. when No 1 is up, TDC, and the timing mark on the front of the engine is on its mark. The rotor will twist down on the cam, you can put the cap on and follow the wire to number 1 , then make sure when it is seated, it is pointing to no 1. No 1 is the front most cylinder. Hope this helps.

Apr 25, 2011 | Datsun 510 Cars & Trucks

1 Answer

I'm replacing the timing chain on my 1984 nissan z24 and not sure about the timing marks or alignment on the cam and crank. How do I align them properly so I only do this once?


roll engine over till its tdc mark where the gear marks are youll be close may have to adjust distributer a bit to fine tune with timing light

Jan 17, 2011 | Datsun 720 Cars & Trucks

2 Answers

2001 pt cruiser broke timing belt


CHECK AUTO ZONE .COM FOR TIMING PROCEEDURE. I HAVE DONE THIS & IT IS VERY HARD TO GET TIMING MARKS PERFECTLY LINED UP. TOOK ABOUT 3 TRIES. ( CAMS WANT TO MOVE DURING PROCESS.) WHEN TIMING IS JUST RIGHT , IT WILL RUN. MAKE SURE BOTH CAM SROCKET ARROWS ARE POINTING UP. THERE IS A TIMING MARK IN THE VALLEY OF THE EXHAUST CAM SPROCKET TEETH THAT I MISSED.YOU HAVE TO START WITH EXHAUST CAM TIMING MARK JUST BELOW INTAKE CAM SPROCKET TIMING MARK & THEN WHEN BELT IS COMPLETELY ON , MOVE EXHAUST CAM TO TAKE UP SLACK IN BELT. IT WORKS !!!

Nov 28, 2008 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Datsun Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Datsun Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...