Question about Chrysler 300

Open Question

How to install idler pulley 2007 chrysler 300

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: Idler Pulley

Yes you do there is no way of removing it with out one with out wrecking it or damaging it

Posted on Jan 10, 2009

shop242
  • 214 Answers

SOURCE: I need to know how to install an idler pulley for a 1995 Saturn

Getting the belt off is the tuffest.. Thats all I can say lol

Posted on Mar 12, 2009

jturcotte
  • 7772 Answers

SOURCE: need a diagram for tensioner/idler

Please let me know if you have any questions, and thanks for using FixYa.
3.3L AND 3.8L ENGINES-SERPENTINE BELT

See Figure 12
The Poly-V drive belt is provided with a dynamic tensioner to maintain proper belt tension. To remove or install this belt:

  1. Raise the front of the vehicle and safely support on jackstands.
  2. Remove the right front splash shield.
  3. Release tension of the belt by rotating the tensioner assembly clockwise.
  4. While holding the tensioner in the rotated position, remove the belt from the various pulleys-make sure to note the route that the belt takes before removal.
  5. To install the belt, route it through the various pulleys except for the tensioner pulley. Once the belt is satisfactorily mounted on the pulleys, rotate the tensioner clockwise and slide the belt onto the tensioner pulley. Make certain that the belt is mounted so that the grooves in the belt are correctly aligned with the grooves in the pulleys.
jturcotte_1511.gif

Fig. Fig. 12: To remove the serpentine belt from the 3.3L and 3.8L engines, rotate the tensioner assembly clockwise

  1. Install the right front splash shield to the underside of the vehicle.
  2. Lower the vehicle back to the ground.
  3. Start the engine and allow to idle for a few minutes. Shut the engine off and double check the placement of the belt on the pulleys.

Posted on Apr 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HDo I remove and install an idler pulley on a 2005 Toyota Camry?


How to replace drive belt tensioner Toyota Camry - YouTube

? 4:26
https://www.youtube.com/watch?v=gfSJvN-CE2E
Feb 22, 2013 - Uploaded by Fix It Angel
2002 2003 2004 2005 2006 2007 2008 2009 Toyota Camry. Engine, 4 cylinder, 2.4L, 2AZ-FE. 2004 Toyota ...

Idler Pulley, How to replace (EASY and CHEAP) - YouTube

? 4:56
https://www.youtube.com/watch?v=axAltpW8wR4
Nov 2, 2013 - Uploaded by ChrisFix
Idler pulley squeak? Learn how to fix a squeaky pulley in your car. The serpentine belt in your car powers the ...

2007 Camry Serpentine Belt Replace - 4 Cyl, 2.4 liter ...

? 4:21
https://www.youtube.com/watch?v=ejhyCrh96a8
Jan 13, 2013 - Uploaded by Flyin Brian
I show you step-by step how to get the old belt off and install a new ... ... Water pump replacement 2007 Toyota ...


Jan 27, 2016 | Toyota Cars & Trucks

1 Answer

How do you remove Idler pulley?


usually fastened to motor with either a bolt that goes through the pulley/bracket into the motor, or a nut that fastens it to the motor. no special tools needed.

Sep 11, 2015 | 2006 Chrysler 300 Touring

2 Answers

Could you please tell me how to replace the air conditioner belt on a 2002 Chrysler 300M


  • On the lower front passenger side of the engine there is an adjustable idler pulley for the AC. Loosen that center bolt a few turns to release the tension on the AC belt.
  • Remove the old belt.
  • Place new belt on.
  • Tighten the idler pulley bolt until the belt is snug.
  • Job complete.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jun 14, 2011 | 2002 Chrysler 300M

3 Answers

Re install a serpentine belt on a 94 chrysler lebaron 3.0L


There should be a diagram attached to the car near where the belt goes showing how the belt is to run through the pulleys.
Newer vehicles have a tension pulley which is a pulley on a spring loaded arm that keeps the belt tight.

First run the belt on all the other pulleys and then use a wrench to hold the tension pulley back while you slip the belt on.

Older cars do not have a tension pulley and you had to usually loosen something like the alternator a little bit to get it on.

Mar 12, 2010 | 1994 Chrysler LeBaron

1 Answer

1999 Chrysler idler pulley reverse tread


They are standard, right to tighten and left to loosen. Good luck and be safe.

Dec 23, 2009 | 1995 Chrysler LeBaron

2 Answers

Where can i find a diagram to install serpentine


Most parts stores can print this out for you for free.

Sep 10, 2009 | 1991 Chrysler LeBaron

1 Answer

1996 Grand AM 3.1L serpentine belt replacement


Try this procedure.
0900823d8004ed44.jpg


To replace a worn belt, locate the idler or generator pulley.

0900823d8004ed45.jpg


Loosen the hold-down fastener for the idler or generator pulley.

0900823d8004ed46.jpg


Pry the idler or generator pulley inward to release the belt tension and remove the belt.

0900823d8004ed47.jpg


Match the old belt up for size with the new replacement belt.

0900823d8004ed48.jpg


Observe the belt routing diagram in the engine compartment.

0900823d8004ed49.jpg


Install the new belt over each of the drive pulleys. Often the manufacturer recommends a sequence for feeding the belt around the pulleys.

0900823d8004ed4a.jpg

Art courtesy of Delmar - Thomson Learning.
Pry out the idler or generator pulley to put tension on the belt.
Pry out the idler or generator pulley to put tension on the belt.

0900823d8004ed74.jpg


Install the belt squarely in the grooves of each pulley.

0900823d8004ed75.jpg


Before adjusting belt tension, check for proper pulley alignment. This is especially critical with serpentine belts. Measure the belt deflection in its longest span. If a belt tension gauge is available, use it and compare the tension to specifications.
If a belt is too tight, wear to bearings for the water pump, alternator, and engine crankshaft can result.
Some late-model Chrysler engines require a torque reading to be taken when tension is applied to the generator drive belt. This is especially important on the longer, multiribbed V-belts.

0900823d8004ed76.jpg


Pry the idler or generator pulley to adjust the belt to specifications.

0900823d8004ed77.jpg


Tighten the idler or generator pulley fastener.

0900823d8004ed78.jpg


Start the engine and check the belt for proper operation.

Any more questions please ask. Good luck.

Jan 24, 2009 | 1996 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...