Question about 1995 Honda Accord

1 Answer

My indicator came on it says maintainance - 1995 Honda Accord

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

.same

Posted on Sep 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to no this code for a ford explorer, gas problem, code p0193


Fault Code Definition P0193
  • Fuel Rail Pressure Sensor Circuit High Input
What does this mean?
The Powertrain Control Module (PCM) needs to know the fuel pressure at all times so it can effectively control the fuel injectors and deliver the optimal amount of fuel into the engine's combustion chambers for maximum power and economy while maintaining the lowest tailpipe emissions.
Code P0193
indicates that the signal from the Fuel Rail Pressure Sensor and/or its circuit is too high, indicating a fuel pressure condition that is abnormally high.

Mar 05, 2017 | Ford Cars & Trucks

1 Answer

Why are A/C and heat lights on at same time on controller?


if you have a climate control system the that would indicate both units operating to maintain the climate control setting
if the day gets too hot then the heat should go out or of the night is too cold the ac will go out

Sep 12, 2015 | 1996 Lincoln Mark VIII

1 Answer

I have a 91 jeep wrangler the 4 wheel drive stop working iv check the vacume hoses and they r good iv trace them bact to transfurcase to the front intake iv got vacume to the hoses by the batter but none...


first off what does that mean? 91 command trac system.
1: light dead in dash. ( means squat)
2: shift lever will not move. (i guess its ok)
3: tires actually do not turn on 4 ends of axles. (guess fails)

we cant guess, what tests fail, you must say.
do you have drive on the front prop shaft,
from transfer case to the front axle.?
91 books are hard to find, but alldata.com does cover it.
ever read the FSM or alldata.com its there.
my guess is you are saying the shift motor is dead/. that it?
this?



25543740-y0lpcx5ujcsqxilomiw3wt0j-2-0.jpg if yes, did you do the steps in the FSM book yet>? read it?

  1. Raise and support the vehicle safely.
  2. Disconnect the vacuum harness and connect a hand vacuum pump to the front port. Apply 15 in. Hg (381mm Hg) of vacuum to the front port and rotate the right front wheel to fully disengage axle shafts.
  3. The shift motor should maintain the vacuum applied to the front port for a minimum of 30 seconds. If the motor does not maintain the vacuum, replace it. If the motor does maintain vacuum go to Step 4.
  4. Connect the vacuum pump to the rear port. Cap the port for the indicator lamp switch and apply 15 in. Hg (381mm Hg).
  5. The shift motor should maintain the vacuum applied to the rear port for a minimum of 30 seconds. If the motor does not maintain the vacuum, replace it. If the motor does maintain vacuum go to Step 6.
  6. Remove the cap from the port for the indicator lamp switch and determine if vacuum is present. If present, the shift motor is functioning properly. If not, proceed to Step 7.
  7. Apply 15 in. Hg (381mm Hg) of vacuum to the shift motor rear port. Rotate the right front wheel to engage the axle shafts. The axles must be completely engaged!
  8. Determine if vacuum is present at the port for the indicator lamp switch. If present, the shift motor is functioning properly. If not, replace the shift motor.
85357331.gif tests: this is just a vacuum servo , called a motor by jeep, its not a motor of any kind its a vacuum servo actuator.
it can be removed and bench tested, easy. just like all servos




25543740-y0lpcx5ujcsqxilomiw3wt0j-2-1.jpg

Mar 09, 2015 | Jeep Cars & Trucks

1 Answer

My oil indicator light is on and i dont know what the probelm is?


It's usually an indication of low oil pressure. You can try changing the oil and adding a stability agent. The main bearings create and maintain the oil pressure so it's a good indication that they are getting worn.

Oct 08, 2010 | 1991 Dodge D150

1 Answer

How do you reset maintainance message in display


Set the key to position 1, get the service indicator on the dash by using the steering wheel buttons, press and hold the R on the cluster until the confirmation message comes up, and use the steering wheel buttons to confirm the service.

Oct 03, 2010 | 2006 Mercedes-Benz CLK 500

1 Answer

A red light indicator is on the section of my dashboard on my speedometer area that indicate need maintainance. it use to be yellow noe it is red


I used to have an older Honda where the oil change indicator would go from green to yellow to red as the odometer rolled over. There is probably a way to reset this. Ask the dealer about it.


Jul 06, 2010 | 1995 Honda Accord

1 Answer

This problem is on a 1998 740iL. When I press the steering wheel cruise control activator - the green indicator light comes on but when I press the "set" (+) button it does not engage and the car does not...


my BMW 740i has a problem with the cruise control.
The cruise control will work for about 20 miles and then quit working and will not work again.

May 17, 2010 | Cars & Trucks

1 Answer

1994 22re 4x4 problem


your transfer case is not working properly, try this trick, shift into 4wd and gently back up the car and go forward and back up again wait for the indicator light to come back again, goodluck, otherwise you need to have those transfer case checked and maintained, have those front hubs checked and maintained too. Its would be better to use your 4WD more often. Try this trick not on a paved road pls.

Nov 25, 2008 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...