Question about 2001 Hyundai Tiburon

Open Question

Torque on rear wheel bearing nut - 2001 Hyundai Tiburon

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 15 Answers

SOURCE: VW Jetta torque setting and hub nut size????

129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Posted on Jun 01, 2009

  • 65 Answers

SOURCE: 2000 hyundai accent

Their shop website says below but you can call the service department. usually you want to tighten it just until it starts to not rotate freely then back off just a little bit. It should spin freely.

Hub bearing starting torque [Limit] : 1.8 Nm (18 kgf·cm, 1.33 lbf·ft) or less

Posted on Sep 05, 2008

BCally1
  • 133 Answers

SOURCE: Rear hub nut torque setting Hyundai coupe 2000 se

65-80 ft.lbs

Posted on Jan 06, 2009

  • 2 Answers

SOURCE: what torque for rear wheel bearing Ford Focus 2000

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Posted on Jan 27, 2009

  • 1 Answer

SOURCE: changing front wheel bearing

first take the wheel off
Then take the caliper off the rotor
Then take the rotor off the CV joint spindle
You will need to remove the three bolts that hold the bearing in place.
You will either need to remove the two bolts that hold the strut or
you will need a Puller.

Posted on Apr 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know the torque setting for the rear weel bearing on my 2001 ford focus. it takes a 30mm socket.


The torque setting 49 ft. lbs.


Torque Specifications
Description Nm lb-ft lb-in Wheel nuts - steel/alloy wheels 128 94 - Wheel spindle retaining nuts 66 49 - Wheel cylinder retaining bolts 12 9 - Rear brake pipe to wheel cylinder union 8 - 71 Rear wheel speed sensor retaining bolt 9 - 80 e0001241.jpg
Item Part Number Description 1 - Tie bar and knuckle 2 - Backing plate 3 - Wheel spindle 4 - Sensor ring - anti-lock control 5 - Grease cap 6 - Wheel bearing retainer 7 - Drum

Apr 26, 2011 | Ford Focus Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

Front bearing nut torque specification rear wheel drive?


front bearing wheel nut holding axle on? 115 foot pounds and hammer in or crimp the nut after tightening. ^ like shape into slot of axle this locks the axle. for the wheel bearing for rear wheel drive the nut should be tightened by hand till tight 15 foot pounds then backed off 1/4 turn, be sure there is plenty of grees in the bearing cup before tighting nut be sure to line up slot for key with rotor on the rotor should turn free and should not have any slop in it, put the wheel on it and put the nuts on and try wiggleing the wheel back and forth if any movement readuast nut. If it is to tight it will over heat outter wheel bearing, also be sure there is greese in inner wheel bearing.

Jul 14, 2010 | 2000 Mercury Grand Marquis

1 Answer

Does anyone know the torque wrench settings for the rear hub/wheel bearing nuts on a 2002 Peugeot 206 1100cc please? Also the road wheel bolts?


Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event

Jan 23, 2010 | 2005 Peugeot 405

1 Answer

How to replace a rear wheel bearing 1996 nissan maxima gle


  • Remove tire
  • Remove brake caliper assembly
  • Remove brake rotor
  • Remove hub cap
  • Remove cotter pin
  • Remove wheel bearing lock nut & washer
  • Remove wheel hub bearing from spindle
to install wheel bearing nut torque to 137 Ib to 188 Ib

Sep 26, 2009 | 1996 Nissan Maxima

1 Answer

Loose rear wheel, believe it is the bearing. How do I repair it?


drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

May 30, 2009 | 1999 Hyundai Sonata

1 Answer

We are trying to replace my rear wheel bearing. Can anyone give any ideas how to get it apart?


here is how to replace it on a 2 wheel drive please do not forget to rate and comment about your experience today. 2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle

06017-esca-g92.gif
06017-esca-g93.gif
06017-esca-g94.gif
06017-esca-g95.gif 06017-esca-g96.gif

To install:
  1. Install or connect the following:
    • Wheel bearing in to the knuckle
    • Snapring
    • Wheel hub into the wheel bearing
    • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake drum
    • Rear wheel
    • Negative battery cable
06017-esca-g97.gif
06017-esca-g98.gif

Apr 11, 2009 | 2005 Ford Escape

Not finding what you are looking for?
2001 Hyundai Tiburon Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...