Question about 1989 Toyota Cressida

1 Answer

What motor oil does a 1989 cressida use - 1989 Toyota Cressida

Posted by on

  • tammy owen Jun 19, 2013

    i use 10w30 in my cressida

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

20/50 multigrade,the best you can afford....

Posted on Sep 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the freeze plug located at on a 1989 cressida


The freezer plug is located on the left side of the motor under the exhaust manifold towards the back.I think its visible if you take off the metal heat shield that's on the manifold or maybe from the bottom if you lift the car.If its not leaking from there than it could be coming from the back of the motor. There are hoses, a EGR cooling plate and metal water lines on the motor.

Jul 09, 2014 | 1989 Toyota Cressida

1 Answer

Toyota cressida blower motor only has 2 speeds


Could be the switch or wiring. The resistor can be checked with an ohm meter but they are substantial and not prone to turning up faulty when new.

Oct 03, 2017 | 1989 Toyota Cressida

1 Answer

1989 Toyota Cressida ,won't start. Battery is


Check starter, spark and fuel pressure.

Apr 13, 2012 | 1989 Toyota Cressida

1 Answer

My 1989 cressida gli 6 is using too much oil and i dont know what might be the reason.


silly question but have you checked for leaks? you could have a gasket gone,

Jan 06, 2012 | 1989 Toyota Cressida

2 Answers

I have a toyota cressida gli 6 1989 ,has spark and fuel,motor swings but just wont start


Where had you checked spark first? Is the distributor turning? This can be checked by removing the distributor cap and making sure the shaft is turning as the engine cranks. Have you checked that there is spark at the plugs? The ignition coil could be weak and still produce some spark but not enough to start the engine. Be cautious of all rotating belts and pulleys around the engine while working under the hood.

May 19, 2011 | 1989 Toyota Cressida

1 Answer

Oil-leak on spark plugs


Oil leaking on the spark plugs is caused by a defective valve cover gasket, remove and replace the valve cover gaskets.

Mar 22, 2011 | 1989 Toyota Cressida

1 Answer

Oil is getting inside distributor cap, have new distributor on it . Its a 1989 Toyota Cressida


check you PCV system you are getting to much crankcase pressure and this is causing the oil in the distributor, if the PCV system is working then suspect to much blow-by from piston rings.

Jan 29, 2011 | 1989 Toyota Cressida

2 Answers

1989 tOYOTA CRESSIDA sAPRK PLUGS WELLS. OIL IN THE SPARK WELL


The 7MGE has 2 separate valve covers/gaskets with 8 screws holding each cover that will loosen over time.
Find the phillips screws holding on the covers and retighten snugly by hand do not overtighten!
Pull plug boots/wires by the boot not the wire and use paper towels or rags on a long screwdriver etc to absorb the oil from the wells.
Carefully clean plug boots with spray brake cleaner (avoid spraying anything but the boot) and let dry.
Apply 100% silicone grease to inner boot before reinstalling to allow future removal without damage.
If your engine is particularly dirty you may need to remove the covers first and clean all mating surfaces then reinstall.

Feb 24, 2009 | 1989 Toyota Cressida

1 Answer

Water in the resevoir is boiling


Blown head gasket, blocked radiator, faulty rad cap, not pressurising eg hole som where, fan not turning correctly, 4M series have a bad habit of corroding the head. if incrrect coolant mixing...

Jul 15, 2008 | 1989 Toyota Cressida

Not finding what you are looking for?

Open Questions:

See all 1989 Toyota Cressida Questions

Cars & Trucks Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...