Question about 2002 Hyundai XG350
Check battery connection as a lose connection triggers the air bag light. I found lead terminal cap at the auto store. add and tighten snugly
Posted on Apr 30, 2016
It may appear if there is a particular sensor fails.
Try stopping the indication using the following technique.
Sometimes the problem could be solved.
If you can get an OBD 2 scanner off eBay (US$ 6), you could be able to communicate with your car ECU (Electronic Control Unit) using the smart-phone app.
So that, there is a chance to CLEAR all the error indications.
After that, if problem still persists, it means the vehicle need full scan (you can't do this at home, probably seek a vehicle garage).
Posted on Oct 22, 2015
If an air bag warning light is illuminated while driving the air bag safety system has been disabled and will not activate in the event of an accident .. it could be your crash sensor or the air bag inflator
Posted on Sep 09, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury or death.
Posted on May 20, 2009
You need to either have the dealer reset it or you can do it if you have VAG-COM. Vag-Com is a piece of diagnostic software that uses a special cable to hook up to your car. You can read/clear codes among a ton of other things. It's very common for VW guys to have. Much easier than going to the dealer if you can find someone close to you. The guys over at www.tdiclub.com are always more than willing to help out a fellow VWer. There is a list of guys with the software - you can actually do a search to see if there's anyone near you. www.vagcomlocator.com or go to www.tdiclub.com
Posted on Jul 11, 2009
If you mean the passenger airbag light no longer lights up and airbag light on the dash blinks at start-up and then stays on; the read the below and check this site:
I went to radio shack cost me $2.99 for 3 bulb packet. But the post below worked. It really didn't that long, pretty easy job. Took longer to find the tools. The first guys idea/fix, the second guy gave pretty good instructions. Just a little more detail: (3) the clips are one each side of the panel; (5) these two screws are on the inside lower part of module, (6) unclip the plastic tabs from the back (where the plug end is) first and it should lift up easily.
I had this happen on my 98 Ranger.(code 27) My light on the module that turns off the passenger side airbag was burnt out. I went to Radio Shack and bought a 12v light with wires attached and soldered them to the existing light.(didn't even take it out!) It fixed it!! Cost, about $1.50 and 20 minutes of fix time.
Note: If the light by the key switch to turn off the passenger side airbag does not work, it disables the entire airbag system! Hope yours is as easy to fix.
Thanks for your post. I have no way to read codes, but I heard the five tone alarm every time I started the vehicle and the passenger air bag off light did not light up. I was skeptical, but tried your advice and it worked.
1) 12-volt colored lamp (Radio Shack part: 272-1099)
1) socket set
2) philips head screw driver
3) soldering iron
1) remove ash tray from console panel
2) using a socket set, remove 4 hex head screws from console panel
3) pull console panel out of the two clips
4) remove connector from air bag key module in console panel and take console panel to a work bench
5) remove 2 philips head screws to remove the airbag key module
6) carefully unclip the plastic tabs that hold the airbag key module case together
7) remove connector circuit board from air bag key module
8) solder the yellow replacement lamp to the two solder pads for the original lamp on the back side of the circuit board (which wire to which pad does not matter)
9) tie the replacement lamp in place next to the original lamp
10) replace the circuit board in the airbag key module and snap the case back together
11) connect the airbag key module in the truck and start the engine to check that the lamp illuminates and that the alarm does not sound
12) screw the aribag key module back into the console panel
13) snap the console panel back into the truck
14) replace the 4 hex head screws
15) replace the ash tray
Posted on Nov 04, 2009
Tips for a great answer:
Dec 30, 2016 | Cars & Trucks
Mar 03, 2011 | 2002 Ford Explorer
Feb 15, 2010 | 2006 Hyundai Santa Fe
Jan 28, 2010 | 1995 Honda Accord
Jan 15, 2009 | 1998 Land Rover Range Rover
Jun 20, 2008 | 1996 Pontiac Grand Am
554 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: