Question about Ford F-150

1 Answer

There is no J hook arm on my f-150. I purchased rain-x Weatherbeater wiperblades which has a "j-hook' arm connector. The tip of my wiper shaft doesn't seem to fit. Do I need to go to a ford dealer?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,002 Answers

There should be a small plastic piece in the package with the wiper blades. It should convert the "j hook" to fit your wiper arm. Hope this helps.

Posted on Sep 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

Passenger side wiperblade arm not moving, driver's side working fine.


you need to check to make sure the "arm" is moving , some gm vehilce have a sealed wiper unit, but the alero should still have arms. turn wipers on and look down at the cowl vent and see if it appears to move. if it is the mounting post for the arm on the passenger side has PROBABLY stripped out the soft lead mount at the bottom of the wiper arm. make sure the wipers are "parked", then carefully try to wiggle the pass side back and forth (its normal motion...). if it moves you will need to pop the arm off(super careful here..) and the post that looks smooth must be cleaned out with a fine pick or equilalent, the post accually has splines all around to engage the wiper arm. put on the new arm.. presto.... wipers.

Mar 06, 2011 | 2004 Oldsmobile Alero

1 Answer

I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
  1. Turn ignition switch to ACCY position.
  2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
  3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
To Install:
  1. Insert wiper arm hook through opening in wiper blade.
  2. Place wiper blade pivot in the inside radius of wiper arm hook.
  3. Pull on wiper blade pivot into hook until it locks into place.
  4. Check wipers for proper operation.
Wiper Arm To Remove:
NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
  1. Remove washer hose.
  2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
  3. Remove wiper arm from shaft.
To Install:
  1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
  2. Press arm assembly on shaft and push retaining latch IN.
  3. Connect washer hose.
  4. Remove windshield markings and check wipers for proper operation.
prev.gif next.gif

Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

Wipers will not turn off?


are you sure there not turning on or just not inguageing .. on your windshield ont he out side rear the wipre arm base theirs a black panal you can take off.. under that youll see your wiperblade motor and the 2 matle hands that turn the blades.. have somone turn them on and listen near the motor see if the motor is buzzing then youll know if its a fried motor.. also look at the arms make sure there on the wiperblade.. might soudn dumb but youd besuprised. from there there is a wiper relay switch masicly the lil black nob you turn to turn them on.. thats the last resort cause in 5 years of car service ive never replaced one

Aug 12, 2009 | 2003 Hyundai Tiburon

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

1 Answer

How to replace a wiper arm on a 1998 KIA Sportage


If shaft is moving the nut on the arm is loose. open the black rubber cap on the arm ant fasten the nut. If shaft not moving, motor damaged or conecting arms hooked out. Willem SA

Apr 10, 2009 | 1998 Kia Sportage

1 Answer

How do you get the wiper arms off of a 1998 dodge ram?


Wiper arms are generally held on one of two different ways. Either with a nut under a little cap that flips up above the pivot shaft, or a lock tab at the base of the wiper arm that pivots out and away a little from the pivot shaft. With either one, you will have to flip the wiper arms away from the windshield because they will not pull off the pivot shaft until the wiper blade spring tension is no longer acting against the windshield. Here's a pic of the lock tab.d76e2b6.jpg

Mar 14, 2009 | 1991 Dodge Ram 150

1 Answer

Driver's side wiper arm on my '93 Sidekick is not working


This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT
  1. Disconnect linkage assembly from wiper motor shaft.
  2. Disconnect electrical connectors from wiper motor.
  3. Remove wiper motor attaching bolts, then wiper motor.
REAR
  1. Remove wiper blade and arm assembly.
  2. Remove access panel on back door.
  3. Disconnect linkage assembly from wiper motor shaft.
  4. Disconnect electrical connectors from wiper motor.
  5. Remove wiper motor attaching bolts, then wiper motor.
Skill
Level
Mfg.
Warranty
Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

Jan 20, 2009 | 1995 Suzuki Sidekick

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...