Question about GMC Sierra 1500

Open Question

2008 gmc sierra wipers - Sierra 1500 GMC Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rockitman187
  • 2559 Answers

SOURCE: gmc sierra 2008 low tire pressure problem

You can follow this to reset it.
Ignition ON, initiate the TPM Learn Mode
using one of the following procedures:

  1. On vehicles equipped with keyless entry, simultaneously press the keyless entry transmitters lock and unlock buttons until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
  2. On vehicles not equipped with keyless entry, press and release the driver information center (DIC) INFO button until the TIRE LEARN message appears on the DIC display. Press and hold the SET/RESET button until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
  3. Increase/decrease the tire pressure for 8-10 seconds then wait for a horn chirp. The horn chirp may occur before or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached. Once the horn chirp has sounded, the sensor information is learned and the turn signal in the next location to be learned will illuminate.
    After the horn chirp has sounded and the right front turn signal is illuminated, repeat step 2 for the remaining 3 sensors in the following order:
    3.1. Right front

    3.2. Right rear

    3.3. Left rear

    When the left rear sensor has been learned and a double horn chirp has sounded, the learn process is complete and the RCDLR exits the learn mode.
    Ignition OFF, adjust all tires to the recommended pressures

Posted on Jan 22, 2009

  • 3600 Answers

SOURCE: where is the wiper motor on a 2003 gmc sierra

Replace the multifunction switch where the wiper switch and turn signal are located on the steering wheel. There are two screws that hold it on and you can remove the cover on the steering wheel with a tork wrench #6 I think, could be next size down #4 then remove the two screws holding the switch in place. And disconnect the wiring Replace the multifunction switch where the wiper switch and turn signal are located on the steering wheel. There are two screws that hold it on and you can remove the cover on the steering wheel with a tork wrench #6 I think, could be next size down #4 then remove the two screws holding the switch in place. And disconnect the wiring connector and replace. connector and replace. If you need more help post here and Thanks for using Fix-ya.

Posted on Aug 23, 2009

  • 432 Answers

SOURCE: 1990 GMC Sierra 1500 pickup. Windshield wipers, Cruise Control

May want to look at replacing the wiper circuit board.It is located on the firewall adjacent to the wiper motor and has a some what square black cover with 3 torx screws and wireing harness pluged into the side.We had a truck that every time you washed it the wipers would stay on until it dryed out.You can try removing it and spaying it down with contact cleaner just watch the brease on the two contact tips.Well hope this helps.

Posted on Feb 05, 2010

ftw1952
  • 10319 Answers

SOURCE: c hange rear blade 2008 gmc

At the mounting area of the blade to the rotating wiper arm is a tab that has to be pushed in and held to remove the wiper blade. The tab will be on the wiper blade's center housing ansd is very small to see

Posted on Apr 25, 2010

rabbit7954
  • 417 Answers

SOURCE: I have a GMC Sierra 2008 and I can't find the oil ...

The oil plug will be located on your oil pan. If you checked ther are you sure you checked all areas? I have never seen one anywhere else. Especially on an american made vehicle. I don't know your experience level but the oil pan is located just in front of the transmission under the engine. I hope that helps you find it.

Posted on Jul 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2008 GMC Sierra 1500 4 wheel drive with a 4.8 motor I have no power to my fuel pump fuse.


Chevy Silverado and GMC Sierra Fuel Pump/Fuel System - Edmunds.com

forums.edmunds.com > Chevrolet > Chevrolet Silverado 1500

Mar 20, 2011 - 30 posts - ‎19 authors
Learn more about Chevrolet Silverado 1500 at the Edmunds.com Car Forums! ... problem with my 2000 GMC Sierra 1500 4.8LTR V-8 you described in your post. .... Ihave a 2008 gmc sierra last 8 vin 8Z160870 4WD pickup was ... removed power and truck died. have no power at 20amp pump fuse, key on ... Chevy Silverado and GMC Sierra Starting Problems ...
30 posts
Apr 18, 2013
8 - Car Forums at Edmunds.com
30 posts
Nov 7, 2011
9 - Edmunds.com
30 posts
Oct 28, 2008
More results from forums.edmunds.com

SilveradoSierra.com • Cranks but wont start. Fuel problem ...


Jan 25, 2016 | GMC Cars & Trucks

1 Answer

2008 GMC SIERRA wipers Quit after ice storm, mechanic says not fuse not wioer motor or switch or wiring


Get a new mechanic. Or a technician would be better. If it.s not the wiring then its probably the motor.

Dec 24, 2013 | 2008 GMC Sierra 1500 2WD

1 Answer

C hange rear blade 2008 gmc


At the mounting area of the blade to the rotating wiper arm is a tab that has to be pushed in and held to remove the wiper blade. The tab will be on the wiper blade's center housing ansd is very small to see

Apr 25, 2010 | 2008 GMC Acadia

1 Answer

ONe wiper works the other one doesn"t


It may be that the connecting rod popped out of its socket. Remove the cowling and take a look at the assembly..

Mar 29, 2010 | 2003 GMC Sierra

2 Answers

1990 GMC Sierra 1500 pickup. Windshield wipers, Cruise Control


May want to look at replacing the wiper circuit board.It is located on the firewall adjacent to the wiper motor and has a some what square black cover with 3 torx screws and wireing harness pluged into the side.We had a truck that every time you washed it the wipers would stay on until it dryed out.You can try removing it and spaying it down with contact cleaner just watch the brease on the two contact tips.Well hope this helps.

Feb 05, 2010 | 1990 GMC Sierra

1 Answer

1999 gmc sierra wipers will only run on high. Any idea why?


The wiper motor control module needs replacing. On some models you can replace the "pulse board". On some you must replace the wiper control module which mounts directly to the windshield wiper motor. This is a very common GM problem.

Jan 19, 2010 | 1997 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...