Question about 1991 Saab 900

1 Answer

How do you remove a flexplate from a 1991 sabb automatic trans

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 326 Answers

You either have to remove the engine or the transmission which ever is the more acessible

Posted on Sep 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a99 chevy sunurban with a 4L60-E transmission i lost all gears, had the trans febuilt, i installed the rebuilt trans with a new torq converter and i still have no gears, what could possibly be wrong


Make sure you engage the convertor all the way into the trans-three stages while pushing in and turning, or else the ears on the conv won't engage the oil pump. Also check your flexplate for cracks around the bolt holes while you have the trans out,it won't disable your trans unless the flexplate cracks completely. Of course, check fluid level and make sure you don't have a trans cooler leak in the radiator. Good luck.

Sep 25, 2013 | Cars & Trucks

1 Answer

How to change a 1991 cadillac seville starter


I will paste instructions from autozone.com below, but recommend you also read thru my post at http://www.fixya.com/cars/r5973094-starter_replace and let me know if you have questions.

4.5L and 4.9L Engines

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle securely on jackstands.
  3. Remove the starter motor shield.
  4. Remove the exhaust front and rear pipe assembly.
  5. Remove the flexplate inspection cover.
  6. Disconnect the solenoid 'S' terminal nut and battery cable nut.
  7. Unbolt the starter motor mounting bolts, and remove the starter motor.
0fa6f1f.gif

Fig. Later model starter location and mounting on the 4.9L engine


To install:

  1. Install the starter motor, and tighten to 32 ft. lbs. (43 Nm).
  2. Install the solenoid 'S' terminal nut. Tighten the nut to 35 inch lbs. (4 Nm).
  3. Install the battery cable nut and tighten to 12 ft. lbs. (15 Nm).
  4. Install the flexplate inspection cover, the front and rear exhaust pipe assembly and the starter motor shield.
  5. Lower the vehicle.
  6. Connect the negative battery cable.

Nov 01, 2010 | 1991 Cadillac Seville

1 Answer

1991 f350 , 460 ci , automatic wont go into overdrive when the tranny gets warm


ok chech the water hosed in the radiator (both) because if the trans oil is over heat the trans got problems. The trans oil runs trough the radiator.

Oct 21, 2010 | 1991 Ford F350

1 Answer

My car has a worn out engine rear seal how can I replace it?


This is a fun one. You can do this 2 different ways. One of which, remove the transmission and flexplate (automatic trans.) or flywheel (manual trans.) and you can loosen the rear main cap and pull the old rear main seal out and install the new one. The other way of replacing it is removing the engine and replacing the seal on an engine stand. Either way, it'll take some time to do.

Apr 04, 2010 | 1994 Ford Ranger Supercab

1 Answer

How to to install a manual trans in an automatic 92 corolla


Sometimes the pinion gear is a different size for the automatic and smaller for the manual, make sure you get this right or it will chatter your teeth out. You also need to find a car like yours with a manual trans so you can pull all these parts out, shifter, clutch pedal, a hydraulic master and slave, your speedo probably won't work, or fit, maybe. Your propeller shaft might not be the same length, but you can get that from the donor car. I would find another auto to put in there, it would be easier. Hope this helps.

Mar 31, 2010 | 1992 Toyota Corolla

1 Answer

Is a flexplate an flywheel the same thing


if it is a standard transmission you buy a flywheel. if its an auto, you buy a flexplate.

Mar 08, 2010 | 1991 Ford Mustang

2 Answers

1991 isuzu trooper


The way the shifter is connected to the transmission.

Sep 15, 2009 | 1991 Isuzu Trooper

1 Answer

How do i remove the transmission off a 1991 isuzu pickup?


put truck on jack stands disconect batt . remove driveshaft/ starter .torqconverter bolts if automatic. if standerd slave cyl .shifter linkage .when all ***** are out of your way remove crossmember under trans . if 6 cyl dont let distributor hit firewall remove bellhousing bolts trans should fall out ..... support trans with jack .....dont get under trans it is heavey!!!!!!!!!!!!!!

Mar 05, 2009 | 1991 Isuzu Pickup

1 Answer

1995 Mitsubishi Mirage breaking flexplates


the dish in the center of the flexplate should protrude tword the engine, also check for excessive torque convertor run out, as that can crack the flexplate

Nov 10, 2008 | 1995 Mitsubishi Mirage

2 Answers

Where is the crankshaft position sensor is located


Year,engine size,and transmission type wasn't stated,so my reply may not cover ALL.as a generic answer.On all of the Sebrings i have personally repaired,the models that had automatic transmissions ALL had the crankshaft position sensor mounted into the transmission bellhousing with a 10 mm bolt.It is located on the driver side of the vehicle,exactly where the trans bolts to the engine block.If you are standing at the rear of the engine,on the driver side fender facing the engine bay,the sensor is located at about 2 o'clock if the rear of the engine were a clock.There is also a VERY important adjustment procedure in relation to the depth of the sensor in the hole it is mounted in.It is adjustable up and down in relation to the flexplate,and should have an air gap of approximately .030".Too close to the flexplate,the sensor will hit the flexplate and destroy the sensor,too far away and the sensor will not read and the engine won't run.

Jul 18, 2008 | Chrysler Sebring Cars & Trucks

Not finding what you are looking for?
1991 Saab 900 Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

rgbypoet

Level 2 Expert

166 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...