Question about 1987 Ford Bronco II

1 Answer

Where is the igition control module located on the 2.9 v-6.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 41 Answers

It is attached the the side of the distributor, it has a big plug with alot of wires going into it..if looking from the passenger side you can see the plug that connects to the ignition control module, just over the valve cover.. there are 3 really small bolts that hold it on, i had to make a socket, had to grind the outside of the socket so it will fit into the recessed holes..the best way to see the bolts is to use alot of light and a mirror..

Posted on Feb 16, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2001 Chevy caviler replaced coils and igition control module

Crank sensor. About the only thing left, except checking power and grounds. wiring. fuses.

May 30, 2016 | Cars & Trucks

1 Answer

No power to igition switch

check the fuse for the ignition if not maybe a faulty wire or entire ignition control module

Sep 14, 2015 | 1988 Ford F 150

1 Answer

I cannot find my igition module olsmobile cutlass1993

you don`t say if this is 4 or 6 cylinder motor. if its a 4 the module is bolted on the back of the motor firewall side with the ignition coils attached to it. note the crank sensor is fastened to the module and sticks into the motor so when you pull the ignition module the crank sensor will come out with it. on a 6 its located at the front of the motor(rad side) near the bottom of the motor and the coil packs are fastened on top of the module, and has electrical plugs connected to it. the module is bolted to engine with 3 bolts and the coils come off with the module. its easier to remove the assembly from under the car.

Sep 16, 2014 | Cars & Trucks

1 Answer

Location of igition module of 2003 ford e350

it varies amoung cars-usually if u follow the coil it will lead to it-but engines are so full of wiring etc that a manual like haynes or chilton in the library xplains--if issues with ignition-inspect plugs and cables 1st-rubber or inside maybe worn--distributer or coilpacts may have wear too--

Aug 01, 2014 | Cars & Trucks

1 Answer

I need to replace my 1984 245 DL ECU and do not know where to locate it ?

the ECU is located behind the right kick panel. the Electronic Igition control unit is located under the hood on the right front corner of the engine compartment.

Jan 27, 2012 | Volvo 240 Cars & Trucks

1 Answer

I'm not getting electric to my coil. Could it be the igition module? And where is the module located?

Yes, it COULD be the ignition control module ( ICM ). this component is usually mounted inside the distributor - follow where the wires go into the distributor, and that should be the ICM. The ICM requires dielectric grease on the backside to work properly, and sometimes the grease dries up, breaking the circuit needed to work. There is also another small coil mounted inside the distributor that goes around the dist. shaft called a pickup coil - these go bad too, but are much harder to change as the distributor must be removed to change out this coil. Many auto parts stores like Autozone have the necessary equipment to test the ICM if you pull it out and take it in - I would suggest this BEFORE you buy a replacement.
Hope this helps!

Nov 05, 2010 | 1987 Plymouth Voyager

1 Answer

Is what they refer to as an ignitor a coil module on a 1993 ford laser

The igition module is also refered to as the igniter. The module is the control unite that takes the information as to the location of the crankshaft to timing assembly. It synchronizes the two and tells the distributor when to fire the pulse to the spark plugs. These units are prone to failure and need to be isnstalled with lots of dielectric grease (between the module and the mounting location) which acts as a heat sink. Hope this helps.

Jun 11, 2010 | 2006 Ford Laser

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

1 Answer

Brake Light Control Module

91 Honda Accord has 2 separate tail lights on each side(total of 4 pieces). My problem stemmed from a faulty control module on the right hand side(passenger side). The module in question is located inside the smaller of the 2 tail light sections. In order to change the module you have to remove the tail light. There are 4 nuts holding in the taillight section and 2 phillips head screws holding the module in. The module on this side is 6 pin plug in. The one on the drivers side is a 5 pin plug in. Whole effort takes about 45 minutes. It is strictly plug and play.

Feb 05, 2009 | 1991 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers


Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides