Question about 2000 Mercury Mystique

Open Question

Timing belt diagram for a 2000 mercury mystique 2.0 gs

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

KCGTODAD
  • 169 Answers

SOURCE: trying to get diagram to change a timing belt for

Ford TSB 99-25-4 provides the following corrected information:
To achieve proper timing belt tension on this engine, Ford says the camshaft sprocket bolts should be loosened enough to permit the sprockets to turn freely on the camshafts. Once this has been done, rotate the crankshaft clockwise so cylinder No. 1 is at top dead center. Then, install the camshaft alignment tool in the camshaft slots to hold the cams in place.

  1. Back out the tensioner bolt four full turns and position the tensioner so the locating tab is at approximately the 4 o'clock position. Line up the hex key slot in the tensioner-adjusting washer with the pointer that is located behind the pulley.
  2. Working counterclockwise from the crank sprocket, install the timing belt.
  3. Rotate the tensioner locating tab counterclockwise and insert the locating tab into the slot in the rear timing cover.
  4. Position the hex key slot in the tensioner-adjusting washer to the 4 o'clock position.p>
  5. Tighten the attaching bolt enough to seat the tensioner firmly against the rear timing cover, but still allow the tensioner adjusting washer to be rotated using a 6 mm hex key.
  6. Using the hex key, rotate the adjusting washer counterclockwise until the notch in the pointer is centered over the index line on the locating tab. (The pointer will move in a clockwise direction during adjustment).
  7. While holding the adjusting washer in position, torque the attaching bolt to 18 lb-ft (25 N.m).
    Note: If the pointer does not remain centered over the index line during final tightening, loosen the bolt and repeat the procedure beginning with step 4.

Posted on Sep 18, 2009

  • 1 Answer

SOURCE: mercury mystique starter location

its a 6 I beleive its a 2.5

Posted on Mar 24, 2009

c17hydro
  • 2984 Answers

SOURCE: 2000 mercury sable drive belt

For VIN 2 FLEX Fuel:

4488d47.jpg For VIN U and S....with A/C:

c2b84a7.jpg PLEASE DON'T FORGET TO RATE!!!!

Posted on Apr 01, 2009

  • 491 Answers

SOURCE: I need a diagram as to how the serpentine belt

autozone.com

Posted on Jun 09, 2009

  • 316 Answers

SOURCE: Is the serpentine belt and the timing belt the same thing?

Your serpentine belt and timing belt are not the same thing. If your serpentine belt breaks, you will lose your alternator, your cooling system, air conditioning, and your power steering. In turn, it will leave you stranded in a very short period of time.

Posted on Jun 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 mercury mystique 2.0 1989cc enigine i want to fix atiming belt tensioner problem need some help


you need a chilton repair manual.it will show and tell you how to replace timing belt tensioner.you need engine lift or crane chain hoist to support engine while you remove front engine mount to remove timing cover.you need basic mechanic tool set.dont try this task without repair manual hard to do.

Dec 29, 2012 | 2000 Mercury Mystique

1 Answer

Does a 2000 mercury mystique have a timing belt or timing chain


The 2.0l uses a timing belt. The 2.5l utilizes a timing chain.

Nov 15, 2010 | 2000 Mercury Mystique

1 Answer

Need diagram on timing belt for a 1997 mercury mystique its loose do i need to replace it?


timing belt ??? i doubt it is loose or your car dont run
but the accessory drive bely might be loose

Jan 10, 2010 | 1997 Mercury Mystique

1 Answer

Smelled mild burning, lost antifreeze - engine temp Hot. I looked under car and noticed a serverly frayed Belt - NOT the big surpentine belt - another small belt on the driver's side. 1999 Mercury Mystique...


For the 1999 Mercury Mystique Water Pump Belt on 2.5L V6 Engine:

Probable Causes: Belt: worn out, started slipping. Overheating caused by failure of Belt. Lost antifreeze: caused by failure of belt, not turning Water Pump Pulley, not circulating anitfreeze, which resulted in overheating.

Click on the following free direct Link. It has the Serpentine & Drive Belt Diagrams and Tensioners for your 2.5L Engine.
Scroll down the Page (about 1/3rd down) to Diagram #G99H08189, it shows the specific Water Pump Belt.
Note the Tensioner.
http://www.2carpros.com/car_repair_information/year/1999/make/mercury/model/mystique/1999_mercury_mystique_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

Jun 03, 2009 | 1999 Mercury Mystique

1 Answer

Timing Belt Diagram for a 1998 Mercury Mystique


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Timing Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
http://www.2carpros.com/car_repair_information/year/1998/make/mercury/model/mystique/1998_mercury_mystique_timing_belt_diagram_marks.htm

Apr 11, 2009 | 1998 Mercury Mystique

1 Answer

Timing marks


Probably arent any as the timing is controlled by a crankshaft position sensor and is not adjustable.

Jan 13, 2009 | 1999 Mercury Mystique

1 Answer

How to Set timing..


if it like a 98 there are 2 slots on the far end of the cams.remove spark plug #1 closest to the timing belt and set to tdc....then align the two slots so you can get a straight edge into both at the same time....i use a piece of keystock.....place the belt on and thats it....really qiute simple

Jul 01, 2008 | 1995 Mercury Mystique

Not finding what you are looking for?
2000 Mercury Mystique Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

fordexpert

Level 3 Expert

5474 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...