Question about 1995 Ford F250

1 Answer

How do i remove fuel lines from filter and top of gas tank to replace fuel pump in mid tank

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 385 Answers

The colored circular disconnects can be purchased at your local auto parts store for around $10

Posted on Sep 08, 2010

  • John Does Oct 15, 2010

    ******** too. go pay someone with an IQ higher than yours (say 50 or so) to fix it for you...

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I wish to replace both the fuel filter and fuel pump in my 2001 model Hyundai Sonata 2,7 litre V 6 car. Can you please advise a price and exactly where is is located.


Your fuel pump is on top of the gas tank and your fuel filter will be in the fuel line probably about the mid range of the car on the drivers side on the bottom side. The fuel filter should be no more than 25 dollars and the pump is probably going to be in the 90 to 150 range.

Jun 05, 2016 | Hyundai Cars & Trucks

1 Answer

Installed new fuel pump because car had old gas in tank. removed tank and completly drained it. replaced tank and installed new fuel pump and fuel filter. put about 6 gallons of gas in car. have tried to...


Okay, you need to make sure the fuel pump is getting power and that you have the lines hooked up correctly. Also, when you replace fuel pumps you need to remove the air cleaner and use starter fluid to get the engine started.

Jul 09, 2011 | Nissan Z Cars & Trucks

2 Answers

Can you replace an inline fuel filter without replacing the whole gas tank?


the in-line filter is in the fuel line between the tank and the engine, seldom do you have to even touch the tank much less remove it in order to replace that filter. there is a screen on the pump inlet of the
in-tank fuel pump and most likely you are going to have to drop the tank in order to replace the pump or the fuel level sender. make sure there is not a service access hole in the rear of the car such as under the spare tire which could give you access to the top of the tank. on the other hand it is not unusual to find yourself in a situation where a lot of the fuel line must be replaced when you replace the in-line filter. as such you may find yourself with no room to connect the new fuel line to the nipple on top of the tank, without lowering the tank a bit.

Jul 05, 2011 | 1997 Isuzu Rodeo

2 Answers

Were is the fuel filter and is the fuel pump in the gas tank


the fuel pump is in the gas tank and the fule filter runs along the bottom of the Driver side..if your looking at the gas tank follow the gas lines that go toward Eng. you will see the Fuel filter

Dec 30, 2010 | 1996 Dodge Caravan

1 Answer

How to install a few pump that's in the gas tank


remove exhaust system from cat converter back, disconnect fuel lines, disconnect electrical connector remove straps that hold tank up to car remove fuel filler and vent hoses from tank drop tank top of tank remove ring that holds fuel pump assembly in tank. you have to manupliate the assembly out of the tank, its a tight fit, be careful not to break/bend the fuel level sensor. remove fuel lines on top of pump assembly before removing assembly. replace fuel filter also make sure you are careful on reassembly if there is a leak ses light will come on w/evap code (I just done mine (176000 miles)

Aug 20, 2010 | 2001 Saturn L-Series

1 Answer

REPLACEMENT of a fuel filter on a 1997


cd7cd12.gif
The fuel filter (1) is mounted next to the fuel pump module (2), on top of the fuel tank (3)


The fuel delivery system uses quick-connect fittings. The fuel filter mounts to the top of the fuel tank.
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Place a drain pan underneath the fuel filter to catch any spilling fuel that will result from disconnecting the fuel lines.
It may be necessary to support the weight of the fuel tank with a block of wood and a floor jack. Once this is accomplished, loosen, but do not remove, the fuel tank strap bolts. Allow the fuel tank to lower just enough to access the fuel line fittings at the fuel pump module.

6036176.gif

Disengage the fuel line quick-connect fittings from the fuel pump module

02627d0.gif
Be sure to place a drain pan underneath the filter line fittings to catch all fuel spillage

Locate the fuel filter in its mounting on top of the fuel tank. Detach the quick-connect fittings from the chassis fuel supply tube and fuel pump module by squeezing the quick-connect fitting retainer tabs together and pulling the fitting assembly away from the fuel line nipple. The retainer will remain on the fuel tube.

df40422.gif
Using a 10mm socket, remove the fuel filter mounting bolt ...

e9542f8.gif
... then remove the fuel filter from the top of the fuel tank

  1. Remove the fuel filter mounting bolt and remove the fuel filter from the fuel tank.
To install:
  1. Install the fuel filter on the top of the fuel tank and tighten the mounting bolt.
  2. The fuel supply tube (to chassis fuel line), return tube (to pump module) and fuel supply (to fuel filter) tube are permanently attached to the fuel filter. The quick-connect fitting ends of the fuel supply and return tubes are of different sizes.
  3. Apply a light coating of 30W engine oil to the nipples of the fuel filter.
  4. Push the quick-connect fitting over the fuel line until the retainer seats and clicks into place. Be sure the retainer tabs have locked into the case of the fitting.
  5. If necessary, raise the fuel tank and tighten the fuel tank strap bolts.
  6. Lower the vehicle. Start the engine and check for leaks.

Nov 30, 2009 | 1997 Chrysler Town & Country

2 Answers

How do I get to the fuel filter in the gas tank.


I have never seen a fuel filter in the gas tank, fuel pump yes. To get to anything in the tank the tank has to be removed from the vehicle.

May 19, 2009 | 2003 Land Rover Range Rover

2 Answers

1999 jeep cherokee do you have to remove the fuel pump to replace


The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

REMOVAL
  1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
  2. Clean area around filter/regulator.
  3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
  4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
  5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
  6. Discard gasket below filter/regulator.
    1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
    INSTALLATION
    1. Clean recessed area in pump module where filter/regulator is to be installed.
    2. Obtain new filter/regulator (two new O-rings should already be installed)
    3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
    4. Install new gasket to top of fuel pump module.
    5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
    6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
    7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
    8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
    9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

FUEL TANK REMOVAL
  1. Disconnect negative battery cable at battery.
  2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
  3. Raise and support vehicle.
  4. If Equipped: Remove fuel tank skid plate.
  5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
    1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
    2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
    3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
      1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
      2. Disconnect EVAP canister vent line near front of tank.
      3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
        1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
        2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
        3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
          1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
          2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
          INSTALLATION
          1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
          2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
          3. Install hose clamps to hoses. Position clamps between index marks on each hose.
          4. Position fuel tank to hydraulic jack.
          5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
          6. Continue raising tank until positioned to body.
          7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
          8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
          9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
          10. Connect fuel pump module pigtail harness electrical connector near front of tank.
          11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
          12. Connect EVAP hose near front of tank.
          13. Install exhaust tailpipe heat shield.
          1. Install fuel tank skid plate (if equipped).
          1. Lower vehicle and connect battery cable to battery.

Feb 08, 2009 | 1999 Jeep Cherokee

3 Answers

I've got bad gas and need to know the easiest way to drain the tank or otherwise fix the problem.


The tank will have to be removed from the vehicle and completely dried out.Gas tanks no longer have drain plugs as they did 50 years ago.Remove the fuel pump from the top of the tank,and thoroughly clean the tank with brake cleaner and compressed air and let air dry for awhile.The fuel pump and filter will need to be replaced with new,and after all the reinstallation,the fuel line must be disconnected at the engine,and the line flushed with new,clean gasoline as well as the return fuel line.Spark plugs will have to be replaced also.

Aug 12, 2008 | 2003 Toyota Matrix

2 Answers

No fuel from tank to filter


I believe the fuel pump is on the tank, as well as a filter in the tank itself.
  1. I would check for fuses for the fuel pump.
  2. I would check for power to the fuel pump. If there is power to the fuel pump, then the problem is the filter, or a stopped line. If not then replace the fuel pump. Replacing the fuel pump can be tricky, especially if you have a full tank.
  • Lower the tank to the ground.
  • The fuel pump should be on the top of the tank.
  • Remove the wires, and screws holding the fuel pump in the tank.
  • Remove pump from tank.
  • Clean filter in tank, and replace
  • Replace screws and wires.
  • Lift tank back into place, and bolt back in.

Jul 31, 2008 | Ford Ranger Cars & Trucks

Not finding what you are looking for?
1995 Ford F250 Logo

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...