Question about 2000 Mercedes-Benz C-Class

1 Answer

Driver's side brake light out, bulb already changed

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

Check the housing where the light is inserted. The plastic on mine had came loose causing the light to not make contact with the center terminal. If this is the case and you have access to a solding iron melt down the plastic lugs that hold it down in place. Good Luck

Posted on Nov 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why did driver side brake light and back up lights quit?


Trevor if the driver side brake light is out, the bulb should be changed, this may be why blinking fast, as well as reverse lights check fuse,bulb and bulb sockets.

Mar 24, 2016 | Cars & Trucks

2 Answers

ELECTRICAL PROBLEM


take it to a body shop

Nov 27, 2013 | 2000 Dodge Stratus

2 Answers

Only rear driver side brake light will not work when braking need help


Pastor Norman, Pastor Dave here.
Since you already replaced the left rear brake light bulb and that didn't help, please take that bulb socket out again as you did before, and find a way to test the bulb contact for electricity when the brake lights are on. You should get 12 volts out of the "hot" metal contact.
If the other two lights are on, and you have no current in the socket, you either have a bad socket, or a broken wire somewhere.
One way is to go back a few inches and skin off the insulation of the brake light wire and see if there is current back a few inches from the socket. Cover with tape when you finish.
If you decide to cobble a solution, you could run a good wire from the other brake light that works and splice it in to the dead wire.
Be Blessed.

Jan 23, 2013 | 2007 Toyota Corolla

1 Answer

Regular lights work but when u press brake only passenger brake light goes on, i changed the brake bulb which was bad but still no brake light when pushing brake on driver side


sounds like you have a short in the drivers side brake light. it may be due to corrosion in the bulb inlet.try cleaning the bulb socket itself with wd40 or add bulb grease to the bulb. you may have a broken wire to it also.check with a test light to confirm you have power to the bulb when brakes applied,this will take 2 people 1 to press brakes and1 to check for current with a test light at the tail light itself. you may only have corrosion in the brake light bulb socket,so,,do this 1st. with lights off,, remove the bulb on driversside, add a little bulb grease to your bulb,insert it into the bulb socket,and then remove the bulb again,do this 3 times,make sure the bulbs getting connection. then apply the brakes and see if the light comes on. thank you for choosing fixya.com

Feb 27, 2011 | Dodge Sprinter Cars & Trucks

4 Answers

2004 trailblazer left brake light


u have to replace the bulb. There are two wires in the bulb to make it light one is for running lights and other is for brake so just pull it out and see if one of the wires is broken inside. lights are only a couple dollars. good luck

May 08, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Brake lights out.


CHANGE BULB ON LEFT SIDE WITH PROPER BULB

Aug 29, 2009 | 2002 Kia Rio

2 Answers

Turn signals work but the brake lights do not how do i get them to work? i already changed the flasher.


I have a 2001 Ford F150, my brake lights dont work. Ive replaced the bulbs, checked the fuses,and the brake switch on side of the brake pedal was replaced. I still dont have any brake lights. My third brake light works fine, along with my running lights,flashers, blinkers.

Jun 18, 2009 | 1985 Ford F150

1 Answer

2003 dodge durango driver side brake light not working


Use a 12 Volt test light at the tail light connector and see if power is present at the harness, this would indicate a possible defective bulb socket.

Oct 03, 2017 | 1994 Dodge Dakota Club Cab

1 Answer

03 pt ONLY driver brake light out


Ok you can't tell anyone, but I changed the wrong bulb. Only two choices and I changed the good bulb. ugh. all fixed now..

Jan 22, 2009 | 2006 Chrysler PT Cruiser

2 Answers

My brake lights are not working I changed the bulbs and still there is no lights when I press on the brake . what else should I try?


iF YOU ALREADY CHANGED THE BULBS THE PROBLEM IS PROBABLE A BRAKE SENSOR SWITCH UNDER THE DASH LOCATED ON THE BACKSIDE OF THE BRAKE PEDAL LEVER IF THIS DOES NOT THEN CHECK YOUR FUSE BOXES

Oct 16, 2008 | 2003 Hyundai Accent

Not finding what you are looking for?
2000 Mercedes-Benz C-Class Logo

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...