Question about Nissan Pickup
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Lower Ball Joint
You will have to remove it and replace it with a new one. The general steps for doing that is: 1)remove the tire 2)remove the caliper and rotor 3)remove the outer tie rod from the spindle 4)remove the axle nut 5) remove the cv axle 5)remove the nut on the ball joint 6) bang ball joint out and press in a new one. Then reassembly is exactly the reverse as disassembly.
Posted on Jun 10, 2009
SOURCE: upper and lower ball joints
Your better off have it done bt a tech because you need a press to press them out and in. Also you will have a warranty witk the work. You want to be safe messing with your steering and suspension. I hope this helps.
Posted on Dec 05, 2008
to remove the axles, remove brake caliper and disc, remove hub assembly, the center hub/axle nut and...(there are i think 3-4 bolts on the back side of the spindle to remove the hub), you may have to force the hub off the spindle with a hammer or air hammer... once the hub is out the axle should slide out of the front differential allowing access to the ball joint nuts for removal...
Posted on Jun 12, 2009
SOURCE: upper and lower ball joints
Jack the truck clear of the ground and let the wheel assembly hang. After you remove the tire place your jack under the lower control arm so it's firm. Remove the cotter pin, if you have one and loosen the big nut almost off. Wedge a "pickle fork" between the control arm and the spindle and give it a belt with a hammer until the ball joint pops. Raise the jack so you can undo the nut easily and separate the control arm and spindle.
The upper ball joint is riveted or bolted in. Grind the rivets or use a cold chisel and remove the ball joint. Clean up the area with some sandpaper, dirt , loose rust, etc.and put the new joint in. Put the spindle back on using the jack if necessary and put the nut back on and tighten.
The lower ball joint is pressed in. Tie the spindle out of the way and brace the lower control arm with some blocks or the jack if you have to. A few whacks with a hammer should pop the joint out. Clean the hole out lightly, just to remove loose rust and dirt. Put the ball joint, minus the grease fitting ,,in the hole and use the jack with a block of wood, to put it in place.You may have to fiddle with the spindle to make sure it is lined up. I've never had any trouble using a 1ton trolley jack and the weight of the truck to put the lower ball joint back in. Replace the nut and grease fitting.
The new ball joints will probably come with cotter pins, use them. Make sure the new joints are tight or they will wear the holes in the spindle. Don't forget to grease the new joints. Hope this helps.
Posted on Jul 14, 2009
Tips for a great answer:
Jun 03, 2017 | Nissan Cars & Trucks
Feb 08, 2015 | Nissan Cars & Trucks
Jan 20, 2013 | Nissan Sentra Cars & Trucks
Jul 15, 2011 | 2005 Nissan Pathfinder
Nov 15, 2010 | 2001 Nissan Quest
Jun 13, 2010 | 1995 Nissan Pathfinder
Jun 10, 2009 | 1995 Nissan Pickup
May 27, 2009 | 1995 Nissan Pickup
Nov 14, 2008 | 2004 Nissan Quest
Oct 06, 2008 | 2001 Nissan Altima
Dec 12, 2017 | Nissan Cars & Trucks
81 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: