Question about 1987 Ford Ranger

1 Answer

Right wheel fell off how do I put it back together need a schematic

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

If your wheel fell off there is no shematic that i know of however check to see if the studs are stripped if so pull the wheel ( POP-OFF THE BEARING CAP WITH A FLATHEAD SCREWDRIVER) unscrew thew wheel nut and pull the wheel (being careful not to drop the bearings on the ground ) then with an old nut or board (2 by 4) or something similar so you don't flare the stud so that it wont go through the hole. drive studs out and replace (fairly cheap). when you put the new studs in make sure that the teeth on the back of the hub line up with the teeth on the studs before you drive them in.if the whole fell off make sure that the threads on the spline (shaft) are not damaged. if so repair the threads and get new bearings . ( bearings only go in one way) and nut and cotter pin. (if you don't know that the race is any good take the hub to the auto parts store and ask the attendant at the counter) when reassembling do not over tighten the wheel nut and BE SURE TO PUT THE COTTER PIN IN AND BEND 1 PRONG BACK.

Posted on Sep 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed front end parts, front diff fell out . now back together and front wheels spinning opposite of rear wheels.


Drive it on the ground. See what happens. On a lift the tires can and do spin in opposite direction.

Nov 13, 2016 | Cars & Trucks

1 Answer

Window cable detached and window fell.


Have to replace the Broken Window Regulator

Try to put things back together,it will fall apart
in day or two

Mar 18, 2013 | 2008 GMC Envoy

1 Answer

My rear brakes on my 1988 ford ranger fell apart and i need to know what they should look like so i can put them back together


see pictures below. some are for the right and some for the left. Let me know if you have more questions.

1778fae.gif
307ec1e.gif
ffb0731.gif
4bfac33.gif

Oct 24, 2010 | 1988 Ford Ranger

1 Answer

Mirror fell off and has a spring inside. How do I put it back on right side mirror


You will probably have to replace the mirror as the retainer that holds it on is most likely snapped off and will not just snap back together.

Apr 16, 2010 | 2000 Chrysler LHS

1 Answer

Removed the 4wheel drive unit and kept it out ,installed front wheel bearing and it fell off


The front axles hold the wheel bearings together. You could take the axles apart and just put the outer part of the axle in and it should work.

Feb 25, 2010 | 2003 GMC Sierra 1500

1 Answer

I removed the tilt steering colum housing to instal a new cruise


The plastic piece goes between the steel rod and cruise/wiper lever. You will have to remove the wheel and the upper bearing housing to get it back where it goes. If you put some wheel bearing grease on it then it will stay in place during reassembly.. Good Luck

May 15, 2009 | 1986 Chevrolet El Camino

1 Answer

What caused my power steering belt to come off without breaking


Is your car the turbo charged or non tubo car. On the turbo car the power steering pump is on the front right hand side. all you need to do is put the belt back on and apply pressure til the belt is tight then tighten up the bolts that hold the power steering pump.

Feb 28, 2009 | 1997 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...