Question about Geo Metro

1 Answer

What holds the drum on? The big nut in the center of the axle?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.


    An expert who has answered 200 questions.

  • Expert
  • 221 Answers


Posted on Sep 08, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Kia Rio 2002 and I can't get the rear hub off?

Undo the big nut,put a large screw driver between crack in brake drum or disc leave nut flush with end of axle and tap the end of the axle with a hammer,if that dose ,nt work get a hub puller.

Jun 22, 2015 | Kia Cars & Trucks

1 Answer

How difficult is it to replace the rear axle seal on a 2002 jeep cherokee

it depends on which rear axle you have. on the 198 you have to remove the rear drums and remove the four nuts that hold the axle and seal in; and on the 8 1/4 you have to take off the differential cover and the center pin so that you could remove the c-clips that hold the axle in place. I have procedures for both but I need to know which one you have. the 198 requires drilling and presswork, the 8 1/4 requires a pry bar and a hammer.

Mar 25, 2013 | Cars & Trucks

1 Answer

Aisle nuts selftighting r not

If you mean axle nuts-the big nut on the axle at center of wheel-no, they are not self-tightening, just turned down real tight-about 150 ft.lbs. They are regular threaded, so to undo, turn them counter-clockwise.

Jul 12, 2012 | 1996 Dodge Intrepid

1 Answer

Unable to remove rear brakedrum 2001 focus

the drum and bearing are one unit. You'll need to remove the center cap and the axle nut. The drum will then come off with no problem.

Make sure you tighten the axle nut to the proper spec after you put the drum back on, otherwise you'll ruin the bearing

Sep 24, 2010 | Ford Focus Cars & Trucks

2 Answers

How do I take off the rear rotors on a 2003 s500? Do I need to unscrew the center big nut/bolt???

Most likely unless you can TAP -- medium blows -- on the outter edge of the rotor and it will come loose - -if not - look closely at where the nut meets the metal -- does it look like the nut is covering the rotor?

Also - ask the dealer - he will know better -

take down the vin number and ask the local dealer if there have been any recalls or service bulletins

Dec 28, 2009 | 2003 Mercedes-Benz CL-Class

2 Answers

Rear drums will not come off.

If this has the 1 ton style axles; in that the axle is removed by removing 6 or so bolts at the outboard end and the axle slides out, you have to pull the axle and then the internal retainer nut and the drum/hub assembly should slide off the axle.

Make sure you have some silicone for the axle end when you reassemble it.

May 31, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Removing lg nut from axle on driver side of 1995 Subaru Legacy

It is much easier to loosen the nut when the tire is on it and the wheel is on the ground. You need to remove the center cap to access it. With out the wheel and brakes on it you would have to find some way to hold the axle still while breaking free the axle nut.

May 18, 2009 | 1995 Subaru Legacy

1 Answer

Can't get rear brake drums off

you may have too smack them with a big hammer or you may have too pull axles and the big nut in side the drum to remove the drum

Mar 01, 2009 | 1997 Dodge Ram 3500 Club Cab

1 Answer

Saturn vue rotor removal

That is an axle nut. It only hold s the axle into the hub assembly. 130 ft/lbs. Remove the caliper. 2 15mm bolts remove the caliper. The rotor should be loose. If there are star clips on 1 or 2 lug studs, cut them off and discard. These are for initial production only.

Nov 18, 2008 | 2005 Saturn VUE

1 Answer

1990 626 Mazda rear drum brakes

This "large nut" you are talking about is holding a drum. Usually over him is a cover. Use big screwdriver and hammer to remove cover, gently strike from all sides, and when you remove it you will approach to a big nut. Pay attention that under the drum is a whole breaks sistem. After you remove the nut gently strike from the rear, from all sides (left, right, up and down). Drum will fall off.

Sep 28, 2008 | 1990 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides