Question about 2000 Daewoo Leganza

1 Answer

Driver side ball joint is broken - 2000 Daewoo Leganza

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Daewoo Master
  • 22,156 Answers

Has this vehicle had its yearly mechanical vehicle inspection??

Posted on Sep 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to I remove and replace the top ball joint on the driver side.


yea, if it's pressed in it may be cheaper to just get the whole upper control arm

Mar 18, 2015 | 1994 GMC Sonoma

1 Answer

00 eclipse big clunk on front driver side


Check lower ball joint and tie rod ends on drivers side.Sounds like it could be a worn out ball joint.

Aug 17, 2012 | Mitsubishi Eclipse Cars & Trucks

1 Answer

Drivers side upper ball joint replacement


It appears your car only has lower ball joints, the link below will take to detailed instructions on how to replace the lower ball joints.

Lower Ball Joint Replacement Instructions

Please rate my advise.

Jan 14, 2011 | 1988 Toyota Camry

2 Answers

Lower ball joint broke and i need to replace it. How do i take it off and put a new one in.(do i need a ball joint press) 98 Chevy Silverado 1500


jack up the the side with the broken ball joint under the control arm.
Remove the axle nut (4x4)
remove the caliper and the rotor.
remove the outer tie rod from the knuckle.
Remove the upper and lower control arm nuts and remove knuckle from vehicle.

Using a ball joint press remove and install the ball joint.

tighten axle nut (4x4 only) to 133 lb-ft after everything is assembled.

Nov 30, 2010 | Chevrolet Chevy Cars & Trucks

2 Answers

The front driver wheel is slanted outwards at 45 drgree


was there a huge clunk and then it seemed like the wheel fell off while you were driving? you've broken a ball joint. hopefully there was no resulting damage caused. i hope this helps and good luck!

Feb 17, 2010 | 2002 Ford Explorer

3 Answers

How many ball joints does a 99 dodge stratus have?


It has two,lower ball joints,one on each side.

Feb 11, 2010 | 1999 Dodge Stratus

1 Answer

The driver side suspension squeeks there is a lot of different openios some say ball joints some say struts anyone with similar problem and how to fix?


The squeeks would definately be the ball-joint.

I had the same problem few weeks ago till I changed my ball joint.

Replace ball joint please and rate my solution.

Good luck.

Aug 16, 2009 | 2001 Lincoln LS

3 Answers

I hear the front suspension rattle when i go over pot holes or cracks in the road. At first it was just the drivers side now i can hear it on both sides. What could this be?


could be ball joints, bad shocks, loose brake calipers or a broken coil spring although the last one would also show some sagging of the suspension.

I suspect it 's balljoints.

Aug 06, 2009 | 2003 Toyota 4Runner

1 Answer

Clunking in tire


check ball joints by lifting front end and shake tires. if loose your ball joints are bad. you will hear a clunking sound as you apply brakes during driving. its the play in the ball joint. the dealer wants $600 in labor. $160 in parts at auto zone. get the ball joint press also. good luck.

Jan 27, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

1989 oldsmobile cutlass supreme front drivers side ball joint replacement


you can buy a new lower control arm but the cheaper way out is you can buy a new ball joint for about $15 and cut off the rivits holding the old one and bolt on the new one in place with the supplied hardware hope this helps also a airhammer make quick work of rivits please rate -jeff

Aug 05, 2008 | 1989 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
2000 Daewoo Leganza Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...