Question about 1996 Dodge Ram

Open Question

Whats the torque suppose to be on an oil pump on a 96 dodge ram 1500 v6

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1997 dodge ram 1500 v6,i have a misfire,ive changed plugs,wires,distributor cap,rotor cap,fuel pump,rollover valve,coil,still has a miss

you can try changing the ignition coil, I own a 97 Dodge 1500 and mine did the same and thats what i had to do.

Posted on Oct 08, 2008

michigan man
  • 3533 Answers

SOURCE: Where is the oil sending unit on a 2002 dodge ram 1500 4.7 L?

it normally is located near the oil filter it looks like a little plug with a wire on it

Posted on Apr 04, 2009

  • 370 Answers

SOURCE: 2004 dodge ram 1500 w/4.7L overheats after water

if you got a coolant flush machine flush the system make sure there is no clogs, if you dont have this equipment you can go to a hadware store and get a high heat Tee with a hose end on it and a cap for when your done, dont forget some hose clamps.
now look for the heater return line from the heatercore and cut into it and place yout hose tee there and clamp it in place, put your water spiket on and use a vise grip to pinch the hose to force the water one way or the other, then once you get water coming out of your overflow tank (im assuming this dadge doesnt have a radiator cap) then take and move the visegrip to the other side and repeat the prosess. once your all done you will be able to drain the water out from the spout on the bottum of the radiator, and you should be able to put straight antifreeze in the radiator run it for a bit and recheck for the correct mixture...
good luck, also check your hoses for spongy feeling those should be replaced

Posted on Aug 25, 2009

Testimonial: "thank you for the suggestion. the radiator does have a cap, though. will this make a difference?"

  • 27 Answers

SOURCE: i need all torque specs main bearing caps

haynes manual is the best way

Posted on Oct 07, 2009

  • 15 Answers

SOURCE: what are the front axle nut torque specs for a

185 ft.lbs

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter

Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

I have 96 dodge ram 1500 half ton auto trans . the torque converter sael went out so when i pulled the seal a bearing came out to i do know i need to replace it but is pressed in or can be pushed in as in...

when this happens in my shop we change the converter, "bearing"aka(pump bushing) and the seal . in some extream cases you may need to replace the pump ..the bushing should be available and can be tapped in with a hammer and propper chisel , most transmission oriented shops would charge you 75-125.00 if you bring the unit to them to put in the bushing and seal properly , they will probably help you locate a reman converter for a reasonable price

May 09, 2011 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Firing order diagram for 96 dodge ramp 1500 van v6 3.8 engine

Note this information, about Dodge RAM 1500 have 3.9 engine... 1996 Dodge 1500 Pickup 3.9 liter V-6 VIN "X"


This is for one 3.8L V6 1996 Dodge 3.8 liter V-6 VIN "L"


Hope helps (remember rated this).

Jul 04, 2010 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Replaced front seal on my '97 Dodge Ram 1500, V6

Assembly of converter to trans and then tunit to engine? The torque converter must engage and slide into the front pump. The seal is easily damamaged if not properly fitted.Once the trans is against the engine the converter can be slid forward to bolt the flex plste.There should not be more than approx. 1/4 inch between the converter and trans bell housing if the converter is properly mated to the trans. Good Luck, Ned.

Jun 01, 2010 | 1997 Dodge Ram 1500 Club Cab

1 Answer

Oil light started flashing, changed oil and light went out, but now when car is warm and at idle it will come on and go off when i acclerate

i just changed a 96 dodge ram 1500 oil pump i had the same systoms there is trash in the oil sreen pump it will come on when u give the gas an bottom out when u let off

Dec 12, 2009 | 2005 Dodge Magnum

1 Answer

I need the 96 dodge ram 1500 rod bolt torque specifications


Nov 04, 2009 | 1996 Dodge Ram

1 Answer

Oil pump

remove oil pan from engine..oil pump is bolted to rear main bearing cap of engine..pickup tube may be plugged if you're having an oil pressure issue

Mar 24, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides