Question about 1999 Chevrolet Malibu

1 Answer

My 1999 Chevy Malibu wiper will only work on the hight speed. The intemitten and low speed does not work. I have checked the fuses and they are all good.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 228 Answers

The only other thing left is the switch,or the intermitent part of the circuit board on the wiper motor assy. Check the plug in connection,and the motor by tapping on the motor while on the lower speeds setings. Does the wipers park correctly when turned off??

Posted on Sep 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

2 Answers

2003 chevy suburban windshield wiper do not work in low speeds, but in hight speed


Have someone check the connections from the harness connector to the wiper control board to see if the solder joints have deteriorated. Might need to be re-soldered.

May 04, 2014 | 1999 Chevrolet Suburban

2 Answers

Windshield wipers work on high only 03 malibue


Most likely the cause of this is because of the switch not operating properly. The wiper switch circuitry has 3 different diodes. One for high, one for low, and one between the 2 relays that run the motor. One relay turns the juice on and the other determines if it's high or low speed. On/off is relay 39, high/low is relay 40. You'll find them under the hood. Lift off the battery cover, then the fuse block cover. On the underside of the fuse cover is the location legend. The diode is #27. Check it for pass/no pass with a small light while unplugged from the circuit. Also try swapping the two relays with each other. This will determine if the problem is the switch.

Jan 18, 2012 | 2003 Chevrolet Malibu

1 Answer

My 1999 chevy malibu windshield wipers no longer work - I just replaced the fuses, got a new motor for the wipers and a new electrical harness and the windshield wipers still dont work what could the...


with the switch on, do you have power at the motor! if there is no power then switch has to be bad. have a good day ! it pretty much has to be the switch. Just buy one from your local auto parts place, and if it doesnt fix it just take it back and get your money back smile.gif . have a good day !!

Jun 07, 2011 | 1999 Chevrolet Malibu

1 Answer

Have a 2005 Chevy Malibu Maxx, the window wipers are not working, I replaced the control switch in the dashboard, still not working, mechanic say the the problem could be in the fuse box, any other...


ITS A FUSE OR RELAY RUN JUMPER WIRE FROM POSITIVE SIDE OF BATT. AND PUT IT TO WIPER MOTORIF IT COMES ON REPLACE FUSE AND RELAY...GOOD LUCK ...B.HARRIS A.S.E. CIRTIFIED 25 YR. EXP.

Apr 30, 2011 | 2005 Chevrolet Malibu Maxx

1 Answer

On my 99 jetta My headlights don't turn on only the driving orange lights and the hight beams work but there is only one bulb for both? And my wiper lever doesn't work the wiring is all messed up and...


have you checked the fuse for the head lights? it only has one bulb for both low and high beams, so it could be the low beam fuse that went out, and if not replace the light bulbs, but make sure you check the fuses first.. good luck!

Apr 15, 2011 | 1999 Volkswagen Jetta

1 Answer

The windshield wipers on my 1999 Chevy Malibu no longer work. It's very cold and snowy here. They made a jerky motion at first and now no longer work. Thank you.


I would say that the wiper motor arms have jumped off and you have to take the rill right under your windshield off and snap the wiper motor arm back on to the wiper motor and then put the grill back on there and then you are all set to use them again.

Jan 22, 2011 | 1999 Chevrolet Malibu

4 Answers

Windshield Wiper Not Working Properly


Well sure enough all I had to do was replace the circuit board...wish I had done this a couple months ago...it was so easy to do and will now be much easier to drive with being able to see clearly again....

Dec 22, 2008 | 1999 Chevrolet Suburban

2 Answers

2000 Chevy Malibu wiper delay and intermittent won't work.


I had this problem (wipers only work on high) with my 2002 Chevy Malibu and had to replace the 6 amp diode (22059733) on the wiper control board. It is connected to the back of the wiper motor and is held on by 3 torx screws.
Radio Shack has them for $2.75 6A, 50V Rectifier Diodes (4-Pack) Model:276-1661

Dec 11, 2008 | 2000 Chevrolet Malibu

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

355 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...