Question about 1994 Honda Civic

3 Answers

Brakes are going to the floor most of the way checked rear brakes and they are still good bleed them and problem still there

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 193 Answers

Normally when the brake pedal goes almos to the floor it is an indication of low brake fluid. Low brake fluid is an indication that front and/or rear brakes are wearing. As the brake pads wear down more brake fluid will be required in the wheel cylinders or calipers. Hint, the front brakes usually wear much faster than the rear due to the fact that the fronts due a much greater braking function that the rear. Check the front pads. Don't let them get down to the metal scraping metal stage before you change them out. This causes unnessary damage to the rotors. Look at your master cylinder on the firewall under the hood in front of the steering wheel. If the fluid level is belowhte "max" mark add fluid. Low fliud should also show as a red "brake" light on your dash, but not always.

Posted on Sep 08, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 2,899 Answers

Sounds like a bad or empty Master cylinder or slave brake system leakage . Check the master for full brake fluid. Look for leaks at each wheel.
Maybe the system has to be bled.
Hope this helps.

Posted on Mar 14, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,297 Answers

You either have air in the system or your master has failed unless you see an obvious leak and/or replaced a line recently

assuming you did not install calipers recently and installed them upside down, then its time to replace the master

Posted on Sep 08, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: ive got good brakes.checked fluid got plenty but

BLEED THE BRAKES....

Posted on Jun 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Left rear wheel cylinder no pressure when bleeding.


you should check your brake line it may have gotten pinched.

Jun 03, 2015 | Cars & Trucks

1 Answer

1998 nissan altima brakes to the floor


Still air in system, sounds like the master cylinder has ran dry during the bleeding process, pumping more air into system. The lines running to the rear brakes are long, so you must bleed the fluid out the bleed screw in the rear 10+ times each side. Bleed, bleed, and bleed some more, keep bleeding untill that pedal feels good.

Dec 08, 2013 | Cars & Trucks

2 Answers

03 F150 spongey brakes after replaceing brake cylender and bleeding brakes?


This sounds like a bad brake line, these trucks are famous for rotted lines behind gas tank, make sure there are no leaks, this sounds like a leak or a defective master cylinder, if this is the same problem then i would say it is a line also check the rear brakes for leaking wheel cylinders unless you have rear disc brakes, check calipers for leaks.

Take a good look at brake system for leaks, hold brake pedal a few times and let is sink to floor , do it about ten times and then look for a leak, good day

Jun 24, 2012 | 2003 Ford F150 Regular Cab

4 Answers

Brake pedal to floor have replaced brake pads and master cylinder


Did the pedal go to the floor beforehand? Was the master cylinder leaking, and did you bleed it properly? If the master cylinder was not leaking, check your brake lines going to the rear wheels.

Jan 29, 2011 | 2000 Chevrolet Blazer

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

My brakes are going all the way to the floor of the vehicle. I have a new brake line and My brakes are still good.


try bleeding you brakes,go from rear to front,check rear wheel cylinders also.











TIM............

Oct 22, 2010 | 1992 GMC Sierra

1 Answer

I am having a problem bleading my 2000 grand pris brakes. check all the brake line no leaks but when i bleed the brabe pedal coes to the floor. i have also bleeb frunt to rear and rear to frunt.


This is a two person job. You have one push the brake pedal to the floor and hold it there. Then the other opens the bleed valve until brake fluid comes out. Close the bleed valve and have the other person release the brake pedal. Repeat. Continue doing this on each brake bleed valve until there is no more air coming out of the lines at each bleed valve just a solid stream of fluid. Fill master reservoir back up with brake fluid as needed through the process. You bleed from farthest to closest meaning from rear to front.

Aug 04, 2010 | 2000 GMC Sierra

1 Answer

I have a 97 jetta and when i try and bleed my brakes i start on the passenger side bleeder valve. and when i start bleeding the brakes i have pressure and the pedal goes to the floor but when i bleed the...


When bleeding you start at the rt rear to left rear to rt front to left front always checking to make sure master stays with fluid, also start by removing one bleeder at a time and make sure the hole is clean and free of dirt brake clean should flow through, do this to all 4, then have someone pump pedal 3 times and hold then open bleeder when you close bleeder tell them pump again three times, do this all around until you have a good pedal, also check for leaks after bleeding, may have bad rusted line or bad master but bleed each wheel good first.dont worry about pedal going to floor everytime, just make sure fluid flows out of all bleeders when bleeding. hope this helps.

Jul 26, 2010 | 1997 Volkswagen Jetta

1 Answer

Bleed the brake lines


start at the passenger rear tire, have someone PUMP up brakes and hold pressure on them, release pressure by locating small bleeder screw, loosen screw 1/4 turn, brake fluid/air should come out, after brake petal reaches floor tighten bleeder, repeat process until only brake fluid comes out. go to driver side rear repeat, go to pass. side front repeat, go to driver side front repeat, after each bleeding make sure you check brake fluid in reservoir.

Sep 24, 2009 | 1984 Ford Mustang

1 Answer

SOFT BRAKE PEDAL ON MY DAEWOO


MAKE SURE THE ARE NO OTHER LEAKS.IF U DID NOT BENCH BLEED THE MASTER CYLINDER BEFORE U PUT IT ON U PROBLEBLY HAVE AIR IN THE SYSTEM.BLEED THE MASTER CYLINDER AT THE LINES THAT COME OFF OF IT.THEN U NEED TO BLEED THE REAT OF THE BRAKES IN THIS ORDER.RIGHT REAR,LEFT FRONT,LEFT REAR.RIGHT FRONT.WHEN BLEEDING THE BRAKES WAIT 15 SECONDS BETWEEN PUMPS OF THE BRAKE PEDAL.IF U GO TO FAST U CAN DAMAGE THE MASTER CYLINDER.GOOD LUCK

May 01, 2009 | Daewoo Leganza Cars & Trucks

Not finding what you are looking for?
1994 Honda Civic Logo

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...