Question about GMC Sierra 1500

1 Answer

Want to bleed breaks on a 1991 gmc 4x4 truck, do I start on the front passanger side?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Always start with the closest to the master cylinder and then so on. Then go around again.

Posted on Sep 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the sparkplug firing order for GMC Sierra pickup truck with a 5.7 liter engine


1-8-4-3-6-5-7-2

Driver side cylinders, starting at the front of the engine, are 1,3,5,7

Passenger side, starting at the front, are ,2,4,6,8

Hope this helps.

Feb 24, 2015 | 2003 GMC Sierra 1500

1 Answer

Front passanger side of my 1991 nissan pathfinder is leaking brake fluid behind the tire what do i do?


check if the fluid is from a hose (replace) or from the caliper unit (replace it). Check that the bleed nipple is tight.

Nov 30, 2013 | Cars & Trucks

1 Answer

What is the engine size on a 1991 gmc sierra 2500 4x4


That year you probably have a 5.7 or 5.0 motor. You can find the engine size by getting your VIN and calling the dealer. They can tell you from either the 8th or 10th number in the VIN

Jan 29, 2012 | 1991 GMC Sierra

1 Answer

I replaced the rear passanger wheel cylinder on my 2000 ford taurus and bleed the breaks from right rear to front drivers side and still have no breaks why


was the wheel cyl leaking? make sure there are no other leaks anywhere i see rusted out line on these a lot check down left side of undercarage fuel lines and brake lines run along there .if you have abs you should only have to bleed rears the front are on different valves no air can get in from a rear leak.If no leaks anywhere master cyl most likely

Nov 30, 2011 | 2000 Ford Taurus

1 Answer

Changed brake pads and now I have no brake pressure


you may need to bleed your breaks so check your fluid and have a friend help you with this.. open or take off break fluid cap and top off with fluid leave cap off and start on the back passanger side break have someone pump the break a few times and then hold down on the break pedal while you open the bleeder valve when the break pedal reaches the floor hold there and retighten the bleeder valve and repeat untill no air only fluid comes out, then move to the driverside rear wheel and repeat,next is the front passanger side wheel then finaly front driverside wheel. check fluid in master cylender after every 2 trys on each wheel to make sure pleanty of fluid is in resourvior so your not putting air in the lines.. you should see a video on this to make sure you understad it fully before attempting yourself, go to youtube videos and watch a video on how to bleed breaks almost all break systems are the same. i hope this helps.

Jul 24, 2011 | 2000 Mitsubishi Mirage

1 Answer

Front line blow, replaced line master cly to abs block and from abs to right front wheel. bleed have very low and soft paddle.on 03 gmc 2500 hd 4x4. did not put all the turns and bends back in line does...


Ok here is what you have to do. First off make sure your master cylinder is full, Second your vehicle must be running when you bleed brakes that is equiped with ABS this allows the ABS pump to to run you must bleed both front brakes starting at the passenger side wheel then moving to the drivers side. It will take quit a bit of bleeding and be sure to keep checking fluid level in master cylinder well bleeding. Just remeber the vehicle must be running while bleeding the brakes.

May 12, 2011 | Chevrolet 2500 Cars & Trucks

1 Answer

I need to blead my brakes lanes the car need to


car off but always start to blead furdest away first it passanger rear then driver rear and front passanger and last is front driver side

Jun 12, 2010 | 1991 Buick Century

3 Answers

Break bleeding


try bleeding the brakes as a system. start by making sure the master cylinder is full. then have a Friend step on the brakes and release 3-5 times. the last one they should hold as you break lose the bleeder on the passenger side rear, then do the driver side rear ,(check fluid) next passenger front and then the driver side front do each wheel until you don't see any or hear any air, thats the way i have always bleed brake systems. hope this helps

Feb 05, 2009 | 2004 Dodge Ram 1500

1 Answer

Changing Brakes


you will need to bleed the brakes once you are done to get the air out of the lines.
if you need help chaing them please comment back. also you will have to bleed the breaks in a certain order.
start at the passanger side rear than move to the drivers side rear than the passangers side front than the drivers side front.

Aug 03, 2008 | 2005 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...