Question about 1994 Oldsmobile Cutlass Supreme

1 Answer

We bought a 1994 Oldsmobile Cutlass Supreme Convertible 3.4 to fix up for my step daughter. The rear quarter windows have a rubber seal at the bottom of the windows on the outside of the car, which keeps water out. Ours is weathered and cracked and badly needs replaced. I don't know what this rubber seal is called nor do I have a part number, so finding it so I can order it is impossible. What is this rubber seal called and possibly what is the part number?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Oldsmobile Master
  • 586 Answers

These are called belt weather or sealing strips. I think the parts you are looking for are 12503936 and 37, but they are discontinued parts. Good luck finding them - try auto wreckers (online search).

Posted on Jun 14, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 142 Answers

SOURCE: 1991 oldsmobile cutlass supreme

Check for fuses/power/ground to the engine computer (or injector drive computer) whatever the case is.

Spark, fuel pump, and starter all are independant of the fuel injection computer.

Either the computer itself has gone bad, or it is not receiving power or ground, or wiring to the injectors might be bad...

Posted on Aug 28, 2008

  • 1 Answer

SOURCE: 1998 Oldsmobile Cutlass Supreme Blower Motor

It's not to hard to do, just have to lay upside down in your pas. floorboard, remove plastic panels under gloove box with small nut drivers,(can't remember size) then there are three hex head screws holding on the blowerplus the wireing connector, anf it has a wierd rubber gasket, hope this helps.

Posted on Sep 12, 2008

machinehead2
  • 14 Answers

SOURCE: 1994 oldsmobile cutlass supreme will not start.security flashes

Sounds like a RFID issue. Your key most likely has a chip inside of it. Most of the time people will have multiple keys on their key chain that can cause interference with the receiver in your steering column. Try using the one ignition key to start.

Posted on Jan 10, 2009

  • 564 Answers

SOURCE: 1994 oldsmobile cutlass supreme sl the fuse box for signal lights

the fuse box will be in 1 of 3 places (1)glovebox (2)under dash by drivers foot kick panel or (3) under hood .

Posted on Nov 22, 2009

arauzvictor1
  • 466 Answers

SOURCE: 1986 Oldsmobile Cutlass Supreme vacuum hose

Ok sent you this the engine you have to specify that engine has to help you. Thanks2c36ea6.jpg

Posted on Mar 24, 2010

Testimonial: "good job getting info. and real quick too"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location for map sensor on a 1994 oldsmobile cutlass supreme 3.4 DOHC?


It's mounted in the right rear notch of the air intake by the fire wall or on the fire wall in that general location. with a vacuum line attached. That is standing in front of the car at the rear top edge of the manifold. Look it up on parts geek you can look at the enlarged picture to see what yo are looking for.

Jul 28, 2016 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Where are the brake fluid resevoirs on the 94 olds cutlass supreme


I take it you have the 3.4 L (204 cu in) LQ1 V6 engine.


I've seen it before. If that's the one ' remember seeing it on the peripheral of the engine compartment at the rear, I think. Dirty compartments don't always show a reservoir, but look for the telltale rubber lid or a metal one with a thick wire clamp.

Feb 07, 2013 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Where is the fuel pump relay located


1994 Oldsmobile Cutlass Supreme 3.1L SFI OHV 6cyl the Relay - Fuel Pump is located under hood, passenger side, front engine area, rear of headlight housing, mounted in relay block on upper fenderwell.

Remember rated this. Good luck.

Aug 10, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Were do I find the control module for the automatic door locks.


hi the module is behind rt side of dash but these cars have a history of the master switch [driver door] going bad causeing slow or no opperation hope this helps don

Jun 24, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Is it difficult to fix the rubber seal(it is leaking fluid) around the piston on a 97 olds cutlass supreme rear brake caliper?


It is probably just as easy and just as cheap to replace the caliper itself then tearing it apart to fix the seal.

Dec 15, 2009 | 1997 Oldsmobile Cutlass Supreme

2 Answers

1994 oldsmobile cutlass supreme sl the fuse box for signal lights


the fuse box will be in 1 of 3 places (1)glovebox (2)under dash by drivers foot kick panel or (3) under hood .

Nov 21, 2009 | 1993 Oldsmobile Cutlass Supreme

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Trying to start a 1994 Olds Cutlass Supreme and wont turn over.


Does it crank at all or is there nothing when you turn the key? If the resistor chips in the key(s) are bad, they shut down the fuel system for 3 minutes and it won't crank. I've had this happen and the problem was solved when I got new keys.

Jan 08, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

1994 cutlass supreme--security light on--car won't start


take to dealer and have them reprogram the computer

Jun 23, 2008 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...