Question about 1993 Chevrolet S-10

Open Question

How to replace the rear main oil seal on a 1993 chevy s-10 pickup 2.8L v6

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: Rear Main Seal Leak

THat seems to be in the ball park. If you have an AWD, the flat rate time is 14.4 hours. If you have just a FWD, it is 9.5 hours. In either case, the transmission has to be removed from the vehicle to access this seal. Sorry.

Posted on Sep 09, 2008

  • 234 Answers

SOURCE: rear main seal leaks..does this affect transmission??

A leaking rear main seal will not cause your transmission to leak.

The transmission has its own seal and should not leak because of the engine rear main seal.

Due to the labor involved in replacing the rear main seal on the engine, it is best if you replace the front transmission seal at the same time if possible.

Installation varies on different vehicles but the principles are the same.

Posted on Apr 15, 2009

  • 23 Answers

SOURCE: instructions on replacing rear axle end oil seals 90 silverado pu

Where's it leakin?

Posted on May 12, 2009

  • 3600 Answers

SOURCE: rear main seal

I have done many the transmisson has to come out to replace it but your price is way out of line, should not be more than $400.00 give me a zip and I can get you a certified shop that can do it for less with a warrenty.

Posted on Aug 08, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you replace rear main oil seal on '93 Chevy S-10 pickup?

Remove trans, remove flywheel, remove and replace seal.

Apr 14, 2015 | 1993 Chevrolet S-10

1 Answer

Oil leaking from toyota camry 1992, 1994 model

You don't say what engine it has. The 4-cyl was a better than the V6 for oil leaks.

The V6 had oil leaks from

-rear bank cam cover gasket

-distributor o-ring seal

-oil filter bracket o-ring seal

-crankshaft nose oil seal (less common)

-rear main bearing oil seal (expensive, just leave it)

The 4 cyl leaked oil from

-distributor o-ring seal

-camshaft cover gasket

-rear main bearing seal (expensive, leave it)

May 21, 2012 | 1991 Toyota Camry

2 Answers

What would cause an oil leak at the rear of my 2003 Chevy S-10 With 2.2L eng.?

oil pan / rear main seal / head / valve cover
more then likely rear main

Jun 26, 2011 | 2003 Chevrolet S-10

1 Answer

Chevy S-10 Pickup Oil Leak

You sure the oil comes from the plug and doesnt just run down from above and drip of it? Clean aroun the area and take a drive look again and make sure its not cming from anywhere else. If its the plug, you just need to replace the washer on the plug next time you oil change. do not try to just tighten the plug. If you buist the thread in there that an expensive repair. It should not be very tight as the washer should seal it.

May 26, 2010 | 2000 Chevrolet S-10

2 Answers

I need to replace the rear main seal on my 95 chevy pickup with a 350. do i need to drop the tranny?

Yes, either pull the trans or pull the engine. No way to get in there with out having one of the two out!
FYI it's very rare for a rear main on that engine to leak, Most all of the time it's the oil pan gasket or coming from higher up like a valve cover or the intake gaskets!

Oct 21, 2009 | 1995 Chevrolet K1500

1 Answer

1989 Toyota PickUp Truck V6 4x4 Any sealants or caulking type seals to put around very bad leak around the transfer case and the rear main seal?

there is no way to fix a rear main leak except to replace it, sorry but if there was a way to jerry rig this every tech would use it.

Jul 27, 2009 | 1989 Toyota Pickup SR5

1 Answer


cam caps 10Nm(89lb in)
head bolts 64Nm(47lb ft)

mains 39 Nm
oil block 1st step 29Nm(22lb ft)
2nd step 55-65deg
crank case side bolts 39Nm
here is lay out of sequence of bolts to be done all at once.
21 22 23 24 side bolts
2 4 6 8 mains
14 10 11 15 oil gallery
13 9 12 16 oil gallery rear of engine
1 3 5 7 mains
17 18 19 20 side bolts

Jul 11, 2009 | 1993 Isuzu Trooper

1 Answer

Oil leak in rear main area and I have already replaced it

Have you replaced the rear main seal? What bout the housing that holds the seal, it'a an alu casing and it might hava a crack? The crankshat rear part where the seal goes could have a deep groove as well.

Mar 27, 2009 | 1993 Nissan Pathfinder

Not finding what you are looking for?
1993 Chevrolet S-10 Logo

Related Topics:

625 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides