Question about 1996 Toyota RAV4

1 Answer

How do you replace clutch in 1996 rav4 - 1996 Toyota RAV4

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

There are a lot of steps involved in this to do it correctly not counting the obvious, you have to pull the transmission. I recommend you get the Haynes or Chiltons Repair manual on your vehicle for step by step directions and recommendations on tolls, special or otherwise. The new assembly should come with any guides, that is a bearing guide or clutch alignment guide, that might be needed.

Posted on Sep 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjusting clutch on rav4 1996


Hi Cliff, The adjustment of the clutch is carried out at the top of the clutch pedal. You'll need to lay on your back to reach it. It uses a 12 mm locking nut. if the pedal is too high, screw the push rod in and if its too low, unscrew. Regards John

Jul 20, 2013 | Cars & Trucks

1 Answer

How to replace clutch step by step on a toyota rav4 4wd


You need some very specialized tools to do that You'll need a jack to hold the transfer case once you remove all the bolts holding it to the transmission. Remove the drive shafts.Then you'll need to remove the transmission, again with a supporting jack. Once that has been accomplished , remove the bolts holding the clutch to the flywheel. I'd replace the pilot bearing in the flywheel that holds the input shaft to the gearbox before proceeding. There are special tools available to do that. Now assemble the clutch disk and the clutch plate and put the bolts back in without tightening them. Now take the clutch alignment tool and push it thru the clutch disk and into the new pilot bearing. position it so the clutch disk is dead center in the clutch plate and then finish tightening the bolts Put a new throw out bearing on the clutch release lever and reinstall the transmission and transfer case. Reinstall the drive shafts and replace any gear oil that may have spilled out of the transmission or transfer case. Adjust the clutch pedal clearance to spec and you're done.

Mar 30, 2013 | 1996 Toyota RAV4

1 Answer

Why my 1996 rav4 has no power


The carb clutch is slipping.LOL:

Oct 28, 2012 | 1996 Toyota RAV4

1 Answer

Can I add something other than brake fluid (maybe a brake treatment that is heavier) to the brake fluid to help keep the clutch from slipping on a 1996 rav4


no, the hydraulics is not the issue, its time to replace the clutch. there is no quick fix or easy patch job, replace the clutch (hydraulics dont affect how the clutch holds, they mearly either disengage the clutch or do nothing)

Mar 13, 2012 | 1996 Toyota RAV4

1 Answer

LOCATION OF 1996 RAV4 THERMOSTAT FOR REPLACEMENT


It is at the engine end of the upper radiator hose. In the picture below it is number 15, below the thermostat cover, number 13 and gasket, number 14. This is a picture of your 1996 Toyota RAV4 cooling system.




gcs_la_0.gif

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Jun 02, 2011 | 1996 Toyota RAV4

1 Answer

Noticed that the revs would build too quickly and did not match the 2004 Rav4 speed in higher gears. 1st gear seems OK. If I accelerate gradually there are no problems. So I'm guessing I need my clutch...


You are exactly right. The clutch is going out. The cable is an automatic adjusting cable. So there is no adjustment. It will require a new clutch.

Jan 24, 2011 | 2004 Toyota RAV4

1 Answer

Slipping clutch


This is very technical, let an expert handle for you before something else goes wrong. Fix the clutch fast. I use the same car. I love the car.

Rate this please....

Mar 21, 2009 | 1996 Toyota RAV4

Not finding what you are looking for?
1996 Toyota RAV4 Logo

Related Topics:

823 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...