Question about 2002 Ford Crown Victoria

Open Question

Replace 2003 Crown Vic gas door button on driver side door.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 178 Answers

SOURCE: 2003 ford crown vic hard steering

i would have to say to check for a relay in your fuse boxes for power steering pressre switch or it may have its own police pkgs have a lot of relays due to all the extras

Posted on Sep 11, 2008

BPALepine
  • 61 Answers

SOURCE: door panel

Depends on what door trim you are trying to replace. If you are trying to replace the door trim on the front doors you need to remove two screws from behind the casing around the door handle and then remove a screw from the bottom left of the door and then there will be a screw on the left of the door as high as the arm rest on the door. Finally pull up on the door panel and out to remove the panel. Remove the harnesses and you are complete.

If you are trying to remove the rear doors you need to remove a screw from the bottom of the door again near the left side then remove the screw from behind the casing that surrounds the door handle. Finally pull up on the door panel and out to remove the panel. Remove the harnesses and you are complete.

Posted on Apr 23, 2009

  • 599 Answers

SOURCE: My 99 Crown Vic acts like it isn't getting gas

check for clogged fuel filter first, usually the pump works or it dosen't, check and get back to me.

Posted on May 01, 2009

  • 1 Answer

SOURCE: where is fuelpump on 2003 crown vic police intercepter

Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

Posted on May 20, 2009

  • 33 Answers

SOURCE: Replace horn on 2006 crown vic

I believe once you have mounted the horn and connected the wire you will find that the horn wire was cut at (by) the steering coloum that the siren override was hooked to,you will have reconnect this,I hope this helps you

Posted on Jul 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2007 crown victoria driver side window wont go up or down what's the problem ?


if it is electric window check fuse box or the window motor or the connections or switch

Jan 24, 2016 | Cars & Trucks

1 Answer

I HAVE A 2003 CROWN VIC AND WAS WONDERING IF IT WAS EASY TO CHANGE THE FUEL FILTER AND SHOCKS ON IT AND IF SO WHAT TOOLS DO I NEED AND HOW TO DO IT IF ANY ONE CAN HELP


Fuel Filter is bolted to the frame under the right rear door. A Quick Disconnect tool is required to remove the fuel lines. Not sure of the bolt size to remove the mounting hardware.

2005 Ford Crown Vic fuel filter change

Nov 10, 2014 | 2003 Ford Crown Victoria

1 Answer

I have a 1994 crown vic and the button for the fuel door is broken how can i get the door open until i can get it fixed?


There should be a pull cable in the trunk that you can pull to open the gas door, it may be behind the carpet on the wall behind the gas door inside the trunk.

Feb 27, 2011 | 1994 Ford Crown Victoria

3 Answers

On my 2000 ford crown vic. the power door locks work except for the drivers side. sounds like something is rattleing in the door. any ideas on what and how to fix


the power lock in that door may have broke the rod. remove the door panel to inspect its operation and replace the necessary part. hope this helps

Jan 31, 2011 | 2000 Ford Crown Victoria

1 Answer

The passenger side power window on 1988 crown vic will not go up. when you push button on the drivers side or the passenger side it makes no noise at all .


check the wires inside the drivers door ,where they go from the door to the body,slice the rubber cover to see. often they will break from the drivers door being opened and closed so many times.

Sep 05, 2010 | 1988 Ford Crown Victoria

1 Answer

94 crown vic how do i find out if car has keyless entry


Easy. Does your Vic have a five number keypad above the driver's side exterior door handle? If so the you got key-less. If not, you do not.

Jun 13, 2009 | 1994 Ford Crown Victoria

1 Answer

2004 crown victoria lx smashed driver side window


normally you have to loosen the track and it comes out as one whole assembly stop by a dealer in the parts department and ask them to print out a diagram or show them the part you are having the problem with

Aug 27, 2008 | 2003 Ford Crown Victoria

1 Answer

2003 cvpi wing mirror


first of all if you have the new mirror off of a crown vic or grand marquise there is nothing to worry about wiring because you have to take the door panel off and once off all you have to do is plug in the new mirror the same way you took the old one off

Aug 14, 2008 | 2003 Ford Crown Victoria

1 Answer

Electric adjustment of outside mirrors


you need to pull the door off on your fuse panel scematic should tell you you may have a second fuse vpanel under hood drivers side

Aug 02, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
2002 Ford Crown Victoria Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...