Question about Mitsubishi Lancer

1 Answer

My problem in my lancer 95 is clutch. when you step on the pedal the clutch is very hard. not like before when you step on the clutch pedal you don't have to force stepping on it. can you please give me an advice. thanks, willie

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mitsubishi Master
  • 4,348 Answers

There is an assist spring that my have broken, up under the dash, if it is in place and functioning, the clutch itself is the next area to open up.

Posted on Sep 08, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to adjust 95 geo tracker clutch

you meant dis-engage im sure.
pedal up is engaged,
pedal at floor dis-engages it.
my guess, is the clutch drags unless i push the clutch pedal 100%
to the floor.
1: bad cable is 90% cause. non last this long.
2: no free play is way too loose.
3: broken lever on the pedal top. caused by #1

all fail modes covered here.

Apr 23, 2014 | Geo Tracker Cars & Trucks

2 Answers

2001 nissan pathfinder clutch mushy and clutch pedal won't return

try a different mechanic . loss of fluid is a problem that they can fix

Mar 20, 2017 | 2001 Nissan Pathfinder

1 Answer

How do i bleed the master cylinder on an 02 lancer

Check the slave cylinder on the transmission for leaks, and replace if it is. Bleeding:
1. put fluid in the master reservoir.
2. move the slave actuator shaft so the clutch release lever has not slack.
3. Have someone press the clutch pedal, and crack the slave bleed nipple to let out the air.

Once the slave moves the release lever, you'll be able to decide if the clutch is OK or not.

Oct 09, 2012 | 2002 Mitsubishi Lancer

1 Answer

95 accent hard to shift to first gear sometimes forth gear.replaced slave plus clutch pump also has new clutch kit.can the linkage be adjusted be great if you could help thanks.

Yes. You can adjust the clutch rod inside the car at the clutch pedal. loosen the 12mm jam nut and unscrew the rod 2 turns at a time and test clutch operation each time.Repeat as necessary. dont forget to retighten the jam nut. Good luck! Scott

Aug 29, 2011 | Hyundai Accent Cars & Trucks

1 Answer

When I step on clutch pedal truck comes to stop also hard to shift gears. I replaced clutch kit but not the mster slave cylinder

the clutch system is simple, master, slave ,clutch, lever,clutch.Go to the slave and get someone to pump the clutch pedal get a sm all spanner and when the person has pumped the pedal lets say 10 times tell them to hold the pedal in and dont let it out until you have opened the bleed screw and reliesed the fluid out tighten and continue until the air is out of the system what im telling you is [air] in the system work back and you will find the culpert .please rate this answer.adrian,,,,,,

Aug 23, 2010 | 2000 Ford Ranger SuperCab

2 Answers

I have a 2001 Ford Mustang, v6 3.8 5 speed manual

The clutch is not fully releasing. You can try putting it into some other gear first, then rapidly moving to first gear, but really, you need to either adjust the clutch, or get it repaired.

Jul 07, 2010 | 2001 Ford Mustang

1 Answer

How to adjust the clutch pedal

There is no adjustments for a slave cylinder is part of this clutch. It is all hydralic which means it is an auti adjustable system. Upon the time when the pedal has no pressure the slave cylinder must be relaced

Mar 21, 2010 | 2005 Mitsubishi Lancer

1 Answer

I have an 02 Mits. Lancer w/ a manual trans. Whenever I try to put it in any gear there's a lot of resistance. I pretty much have to use two hands and even then it's tough. Could this be a fluid problem or...

check hydraulics for leaks by looking at the slave cylinder on the gearbox activating the clutch fork,pull the rubber boot back (no fluid o.k)look at the clutch pedal under the dash and peel that rubber boot back(no fluid o.k)bleed it to be sure by pumping the clutch pedal,holding it down and getting someone to crack the bleeder on the slave cylinder on the gearbox,HOLD the pedal down and tighten the bleeder first before releasing the clutch pedal,otherwise air will be sucked in if you pull the pedal back first.If that doesnt work you probably need a clutch but this is more likley and check the line running from the master to the slave for leaks and tightness

Nov 28, 2009 | 2002 Mitsubishi Lancer

1 Answer

Wont go into first with out grinding or going in hard

Remove gearbox and replace the whole clutch assemberly.Problem is your thrust bearing as collapsed.Good luck.

Jul 04, 2009 | 1997 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides