Question about Jeep Grand Cherokee

1 Answer

When the headlights are turned on,the backlit light for the driver side heated seat switch doesn't come on- the indicator for heat level DOES come on when the button is pushed- can I replace the bulb responsible? The backlit light for the climate "mode" turndial is very faint- can I replace the bulb? 2006 Jeep Overland thank you Norm @ divotdoc2451@yahoo.com

Posted by on

  • divotdoc2451 Sep 12, 2010

    Thank you ledsled for a logical and understandable response! I especially appreciate your comment regarding how time consuming and difficult this fix would be-that is particularly helpful! I have one other question regarding vibration when I get between 70-75 mph. I've had all four tires balanced and rotated and then followed up with a four-wheel alignment-still occurs as before-have you heard of any specific or general conditions that may cause this issue and do you have any suggestions as to how to solve it? Have you heard of "road force balancing" and whether this is truly much more effective than "traditional" balancing techniques? I really appreciate any thoughts you might have. This is a 2006 Jeep Grand Cherokee Overland that I purchased a month ago with 78,000 miles. Sincerely, Norm

  • divotdoc2451 Oct 12, 2010

    Hi ledsled378! I went to Sullivan Tire in Falmouth Maine- they use the Road Force balancing equipment from Hunter Mfg.- this equipment has diagnostics which can indicate a bad rim and/or a bad tire. I am fortunate that all my tires and rims were good- the problem I was having with the vibration was due to improper balancing that I had done at a local company that used traditional spin balance methods. The tech at Sullivan said that all four rims were more than an ounce off (weights) than what they should have been. BINGO! Problem solved! Smooth as silk up to 80 and everything in between! Cost was just under $60 for all four tires. Service at Sullivan was excellent by the way- they have numerous locations in Maine, Massachusettes and New Hampshire. Hope this is useful info! Take care, Norm

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

The heated seat switches are both mounted in the instrument panel. The two switches are part of the lower instrument panel switch pod assembly. If either of the switches is damaged or inoperative the complete switch pod assembly must be replaced.
Each heated seat switch provides a resistor-multiplexed signal to the Cab Compartment Node (CCN). Amber Light Emitting Diodes (LEDS) in the top portion of each switch indicate the level of heat in use: Two LEDs are illuminated for high, one for low, and none for off. Pressing the switch once will select high-level heating. Pressing the switch a second time will select low-level heating. Pressing the switch a third time will shut the heating elements off.
The LED indicator lamps in each heated seat switch cannot be repaired. If the LED lamps are inoperative or damaged, or the switch is inoperative or damaged the complete switch pod assembly must be replaced.
Rmoval of the front instrument panel as well as the shift plate bezel will be required. This is NOT an easy job, and to be perfectly honest, I would ignore the LED light(s) that are out, or at least wait until more LED's burnout before attemping this very time consuming procedure.

Posted on Sep 08, 2010

  • 2 more comments 
  • GetMeOttaHere Sep 12, 2010

    As for the vibration. I suspect a tire or slightly bent rim is the cause. I'm assuming that when the Tech placed the tire and rim on the balancer, they also checked for an uneven rotation. This would indicate a bent rim. Taking this out of the equation, I suspect a tire that has an internal belt (wire weave) that has pulled away from itself Internally, and causes this vibration at higher speeds. This is just a hunch.

    I also own a Grand Cherokee 4x4 that is also, as we know, all wheel drive. And it does have what I call the 70 MPH hummm. What I am experiencing is the drivetrain, not really a vibration, but it is noticeable humm to the ear, than actual feel. Just thought I'd mention this.

  • GetMeOttaHere Sep 12, 2010

    I'm not familiar with Road force balancing, nor have I heard of such. Seems like a term used when running larger rims and tires on a vehicle.

  • divotdoc2451 Sep 16, 2010

    Hi again ledsled378! I really like your replys and suggestions first of all! Road Force balancing utilizes Hunter Mfg. balancing equipment- from what I've read, it's a machine that applys a force (pressure) to the wheel surface just as if it were on the road itself- supposedly gives a more "realistic" reading and will indicate whether or not you have bad a bad rim and /or tire that conventional balancing won't provide. My Jeep Grand Cherokee Overland 2006 has more than a hummmmmm, it actually will vibrate the passenger seat @ 70-75 mph. I will have the balancing done with the Road Force technology which claims to have the ability to detect a bad rim and/or tire and go from there. If you would like, I would be happy to let you know the results. Additionally, I understand the problem could involve harmonics and drive train issues. I'll keep you posted if you'd like. Take care, Norm

  • GetMeOttaHere Sep 16, 2010

    Excellent, I'll wait to hear back from you with the results.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to find fuse boxs


FUSE PANEL LOCATION
The fuse panel is located in the engine compartment. A label on the inside of the cover lists the fuse amperage and circuits protected.
volvo 850 fuses fuse panel layout service repair manual
FUSE PANEL IDENTIFICATION
Fig. 1: Fuse Panel Identification
Courtesy of Volvo Cars of North America.
WARNING: Always disconnect battery ground cable before servicing "high-current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician.
* 1 - 15 Amp
Fuel Injection, Distributor Ignition, Automatic Gearbox
* 2 - 15 Amp
Fuel Pump, Alarm System
* 3 - 10 Amp
Courtesy Lights, Oil Level Sensor
* 4 - Not Used (1993-95)
* 4 - 10 Amp (1996)
Electronic Start Inhibitor (Immobilizer)
* 5 - 30 Amp
ECC Blower (Speed 4)
* 6 - 25 Amp
Central Locking System, Alarm
* 7 - 15 Amp
Audio System (Amplifier)
* 8 - 25 Amp (1993-95)
Power Antenna, Trailer Connector
* 8 - 40 Amp (1996)
Electronic Start Inhibitor (Immobilizer)
* 9 - 30 Amp
ABS, Traction Control System
* 10 - Not Used (1993-95)
* 10 - 15 Amp (1996)
Heated Rear Seat (If Equipped)
* 11 - 30 Amp
Heated Rear Window & Side Mirrors
* 12 - 10 Amp
Brake Lights
* 13 - 15 Amp
Hazard Flashers, Headlight Flashers, Alarm
* 14 - 30 Amp
ABS, Traction Control System
* 15 - 10 Amp (1993-95)
Audio System, Courtesy Lights, Door Open Light, Trunk Light, Glove Box Light, Remote Control Central Locking System,
Oil Level Sensor, Seat Belt Reminder
* 15 - 10 Amp (1996)
Audio System, Courtesy Lights, Door Open Light, Trunk Light, Glove Box Light, Remote Control Central Locking System,
Oil Level Sensor, Seat Belt Reminder, Data Link Connector
* 16 - 30 Amp (1993-95) Accessories
* 16 - 30 Amp (1996)
Power Antenna, Trailer Connector, Accessories
* 17 - 10 Amp
Key Reminder
* 18 - 25 Amp (1993-95)
Heated Front Seats, Power Mirrors
* 18 - 15 Amp (1996) Front Fog Lamps
* 19 - 15 Amp
Left High Beam Headlight
* 20 - 15 Amp
Right High Beam Headlight, High Beam Indicator
* 21 - 15 Amp
Left Low Beam Headlight
* 22 - 15 Amp
Right Low Beam Headlight
* 23 - 10 Amp
Left Parking Light, License Light
* 24 - 10 Amp
Right Parking Light, Bulb Failure Warning Sensor
* 25 - 10 Amp
Rear Fog Lamps, Fog Lamp Indicator
* 26 - Not Used (1993-95)
* 26 - 25 Amp (1996)
Heated Front Seats, Power Mirrors
* 27 - 15 Amp
Back-Up Lights, Turn Signals
* 28 - 10 Amp
Cruise Control, Heated Rear Window, Seat Belt Reminder Light, Shiftlock, Bulb Failure Warning Sensor, Heated Rear Seat
* 29 - 15 Amp
ABS, Traction Control System
* 30 - 10 Amp
Cigarette Lighter
* 31 - 25 Amp
ECC, ECC Blower (Speeds 1-3)
* 32 - 10 Amp
Audio System, Remote Controlled Central Locking System
* 33 - 15 Amp (1993-95)
Power Seats, OBD Test Socket, Tailgate Washer/Wipe (Wagon)
* 33 - 15 Amp (1996)
Power Seats, Tailgate Washer/Wipe (Wagon)
* 34 - 25 Amp
Windshield Wiper/Washer, Horn, Headlight Washer/Wiper
* 35 - 10 Amp
Instrument Lights, Sun Roof, Traction Control System
* 36 - Not Used
* 37 - Circuit Breaker
Power Windows, Power Sun Roof
* 38 - Not Used
* 39 - Circuit Breaker
Drivers Power Seat
* 40 - Circuit Breaker
Passengers Power Seat
RELAY PANEL LOCATION
The relay panel is located at the left corner of the instrument panel.
i copied this off a volvo site Hope this helps

Oct 10, 2016 | Volvo 850 Cars & Trucks

2 Answers

Trying to find which fuse is for the heated seats on a 2004 ford explorer sports trak


Heated Seats
This system allows the electrical heating of the front seats on passenger demand.
The components of the system are:
  • the seat heating elements located in the seat cushion and backrest.
  • the heated seat control switch, located on the seat side trim panel.
  • temperature sensors located in the seat cushion heating elements.
  • heated seat relay.
Do both front seat heaters not work ? Do you know how to test electrical circuits with voltmeter ?
PINPOINT TEST J: THE HEATED SEAT IS INOPERATIVE Test Step Result / Action to Take J1 CHECK HEATED SEAT SWITCH OPERATION
  • Key in ON position.
  • Press the heated seat switch on the driver and passenger seats.
  • Are both heated seat switch indicators illuminated?
Yes
If both indicators illuminate, Go To Pinpoint Test K . If only one indicator illuminates, GO to J5 .

No
GO to J2 . J2 CHECK THE HEATED SEAT RELAY CIRCUITS
  • Key in OFF position.
  • Disconnect: Heated Seat Relay C3250 (located under the driver seat).
  • Key in ON position.
  • Measure the voltage at heated seat relay C3250-86, circuit 1003 (GY/YE), harness side and ground; and between C3250-30, circuit 566 (DG), harness and ground.
    s5r~tr~en~file=a0078817.gif~gen~ref.gif
  • Are the voltages greater than 10 volts?
Yes
GO to J3 .

No
REPAIR inoperative 1003 (GY/YE) or 566 (DG) circuit. TEST the system for normal operation. J3 CHECK HEATED SEAT RELAY GROUND CIRCUIT
  • Key in OFF position.
  • Measure the resistance between heated seat relay C3250-85, circuit 57 (BK), harness side and ground.
    s5r~tr~en~file=a0078818.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to J4 .

No
REPAIR circuit 57 (BK). TEST the system for normal operation. J4 CHECK THE HEATED SEAT RELAY
  • Install a fused jumper lead between heated seat relay 3250-30, circuit 566 (DG), harness side and heated seat relay C3250-87, circuit 1064 (YE/LB), harness side.
    s5r~tr~en~file=a0078819.gif~gen~ref.gif
  • Do both heated seat indicators illuminate when pressed?
Yes
INSTALL a new heated seat relay. TEST the system for normal operation.

No
REPAIR circuit 1064 (YE/LB) to switches. TEST the system for normal operation. J5 CHECK INOPERATIVE HEATED SEAT SWITCH INPUT
  • Key in OFF position.
  • Disconnect: Heated Seat Switch C320 (Driver) or C321 (Passenger) for the inoperative heated seat.
  • Key in ON position.
  • Measure the voltage between heated seat switch C320-2 (driver) or C321-2 (passenger), circuit 1064 (YE/LB), harness side and ground .
    s5r~tr~en~file=a0078820.gif~gen~ref.gif
  • Is the voltage greater than 10 volts?
Yes
GO to J6 .

No
REPAIR circuit 1064 (YE/LB). TEST system for normal operation. J6 CHECK CIRCUIT 57 (BK) FOR AN OPEN
  • Measure the resistance between heated seat switch C320-4 (driver) or C321-4 (passenger), circuit 57 (BK), harness side and ground.
    s5r~tr~en~file=a0078821.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
INSTALL a new heated seat switch. TEST the system for normal operation.

No
REPAIR circuit 57 (BK). TEST the system for normal operation It's not that simple , being a fuse . It's probably the relay or the heating element .
PINPOINT TEST K: SEAT DOES NOT HEAT BUT THE HEATED SEAT INDICATOR ILLUMINATES WHEN PRESSED ? Does it ?
Your best bet would be to take to a qualified repair shop .
Do

Jun 29, 2016 | 2004 Ford Explorer Sport Trac

1 Answer

Where are relays for heated seats in 2004 monte carlo ss


Hi jkelley, I'm glad to help!

Usually in most cases when the heated seats quit working its the heated seat element that you sit on under the padding. Here's what I want you to do: Turn the key on then push the heated seat on button and see if it lights up. This is a quick test but not always an accurate test because the switch could still be working but the LED Light could be bad. BUT, in most cases this is a good test. If it lights up then its safe to say that its mostly likely the ELEMENT that's bad. Most of the time if you'll raise the seat cover you'll see that the element is burnt. Hope this helps and have an awesome day.

Mar 15, 2013 | Cars & Trucks

1 Answer

2003 chevy avalanche heated seats wont stay on


The following diagnosis might be helpful if the vehicle exhibits the symptom s described in this PI. Condition Concern Driver and passenger heated seats inoperative or shut off in 30 seconds. There will be DTCs B2435, B2440, B3606 and or B1825 set in the Drivers Seat Module. The adjustable pedal position sensor, seat recliner position sensor and both heat seat thermistors share the same 5 volt reference internal to the Drivers Seat Module. A fault in any of these components circuits can make the heated seats inoperative or shut off in 30 seconds, as well as, the seat recliner and/or adjustment pedals may move in short increments when operated. A fault in heated seats, adjustable pedal or seat recliner will affect BOTH heated seats. Note Even if the vehicle is not equipped with adjustable pedals DTC B3606 still may set.Recommendation/Instructions To help isolate the area of concern use the Tech 2 and go to Sensor Data in the Drivers Seat Module. Monitor the following parameters for being out of range Recline Position Normal range .39V 4.58V Pedal Position if equipped Normal range .39V 4.58V Psgr. Seat Heat Sensor- Normal range 1V-4V Drvr. Seat Heat Sensor Normal range 1V 4V If a parameter is found to be out of range inspect circuits for any opens, shorts to ground, or voltage. If none found replace the suspect component Please be aware of the following common areas of concern The adjustable pedal position sensor internally shorted pulling the 5 volt reference low. Disconnect the adjustable pedal position sensor and see if the heated seats start working correctly, if so replace.Note Important The APP accelerator Pedal Position sensor is NOT the adjustable pedal position sensor. Make sure the correct sensor, adjustable pedal position sensor, is disconnected.The seat recliner position sensor internally shorted pulling the 5 volt reference low. Disconnect the recliner position sensor and see if heated seats start working correctly, if so replace.An open in either heated seat thermistor circuits signal or low reference The most common is the passenger thermistor where it passes through seat connector C305 pin L or K or C399 pins R or G A chaff to ground on either heated seat thermistor signal circuits. The most common is circuit 5475 black red or dark blue shorted to ground in the passenger seat near the buckle.Note Important The heated seat thermistors act differently to OPENS and SHORTS than the adjustable pedal position sensor and seat recliner position sensor. The adjustable pedals and seat recliner sensors can be disconnected for testing of the heated seats. Where as the heated seat thermistor circuit must be working correctly before EITHER heated seat will operate. Disconnecting one thermistor, which may have a concern will not allow the opposite heated seat to work correctly, BOTH side must be operational before EITHER heated seat will perate.Clearing DTCs If DTCs will not clear when using the Tech 2 after a repair has been made, try operating the device in which the repair was made. Example, if a repair was made to the passenger heated seat thermistor circuit, the DTCs may not clear unless the passenger heated seat is operated.Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed GM bulletins are intended for use by professional technicians, NOT a do it urselfer. They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.

The purpose of this bulletin is to provide the technician with the following service nformation Heated Seats Switch Operation Heated Seats Switch Diagnostics Heated Seats Switch Customer Information Switch Operation The engine must be running for the heated seat feature to work. The heated seats will shut off automatically when the ignition is turned off.Two buttons, located on the door, are used to control the heated seat. Press the orizontal (RH) button to heat the entire seat, back and cushion. Press the vertical (LH) button to heat ONLY the seat back.The three light bars are an indicator of the level of heat selected for either the entire seat (horizontal button) or ONLY the seat back (vertical button) To heat both the seat back and seat cushion at the same time, press the horizontal (RH) button with the heated seat symbol one time. All 3 light bars will glow indicating the HIGH temperature etting.The horizontal (RH) button does NOT have an ON FF indicator light.Press the button a second time, 2 light bars will glow indicating the MEDIUM temperature setting for the entire seat.Press the button a third time, 1 light bar will glow indicating the LOW temperature setting for the entire seat.Press the button a fourth time to turn the entire heated seat OFF.To heat ONLY the seat back, press the vertical (LH) button one time. An ON FF indicator light over the heated seat back symbol will glow to designate that ONLY the seat back is being heated.All 3 light bars over the horizontal (RH) button will glow indicating the HIGH temperature setting for ONLY the seat back.Press the button a second time, 2 light bars will glow indicating the MEDIUM temperature setting for ONLY the seat back.Press the button a third time, 1 light bar will glow indicating the LOW temperature setting for ONLY the seat back.Press the button a fourth time to turn the heated seat back OFF.Switch Diagnostics mportant: In order to eliminate unnecessary part replacement and comeback repairs, it is essential that the appropriate diagnostic tables and aids found in the applicable manuals are followed.Verify the condition prior to making any repairs. Refer to Seats and Seat Controls in the applicable Owners Manual or this bulletin for proper heated seat switch operation information.If an improperly operating front heated seat condition exists, refer to the Diagnostic Information and Procedures in the Seats sub-section of the applicable Service Manual in order to diagnose the system accurately.When measuring the resistance of the seat heater elements, ensure the values are within the updated range of 1.5-5.5 ohms. Refer to DTC B2425 or B2430-Clearing the DTC in the Diagnostic Information and Procedures in the Seats sub-section of the applicable Service Manual.Customer Information Some heated seat components from the above listed vehicles have been returned to the Warranty Parts Center (WPC) for heat function not operating properly. Analyses of these parts show 'no out of specification condition' or No Trouble Found (NTF)Provide customers with the knowledge that if bumped, either one of the heated seat switches can be activated/deactivated accidentally.Ensure customers have a thorough understanding of how the heated seat switches function.GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.

Oct 26, 2011 | 2003 Chevrolet Avalanche

1 Answer

2004 GMC Envoy driver's side heated seat quit


I have the same problem except the back of mine works but the bottom doesn't. Passenger side is fine. Let me know what you find out if you could.

Aug 26, 2011 | 2004 GMC Envoy

1 Answer

No indicators working found fuse box which fuse?


When you are talking about "indicators" we could assuming that your are refer about signal lights. This work with "flashers" devices.

For 1996 Audi A4 2.8L SFI 6cyl the Flasher is located in front seating area, driver side, under dash, behind dash lower panel, mounted above driver side of steering column.

About generic fuses, open the driver side door. Remove panel on left side of dash. Fuse box is behind panel:

Fuse # / Description / Amps
1 / Heated washer jets / 5
2 / Turn signals flasher unit / 10
3 / Headlight washer, illumination of glove compartment, engine compartment, climate control, automatic transmission, instrument cluster / 5
4 / License plate light / 5
5 / Instrument cluster, seat heating, test connection for cruise control, bulb monitor for auto-check control, Automatic transmission display, switch lighting, mirror switches and actuators, airbag warning light, outside temperature indicator, Climate control / 10
6 / Central locking system / 5
7 / Anti-lock brake system / 10
8 / Vacant
9 / Mirror heating / 10
10 / Vacant
11 / Cruise control (automatic transmission) / 5
12 / On board diagnostic system / 10
13 / Brake lights / 10
14 / Interior lights, reading lights, anti-theft alarm system, vanity mirror / 10
15 / Instrument cluster, power windows, climate control, automatic transmission / 10
16 / Anti-lock brake system, Anti-Slip-Regulation / 5
17 / Heated door locks / 10
18 / High beam right / 10
19 / High beam left / 10
20 / Low beam right / 15
21 / Low beam left / 15
22 / Tail and side marker right / 5
23 / Tail and side marker left / 5
24 / Wiper and washer system / 25
25 / Blower for heating, climate control / 30
26 / Rear window defogger, mirror heating / 30
27 / Rear window wiper / 15
28 / Fuel pump / 15
29 / Engine timing / 20
30 / Sun roof / 20
31 / Tail lights, cruise control, automatic transmission / 15
32 / Engine timing / 20
33 / Cigarette lighter / 15
34 / Engine timing / 15
35 / Trailer receptacle / 30
36 / Fog lights / 15
37 / Radio / 20
38 / Luggage compartment light, central locking system / 15
39 / Emergency flasher / 15
40 / Horn / 25
41 / Anti-lock brake system / 25
42 / Vacant
43 / Vacant
44 / Seat heating / 30

Hope this helps (remember to rate and comme this free answeer).



Jun 16, 2011 | 1996 Audi A4

1 Answer

Schematic to driver side fuse box


Cavity Fuse Description
1) 15 Amp Blue Horn Relay, Power Sunroof
Relay, Power Window Relay
2) 10 Amp Red Rear Fog Lights (Export Only)
3) 20 Amp Yellow Cigar Lighter
4) 10 Amp Red Headlight Low Beam Right
5) 10 Amp Red Headlight Low Beam Left
6) 20 Amp Yellow Body Control Module/Power Door Locks
7 )10 Amp Red Left Park Light/Left Tail Lamp/License Plate Lamp
8) Spare
9) 10 Amp Red Right Park Light/RightTail Lamp/License Plate Lamp/Cluster
10) Spare Cavity Fuse Description
11) 15 Amp Blue Flasher
12) 15 Amp Blue Stop Lights
13) 10 Amp Red Body Control Module/CMTC/Cluster/Pass. Airbag On,Off Indicator, Auto Daylight
Mirror/Light Bar Switch (Renegade Only)
14) 10 Amp Red PDC Fuel Pump/AC Clutch,
Starter Relay/Engine
Controller/Transmission
Controller (Diesel Only)
15) Spare
16) 20 Amp Yellow Power Outlet (Rear)
17) 15 Amp Blue Rear Wiper
18) 20 Amp Yellow Radio Choke & Relay
Cavity Fuse Description
19 20 Amp Yellow
Frt Fog Lights/Trailer Tow
Stop and Turn Lights
20 Spare
21 10 Amp Red Radio
22 20 Amp Yellow
Power Sunroof Relay/
Antenna Module (Export
Only)
23 Spare
24 10 Amp Red PDC Blower Motor
25 10 Amp Red Heated Seat Switches/HVAC
Control Head/Trailer Tow
Battery Charge
26 10 Amp Red Headlight High Beam Right
27 10 Amp Red Headlight High Beam Left
28 Spare
29 10 Amp Red Heated Mirrors/Rear Window
Defroster Indicator
Cavity Fuse Description
30 15 Amp Blue Heated Seat Module
31 Spare
32 10 Amp Red Wiper Switch/Front and
Rear Wipers
33 10 Amp Red SKIM Module/Data Link
Connector
34 15 Amp Blue Body Control Module/
Cluster/Interior Lights,
Hands Free Module/Radio/
CMTC/ITM Module & Siren
(Export Only)
35 Spare
36 10 Amp Red Airbag Control Module/
Occupation Classification
Module (Right Front Seat)
37 10 Amp Red Airbag Control Module
38 10 Amp Red ABS Controller/Shifter Assembly
39 10 Amp Red Hazard Flasher (Turn
Signals)/Backup Lamp
Switch (Manual Transmission
Only)/Transmission Range
Switch (Automatic Transmis

May 23, 2011 | 2005 Jeep Liberty

1 Answer

The driver's side heated seat won't turn off on my 2003 Mecury Moutaineer. Also, how do I change my cabin filter?


Your vhicle build date is on a blue sticker on the driver door or door frame. If not there, check other doors.
The heated seat Module is under the seat. You can unplug the connector on it or the heated seat switch to shut it off. I supect the module is bad. get one used from car-parts.com. The cabin air filter is under the leaf screen at the base of the windshield. Remove wiper arms and leaf screen for access. Please rate, thanks. Principles of Operation - Heated Seats - Vehicles Built 03/2002 Onward
NOTE: Two heated seat modules are used, one for vehicles built up to 03/2002 and one for vehicles built 03/2002 onward. The modules are not interchangeable.
The driver and passenger heated seats share a common battery and ignition feed. A shared ground source supplies the heated seat control switches. When the heated seat control switch is pressed with the ignition switch in RUN or START, a momentary ground signal is sent to the heated seat module. The heated seat module then supplies power to the heating element circuit. The cushion element and seat backrest element are wired in series and powered by the same output. The heated seat module also will ground the separate indicator circuit at the dual automatic temperature control (DATC) module display panel to indicate an ON state. The heated seat module will remain on until the heated seat control switch is pressed and a momentary voltage signal is received, or until 10 minutes expire. If the ignition source is removed from the module, the heated seat module will enter an OFF state and will not return to ON until the switch is once again pressed with the ignition switch in RUN. The heated seat module is designed to heat the seat to 37.5?C (99.5?F) and maintain the temperature until time-out or switched off. This temperature is maintained by the heated seat module monitoring the temperature sensor located in the seat cushion element, and adjusting the current flow to the heating elements.
--------------------------------------------------------------------------------------------------------------------------------

May 22, 2011 | 2003 Mercury Mountaineer

2 Answers

I have a 1993 VW Passat VR6, My problem is when I try to start it, I have no spark from the spark plugs..What could be the problem or how do I fix this?????


GO TO THIS SiTE TO CHECK THE FUSE BOX!
http://vwtech.no-ip.info/images/golf/post90.gif

This are the FUSE and RELAY number SLOT!
Fuse No. Description Ampere Rating 1 Headlight, low beam, left 10 2 Headlight, low beam, right 10 3 Instrument panel lights, license plate lights 10 4 Glove compartment light 15 5 Wiper/washer 15 6 Fresh air blower 16-valve only: Air conditioning 20 7 Taillights, side marker light, right 10 8 Taillights, side marker light, left 0 9 Rear window defogger 20 10 2.0 16-valve only: Fog lights 15 11 Headlight, high beam, left,High beam indicator light 10 12 Headlight, high beam, right 10 13 Horn 16-valve only: Radiator cooling fan 10 14 Back-up lights, washer nozzle heaters 10 15 2.0 16-valve only: Engine electronics, stabilizer valve, cold start valve 10 16 Instrument panel warning lights, 16-valve only: Multi function indicator 15 17 Emergency flasher switch, turn signals 10 18 Fuel pump, oxygen sensor heater 20 19 Radiator cooling fan, air conditioning 30 20 Brake lights, cruise control 10 21 Interior lights, digital clock 16-valve only: Luggage compartment light,multi function indicator, central locking 15 22 Radio, cigarette lighter 10
Relays Relay No. Description 1 Air conditioning 2 Open 3 Digifant control unit 4 Load reduction relay 5 Low coolant level control unit or Open 6 Emergency flashers 7 Rear Wiper 8 Intermittent wipers 9 Seat belt warning system control unit (possibly headlight warning too?) 10 Fog lights 11 Horn 12 Fuel pump (except diesel)Glow plugs (diesel) 13 Radiator cooling fan after run (except 16-valve)2.0 16-valve: Starter interlock relay 14 Automatic trans., coolant temperature indicator,starter interlock relay (except 2.0 16-valve)2.0 16-valve: Radiator cooling fan after run 15 ABS pump relay 16 ABS relay 17 Heated seat control unit, driver 18 Heated seat control unit, passenger, or power seat circuit breaker 19 Automatic transmission 20 Open 21 Power window relay, ABS hydraulic pump fuse 22 ABS valves fuse 23 Air conditioning, power seat fuse 24 Power window fuse

Nov 17, 2010 | 1993 Volkswagen Passat

1 Answer

Driver heat seat not working


check under seat fof broken or unplugged wires

Oct 23, 2008 | 2005 Buick Rendezvous

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...