Question about BMW 750

Open Question

Need to program garage door opener in BMW 1998 740il

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 78 Answers

SOURCE: 1998 bmw 740il will not start even with new a battery

If you checked all the fuses try putting the car in neutral sometimes the shifter gets misadjusted and wont start till the car is completely in park.If not check for a lose wire to the starter.If the car has an after market alarm you will have to turn it off before starting there should be a little buuton under the drivers dash or kick panel.GOOD LUCK

Posted on May 01, 2009

  • 4 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

You can download the operators manual for free at chrysler.com. It has the instructions to program the garage door opener. It's fairly easy with the instructions.

Good Luck,
Ray

Posted on May 11, 2009

  • 1348 Answers

SOURCE: programming garage door opener

there are three buttons on the opener.hold the 2 outside ones down for 25 to 30 seconds to erase the program. once the light (if equipped)flash rate changes,let go.
then push any one of the the three buttons and hold it in. and then push your remote. when the flash rate changes,the code is now in the homelink transmitter.the slt and slt plus had that feature.

Posted on May 14, 2009

crapiemael
  • 241 Answers

SOURCE: need to program/link garage door opener with the one on the visor in the car

Depending on the name brand of the garage door opener, there is a button on it you press and you have about 30 seconds to set the button in the car to the signal. Read you car manual on how to set the visor opener, probably press and hold the button in after pressing the button on the garage door opener motor. Get someone to help you in the garage on a ladder. Mine is a Sears and this is how it works.

Posted on May 29, 2009

  • 1 Answer

SOURCE: programming the garage door opener

Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguars owners manual. Though the procedure described in the owners manual was straight-forward and understandable, I was unsuccessful in getting the vehicles remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the Rolling Code feature.

To begin with, be sure to clear previous codes on your Jaguars garage door opener by first turning (rotating) the ignition key to the I position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle buttons red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguars garage door opener console buttons. Choose which button on your Jaguars remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguars opener button. The red light on your Jaguars center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the Learn function on your Genie garage door opener. Press the Learn button on your Genie garage door opener. The red LED adjacent to the Learn button will begin to flash. You now have 30 seconds in which to program your Jaguars opener button. Using the same button you just used in the part 1 procedure, press and hold the same button for several seconds. As before, your Jaguars red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center buttons red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguars remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguars remote button confirms to the Genies rolling code that your Jaguars signal is legitimate and is to be trusted from then on.

Posted on Dec 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Attempting to set my 2002 suburban garage door opener with my remote opener how is this done


First you need to program the car with garage door remote, then program the garage door unit to the car. Hold Down garage door remote button and button of your choice in the car, the small light on the car will blink when it has learned it's code. Then press program button on garage door unit , within 15 seconds press and hold the button in the car that you programmed , when the the light starts to blink again, it should work.

Jan 14, 2011 | 2002 Chevrolet Suburban

Tip

2010 BMW 528XI Garage Door Opener Homelink Setup


**** >>> This setup I performed with my new 2010 BMW 528XI Garage Door Homelink and Chamberlain Garage Door Opener <<< ****

Chamberlain:
01. Power off or unplug the garage door opener motor power supply (which is mounted on ceiling of the garage) ;;;

02. keep the garage door opener transmitter in your hand (do not press any button at this time) ;;;

03. In your 2010 BMW 528XI Homelink button (which resides under rear view mirror) press the 1st and 3rd homelink button together for about 30-40 seconds (i.e., until the yellow light blinks fast) and when the yellow light next to the homelink button blinks fast release from pressing the (homelink) buttons ;;;

04. now hold the garage door opener transmitter closer (means within 2-4 inches) to the homelink button (either 1st or 2nd or 3rd) whichever you are planning to program to open the garage door ;;;

05. now press the garage door opener transmitter button and chosen homelink button (either 1st or 2nd or 3rd whatever you need) together ;;;

06. the yellow light (next to homelink button) initially may blink slowly but after few seconds (may be 10-20 seconds) will blink fast; once it started blinking fast release from pressing both garage door opener transmitter and homelink button ;;;

07. Now plug or power on the main garage door opener motor (which is mounted on garage ceiling) ;;;

08. On the main garage door opener motor (which is mounted on garage ceiling) press the "LEARN" button (once you press it may have yellow/orange color light; make sure the light is on) ; then within 30 seconds do the next steps #9, #10, #11 very carefully ;;;

09. go to your car and press the homelink button you programmed and hold it for 4 seconds and then release it --> 1st iteration ;;;

10. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 2nd iteration ;;;

11. again hold the same homelink button you programmed and hold it for 4 seconds and then release it --> 3rd iteration ** important note; generally three iterations are not necessary; and steps #9, #10, #11 must be performed within 30 seconds ** ;;;

12. during one of the iteration you will hear "CLICK" sound one-time from Garage door motor (which is mounted on ceiling) and if you have light attached with it; it will blink once (** if you hear the CLICK sound and/or light blinks once**) then the particular homelink button is programmed ;;;

13. now press the programmed homelink button; the garage door will open or close (but always it will take 3 or 4 blinks in yellow light or 2-3 seconds before the garage door opens or closes and which is normal) ;;;

** Thats it, your 2010 BMW 528XI Garage Door Opener Homelink setup is complete ** ;;;

You can program rest of the homelink button the same way but following from the steps between #4 and #13 ;;;

Hope this steps will help you to program chamberlain Garage door opener in 2010 BMW 528XI Homelink. ;;;


** possibly the above same steps may work with other BMW 5-series cars homelink too (but I'm not sure) **

on May 29, 2010 | BMW 528 Cars & Trucks

1 Answer

I don't have the owner's manual for my 2002 GMC Yukon XL Denali. Do you know how to program the garage door opener?


I hope this helps.

Programming the HomeLink Transmitter
Do not use the HomeLink Transmitter with any garage
door opener that does not have the stop and reverse
feature. This includes any garage door opener model
manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
It is recommended that a new battery be installed in
your hand-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Decide which one of the three channels (one of the
HomeLink buttons) you want to program.
2. Press and hold the desired button on HomeLink
through Step 3.
3. When the HomeLink indicator light begins to blink
slowly (this may take up to 30 seconds), hold the
hand-held transmitter about 1 to 3 inches (3 to 8 cm)
away from HomeLink and then press and hold the
transmit button on the hand-held transmitter.
Continue to hold both buttons until the indicator
light on HomeLink begins to flash rapidly (this may
take up to 90 seconds).
If you have trouble programming HomeLink, make
sure that you have followed the directions exactly as
described and that the battery in the hand-held
transmitter is not weak. If you still cannot program it,
move the hand-held transmitter to the left or right or
forward or backward or flip it upside down. HomeLink
may not work with older garage door openers that do
not meet current Federal Consumer Safety Standards.
If you cannot program the transmitter after repeated
attempts, refer to "Training a Garage Door Opener with
Rolling Codes" later in this section or contact the
manufacturer of HomeLink at 1-800-355-3515,
or on the internet at www.homelink.com.
Be sure to keep the original hand-held transmitter in
case you need to erase and reprogram HomeLink.


Training a Garage Door Opener with a
"Rolling Code" Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see "Programming the
HomeLink Transmitter" listed previously. If you have
completed this programming already, you now need to
train the garage door opener motor head unit to
recognize HomeLink.
1. Find the "Learn" or "Smartbutton" on the garage
door opener motor head unit. The exact location and
color will vary by garage door opener brand. If you
have difficulty finding the Learn or Smart button,
refer to your garage door opener owner's manual or
contact the manufacturer of HomeLink at
1-800-355-3515, or on the internet at
www.homelink.com.
Because of the steps involved, it may be helpful
to have another person assist in programming
the transmitter.
2. Press the Learn or Smart button on the garage
door opener motor head unit. An indicator light will
begin to flash when the motor head unit enters the
training mode.
Following this step, you have 30 seconds to
start Step 3.
3. Return to HomeLink in your vehicle and firmly
press and release the programmed HomeLink button
three times.
The rolling-code garage door opener should now
recognize HomeLink. You may either use HomeLink
or the hand-held transmitter to open the garage door.
If after following these instructions, you still have
problems training the garage door opener, contact the
manufacturer of HomeLink at 1-800-355-3515,
or on the internet at www.homelink.com.
www.gmcextendedwarranty.com

Dec 19, 2010 | GMC Yukon XL Cars & Trucks

2 Answers

How to program my cars garage door opener buttons for my garage door.


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.

HOPE THIS HELPS

May 15, 2010 | 2001 Nissan Altima

1 Answer

Need to program/link garage door opener with the one on the visor in the car


Depending on the name brand of the garage door opener, there is a button on it you press and you have about 30 seconds to set the button in the car to the signal. Read you car manual on how to set the visor opener, probably press and hold the button in after pressing the button on the garage door opener motor. Get someone to help you in the garage on a ladder. Mine is a Sears and this is how it works.

May 29, 2009 | 2006 Audi A4

2 Answers

Program instruction garage door opener in 2005 chrysler pacifica


if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Apr 24, 2009 | 2005 Chrysler Pacifica

1 Answer

Program garage door opener in 2005 rx 330


There are 3 programmable Homelink buttons you can use for different remotes. Just to the right of the buttons there is an indicator light.

Decide which button you want to program. Point the none battery end of your remote 1"-3" away from the Homelink panel and press both the remote and desired Homelink button down and hold them down at the same time. After about 20 seconds, the Homelink indicator light will change from a slow flashing to a rapid flashing. You can then release both buttons,
If the garage door responds to the Homelink, your done! If not, your garage door uses a rolling codes transmitter and must be trained.
Find the training button on your garage door opener's transmitter (usually mounted on the ceiling). Press the training button and within 30 seconds press and release the programmed Homelink button twice. If the garage door opener operates, you're done! If not, press and release the Homelink button a third time and the garage door should respond. If it still does not, you may have a very old garage door opener with a none digital transmitter (like I did). In that case, you either need to buy a new opener or try to replace the transmitter with a modern digital unit (as I did). Advantage: cheaper than a whole new garage door opener.
Disadvantage: The newer openers incorporate safety features that my old opener does not have.

Apr 16, 2009 | 2005 Lexus RX330

1 Answer

How do u program garage door opener for chevy impala 2003


YOU WILL NEED TO REPROGAM "ALL" YOUR REMOTES AND CONTROLS AGAIN USING THE GARAGE DOOR OPENER BUTTONS ON THE GARAGE MOTOR .....

HAVE ALL YOUR REMOTEA YOU NEED TO PROGRAM IN HAND FOR QUICK OROGRAMMING.....

Dec 30, 2008 | 2002 Chevrolet Impala

2 Answers

How to program my garage door opener


THE CODE IN THE REMOTE HAS TO BE SET YO THE SAMR AS THE RECIVER ON THE GARAGE DOOR! LOOK WHERE BATT GOES

Dec 07, 2008 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...