Question about 1995 Chevrolet Camaro

1 Answer

I need to change the fuel pump on a1995 chevy camaro z28

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

The fuel pump is part of the fuel sender assembly located inside the fuel tank.

  1. Release the fuel system pressure and disconnect the negative battery cable.
  2. Drain the fuel tank, then raise and safely support the vehicle.
  3. Remove the fuel tank from the vehicle.
  4. Clean the area surrounding the sender assembly to prevent contamination of the fuel system.
  5. To remove the fuel sender from the tank, remove the fuel sender assembly nuts and retaining ring. Carefully remove the sending unit from the fuel tank. Discard the O-rings.
  6. If necessary, separate the fuel pump from the sending unit assembly.
To install:
  1. If removed, install the fuel pump to the sending unit. If the strainer was removed, it must be replaced with a new one.
  2. Inspect and clean the O-ring mating surfaces.
  3. Install a new O-ring in the groove around the tank opening. If applicable, install a new O-ring on the fuel sender feed tube.
  4. Install the fuel sender assembly as follows:
    1. The fuel pump strainer must be in a horizontal position, and when installed, must not block the travel of the float arm. Gently fold the strainer over itself and slowly position the sending assembly in the tank so the strainer is not damaged or trapped by the sump walls.

  5. Install the retaining ring and nuts, then tighten the nuts to 63 inch lbs. (7 Nm).
  6. Install the fuel tank assembly.
  7. Lower the vehicle.
  8. Fill the fuel tank, tighten the fuel filler cap and connect the negative battery cable.
  9. Turn the ignition switch to the ON position for 2 seconds, OFF for 10 seconds, then back to the ON position. Check for fuel leaks.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I wanna know where is the electric fuel pump relay on my chevy camaro z28 1991. the engine run good when he is clod but stop when he is hot i think is the relay


Sounds like a crank sensor rather than fuel pump. You should check your fuel pressure at the injector rail to get a better idea of the cause.....Mike

Jun 19, 2011 | 1991 Chevrolet Camaro

2 Answers

'94 chevy camaro z28 losing power while driving,


check the mas air flow meter could be starting to go and not yet throwing a code.

Jan 17, 2010 | 1994 Chevrolet Camaro

1 Answer

2 fuel pumps on 84 z28????!!!?


My guess is if you changed to an older style sending unit, you could eliminate that electric pump & just use your mechanical one as they did before EFI.

Apr 16, 2009 | 1984 Chevrolet Camaro

1 Answer

1984 camaro z28 gas gauge


float arm in the tank is either stuck or broken. its connected to the fuel pump assembly

Mar 25, 2009 | 1984 Chevrolet Camaro

1 Answer

No power to fuel pump.


Don't forget to check for a good ground at the pump, I've seen this problem pay for a new fuel pump more than once.

Mar 11, 2009 | 1985 Chevrolet Camaro

1 Answer

Lack of Fuel


Just because the fuel pump is on does not mean it is delivering the proper pressure. Some systems need as much as 35 psi to function properly. I would look there. I am assuming that you have checked the pressure as you had mentioned that the "Injectors have a lack of pressure" in your statement. Some of the old chevys used to use a "Sock" type filter on the pick up tube in the fuel tank. A possibility? Could be partially clogged. Good Luck

Feb 16, 2009 | 1990 Chevrolet Camaro

2 Answers

My 94 z28 camaro chuggs when i punch it


sounds like a fuel pump struggling to pass its contents. try running a treatment solution in your tank. if this fails to work, you will need a new fuel pump to correct this problem. sometimes, trash will build up in your tank and it will cause build up in the jets. you should check vacuum as well if needed.

Jan 28, 2009 | 1994 Chevrolet Camaro

1 Answer

Locating the Fuel filter


the fuel filter is located under the car in fuel line just before the fuel tank

Oct 04, 2008 | 1983 Chevrolet Camaro

1 Answer

Fuel pump


A fuel pressure gauge is the most accurate way. You can turn the key on and listen for a humming sound, that tells you the pump is running, but dosn't mean it's completely functional.

Sep 13, 2008 | 1996 Chevrolet Camaro

Not finding what you are looking for?
1995 Chevrolet Camaro Logo

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...