Question about 2001 Subaru Outback
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
heavier oil if you are not in a cold climate. but before you do that have the oil pressure checked. We used to use a can of STP every once in a while on a motor in a dodge we had... nothing wrong with it... was just noisy.
Posted on Feb 05, 2009
Posted on Aug 09, 2009
If the light was flashing when it came on, then it means your engine is misfiring.
A solid light can mean anything from a loose/faulty gas cap to a transmission issue.
This light comes on when the computer detects a fault of some sort in its diagnostic tests. If it keeps detecting this issue, the light will remain on. If the light turns off, then it has detected that the issue may no longer be present.
In order to find out what the exact reason was for your light, You need to have your car computer scanned to retrieve the code that the computer would have stored when the light triggered. Most garages will do this free of charge. The code will tell you what may have caused the light to initially turn on.
Posted on Oct 22, 2009
Testimonial: "thanka "
In 2005 Subaru moved the fuel filters to the fuel tank for both 4-cyl and 6-cyl cars. What is confusing is the statement in the owner's manual about replacement intervals; the statement actually only applies to 4-cyl cars. Even though the filter is mounted in the tank, this is still a replaceable element on 4-cyl, but not on 6-cyl. The 6-cyl filter element is part of the entire fuel pump assembly (a $300 assembly) and is not sold separately. Therefore the 6-cyl filter is intended to be a "lifetime" part, which really means it gets replaced when the fuel pump fails and the entire pump assembly is replaced.
Posted on Oct 30, 2009
Testimonial: "Excellent and timely advice. He cleared up a confusing question I had and got conflicting information from the vehicle owner's manual."
This is not your average timing belt replacement due to being a double overhead cam that is also an interferance fit.First remove cooling fans.2-Loosen drive belts and remove.3-Remove crank pully.4-Remove timing covers.You will see 4 cam sprockets.Theses sprockets contain single and double referance marks.You will be using the double referance marks.Rotate engine until the double referance marks are facing each other.This is to be done the same way that the American autos timing Chain systems are done but you will have 2 small double lines to line up not dots.The next step is the most important step and is of utmost imortance.THE CAMSHAFT HAVE TO BE LOCKED IN PLACE--FAILURE TO DO SO CAN RESULT IN BENT VALVES.The cam sprocket holders can be bought or rented.You can make your own as well by making 2 wedges with bolt through the middle.Slip in between sprockets and tighten enough to hold sprockets.Do not use excessive torque while tightening wedges sprockets are not made of steel but rather a composite material.Next you will have to remove the tenioner.The tensioner has to be retracted and pin istalled to hold in retracted position.The tension device has to be retracted with care or will be damaged.You can not exceed 50 pounds pressure on the plunger.The simplest method is to reract while still in vehicle, it takes 15 minutes to properly retract the plunger.By pulling up on the tensioner by hand with about 18 pounds of force --50 will be exerted at the plunger.When fully retracted insert pin to hold in reracted position.Next check to make sure that cam wedges are holding and no sprocket are trying to move,when satisfied remove one of the rollers at the bottom on the side where you left hand would be standing in front.Pull off belt.Replacement belt will have referance marksone line will go to crank sprocket face up others will line up with other sprocket marks.Reinstall roller followed by tensioner then pull pin you have holding tenioner retracted.Remove wedges.Reinstall covers fans belts.Do not be intimitaded by this replacement.Everything is very easy to get to.Be sure cams are locked and that damage is not done to tensioner and it is straight forward.
Posted on Nov 06, 2009
Tips for a great answer:
Nov 13, 2015 | Subaru Cars & Trucks
Apr 14, 2012 | 2001 Subaru Outback
Nov 19, 2010 | 2001 Subaru Outback
Nov 16, 2010 | 2000 Subaru Outback
Feb 17, 2010 | 2001 Subaru Outback
Feb 09, 2010 | 2001 Subaru Outback
Dec 30, 2009 | 2001 Subaru Outback
Feb 19, 2009 | 2001 Subaru Outback
Jul 06, 2014 | 2001 Subaru Outback
475 people viewed this question
Usually answered in minutes!