Question about 2004 Jeep Grand Cherokee

1 Answer

How do i replace my front turn signal bulb - 2004 Jeep Grand Cherokee

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Open hood. you will see 7mm bolt. take out now should be able to pull the hole light assembly out. pull hard. there should be 5 or 6 bulbs. if you're looking down with the wires still attached to the assembly then they will be toward the base of the assembly(should be 2 of them)

Posted on Sep 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My left turn signal was flashing fast. I checked bulb in back left. Turn signal good but bulb below it was out. I changed that one but turn signal still flashing fast. all other bulbs look good. ??


If the front and rear bulbs flash fast also, replace the hazard switch or you could live with it. As they are working. If one doesn't work, check grounds. I just run a new ground, much easier than cutting open the harness to find the break.

May 31, 2015 | 2012 Nissan Rogue

2 Answers

My right front turn signal on my 2001 ford ranger doesnt work and my inside right turn signal light on dash doesnt work and flashes really fast. Buld on right side was replaced and works when lights


was the correct bulb used? this sounds like a single function bulb was used NOT the bulb that will light with the headlights and ALso produce turn singles

Dec 06, 2014 | 2001 Ford Ranger Regular Cab

3 Answers

Fast flashing turn signals


I would change out the turn signal bulb on the right front. A blown bulb can cause the fast flash issue. The signals staying on is not related to the bulb being blown. That is most likely a problem with the multifunction switch, the knob you use to signal.

Jul 12, 2013 | Buick Cars & Trucks

1 Answer

Grand prix front turn signals lights will not work but rears flash rapidly.


Definitely not the flasher, as long as it is flashing or blinking somewhere. Rapid flashing indicates a burned bulb, but since you already tried new bulbs in front, possibly bad bulb sockets, loose connectors, or a bad ground for the front bulbs. If you have a test light or voltmeter (multimeter), check for power at the socket when turns are on. If power then at the front, try new bulbs or trace the ground for those lights. If no power to the socket for turn signals, recheck wiring.

Apr 02, 2013 | 1995 Pontiac Grand Prix

1 Answer

How do you change a front signal bulb on a 2004 accord


Front turn signal bulb replacement

1. Remove the inner fender
2. Disconnect the 3p connector from the front turn signal/side marker light.
3. Turn the bub socket ( 45 degree ), counterclockwise to remove the bulb.
4. Install a new bulb in the reverse order of removal.

Apr 12, 2010 | 2004 Honda Accord

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

2 Answers

Need replace turn signal bulb


YOU HAVE TO THE FRONT HEADLIGHT HOUSING TO REPLACE THE TURN SIGNAL BULB.

Aug 24, 2009 | 1996 Chevrolet Cavalier

1 Answer

The turn signals do not work on 2000 nissan exterra.Fuse was blown. Replaced and blew again after a few seconds.


1.Remove front & Rear turn signal Bulbs.
2.Replace Fuse.
3.Signal on.
4.Fix rear Signal Bulb.
5.Fix Front Signal Bulb.
7.If your Fuse blown.
8.Defect is There.

Jun 11, 2009 | 2000 Nissan Xterra

1 Answer

2000 Accord turn signal problem


either the front or the rear turn signal bulb is blown, that is why the flash frequency is high. replace the bulb and the problem will be solved. best to replace both the front and rear turn signal bulbs. good luck.

Aug 29, 2008 | 2000 Honda Accord

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

513 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...