Question about 1997 Plymouth Voyager

1 Answer

Fuel pump imformation locxation - 1997 Plymouth Voyager

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 8,557 Answers

Fuel pump is inside fuel tank. Tank must be lowered to access pump.

Posted on Sep 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2008 GMC sierra 5.3 L with a new fuel pump. And no power to the pump. Any ideas where to look?


Fuel Pump Flow Control Module (FPCM) - LMF
The fuel pump flow control module (FPCM) is a serviceable GMLAN module. The FPCM receives the desired fuel pressure message from the engine control module (ECM) and controls the fuel pump located within the fuel tank to achieve the desired fuel pressure. The FPCM sends a 25 KHZ PWM signal to the fuel pump, and pump speed is changed by varying the duty cycle of this signal. Maximum current supplied to the fuel pump is 15 amps. A liquid fuel pressure sensor provides fuel pressure feedback to the FPCM.
Electronic Returnless Fuel System (ERFS) - LMF
The electronic returnless fuel system is a microprocessor controlled fuel delivery system which transports fuel from the tank to the fuel rails. It functions as an electronic replacement for a traditional, mechanical fuel pressure regulator. A pressure vent valve within the fuel tank provides an added measure of fuel pump flow control module (FPCM). Desired fuel pressure is commanded by the engine control module (ECM), and transmitted to the FPCM via a GMLAN serial data message. A liquid fuel pressure sensor provides the feedback the FPCM requires for Closed Loop fuel pressure control.

Fuel Pump Flow Control Module (Gas except LU3/LMG/LY6/LC9)
Mounted to the rear frame, near the spare tire mount
Wheels/Vehicle Underbody Component Views
Component Connector End Views
Fuel Pump Relay - Secondary (Gas with LY6)
On the fuse block - underhood bracket

DTC P0191: Fuel Rail Pressure (FRP) Sensor Performance
DTC P0192: Fuel Rail Pressure (FRP) Sensor Circuit Low Voltage
DTC P0193: Fuel Rail Pressure (FRP) Sensor Circuit High Voltage
DTC P0230: Fuel Pump Relay Control Circuit
The engine control module (ECM) sends the fuel enable signal to the fuel pump control module (FPCM). The control module monitors the voltage on the fuel pump relay control circuit. If the control module detects an incorrect voltage on the fuel pump relay control circuit, a fuel pump relay control DTC sets.
The control module monitors the voltage on the fuel pump relay control circuit. If the control module detects an incorrect voltage on the fuel pump relay control circuit, a fuel pump relay control DTC sets.
DTC P0231: Fuel Pump Control Circuit Low Voltage
DTC P0232: Fuel Pump Control Circuit High Voltage
DTC P023F: Fuel Pump Control Circuit
DTC P025A: Fuel Pump Control Module Enable Circuit

Your best bet , take it to a qualified repair shop , dealer .

Mar 25, 2017 | GMC Cars & Trucks

2 Answers

No fuel coming to carburator


It could be fuel pump or fuel pump relay.Click here to see how to remove fuel pump.Click here to see fuel pump.See how much the fuel pump is,make sure it's that.Here's the fuel pump relay.Here's how to remove fuel pressure.

Dec 23, 2012 | 2003 Saturn VUE

1 Answer

Turning on ignition won't start,no imformation lights come on


check your battery cables for tightness and electrolyte buildup.

Nov 30, 2012 | 2004 Chevrolet Colorado

1 Answer

The starter cranks but the engine won't start,i have change gas pump,fuses and time belt...


boy do i need a lot of more imformation on this one , first do you have spark / is fuel getting to the cylinder /is there the right fuel pressure

Jan 07, 2011 | Ford Mustang Cars & Trucks

1 Answer

What is code 1614 and how do i fix it??


code 1614 means Manufacturer Auxiliary Inputs and Auxiliary Outputs, is also a generic code for a problem with the Evaporator Solenoid Control Circuit . This means that you may have two main problem or more. Your Solenoid Control Circuit or Misfire problem. Check your misfire first. Because misfire can destroy the catalytic converter. Most of the time when you have a misfire under a load condition, such as traveling 35mph+ while adding more throttle, your ignition system is usually the cause. Probably your plug wires are worn out or you may have a leak that will cuase your ignition problem. Here are the basic common questions Ideas. First you need to analyze the situation. If the engine won't crank, you are probably dealing with a starter or battery problem. Has the starter been acting up? (unusual noises, slow cranking, etc.). Is this the first time the engine has failed to crank or start, or has it happened before? Have the starter, battery or battery cables been replaced recently? Might be a defective part. Has the battery been running down? Might be a charging problem. Have there been any other electrical problems? The answers to these questions should shed some light on what might be causing the problem. If an engine cranks but refuses to start, it lacks ignition, fuel or compression. Was it running fine but quit suddenly? The most likely causes here would be a failed fuel pump, ignition module or broken overhead cam timing belt. hope this will help you good luck. if you need more imformation you can email me at reginestacio@yahoo.com . P.S. also check your fuses or sensors this might also cuase the problem.

Glad to help,
Reginskie..


Sep 22, 2010 | 2002 Kia Sportage

1 Answer

How to change the fuel pump on a 1996 Pontiac Transport


For 1996 Pontiac Truck Trans Sport 3.4L SFI 6cyl check this procedure for Fuel Pump... there are two different electric fuel pumps used:
- A medium pressure twin turbine pump for vehicles equipped with Throttle Body Injection (TBI). - A high pressure roller vane pump for vehicles equipped with Sequential Fuel Injection (SFI).
(see Figure 1)


d7f6f20.jpg


Fig. 1: View of the fuel pump assembly and related components
The fuel pump is mounted to the fuel sender assembly inside the fuel tank. The fuel is pumped to the engine at a specified flow and pressure by the fuel pump. Excess fuel is returned to the fuel tank by the return pipe. The fuel pump delivers a constant flow of fuel to the engine even during low fuel conditions and aggressive vehicle maneuvers.

CAUTION When working on or near the fuel tank, be sure to observe the information molded on the bottom of the tank.
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure.
(see Figure 2)


42fbc79.jpg

Fig. 2: Exploded view of the fuel pump-to-tank mounting components
  1. Drain and remove the fuel tank.
  2. Remove the fuel sender assembly.
  3. Disassemble the fuel pump strainer and the fuel pump: Note the position of the strainer in relation to the pump.
(see Figure 3)


c8d9af6.jpg


Fig. 3: Remove the fuel tank locking ring with a non-sparking (brass) punch.
  1. Support the fuel pump in one hand, and grab the strainer in the other hand.
    1. Rotate strainer in one direction and pull off pump. Discard strainer.
(see Figure 4)


3c2e4a1.jpg


Fig. 4: Exploded view of the fuel pump components
    1. Remove deflector.
  1. Disconnect the fuel pump electrical connector.
  2. Loosen the two connecting clamps, if equipped.
  3. Place the fuel sender assembly upside down on the work bench.
    1. Pull the fuel pump downward to remove it from the mounting bracket, then tilt the pump outward and remove it from the connecting hose or the fuel pulse dampener.
  4. It is recommended to replace the hose and clamps, if equipped.
CAUTION Do not run the pump unless submerged in fuel
To install:
  1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body, where equipped.
  2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.

Hope this help (remember rated this).

Jun 04, 2010 | 1996 Pontiac Trans Sport

1 Answer

Knock engine sensor light on truck is hesitating/


Did they replace the knock sensor?Check the wire going to the sensor(knock).Look for a bare place hiting up against something ,grounding it out.Make sure the plug to knock sensor is good.And make sure it is making a good connection,Knock sensors also ground a part of the computer to feed back imformation.This connection is a must,the truck will not perform at all,stumble,miss,and carry on.Sometimes even backfire.If they did not replace the knock sensor,replace it with high quality sensor from NAPA,or oem from dealer.This sensor has to be made perfect,no room for inperfection.The knock sensor is easy to replace,they just screw in a hole in the block.When removing the sensors,nothing will come out such as oil or water,this is a dry threaded hole.It is a bell shaped sensor.If you don`t know which sensor is bad,purchase one.replace one,and if there is no change,replace the other side with the old sensor you just took out,it will be a good one.I hope this helps you,Let us know if it does.

Oct 05, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Volvo engine imformation d5252t


It's an engine from Audi , type AEL , very used in Europe .

Jul 28, 2009 | 1996 Volvo 850

1 Answer

Spark plug locxation?


does not have a drain plug. plugs are probably in the center of valve cover under coil packs

Oct 01, 2008 | 2006 Kia Spectra

Not finding what you are looking for?
1997 Plymouth Voyager Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...