Question about 2006 Pontiac Grand Prix

Open Question

How do you remove the power steering pulley to remove the water pump on a 2006 pontiac grand prix

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 33 Answers

SOURCE: need to change water pump

there should be holes in the pulley that you can reach with extension and socket

Posted on Dec 08, 2008

jturcotte
  • 7731 Answers

SOURCE: I'am replacing water pump 2006

you can take the power steering pump off without removing the fluid lines. Just remove the mounting bolts and push the pump aside (but don't let it tip and spill). I'm assuming you have the 3.8L engine. Instructions are pasted below.


3.8L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine coolant.
  3. Remove or disconnect the following:

    Negative battery cable. Drive belt Water pump pulley Power steering pump and move it aside Water pump

To install:
  1. Install or connect the following:

    Water pump using a new gasket and torque the long bolts to 25 ft. lbs. (34 Nm) and the short bolts to 16 ft. lbs. (22 Nm) Water pump pulley and torque the bolts to 115 inch lbs. (13 Nm) Power steering pump and torque the bolts to 25 ft. lbs. (34 Nm) Drive belt Negative battery cable
  2. Fill the cooling system.
  3. Start the vehicle and check for leaks, repair if necessary.

Posted on Sep 26, 2010

Lbogie68
  • 158 Answers

SOURCE: i need to find out

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg
*This originally came from abauto

Posted on Mar 24, 2011

cool78259
  • 228 Answers

SOURCE: trying to change my water

I normally don't pass the buck, but go to e-how.com and depending on whether your

car is supercharged or not they tell you step by step how to remove your belts ,and

where the tensioner is located. there isn't enough space on this page to give you directions.

good luck!

Posted on Jul 14, 2011

  • 452 Answers

SOURCE: how to remove water pump

in some case you half to remove the power steering pully to complete this

Posted on Aug 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a '06 Pontaic Gran Prix - I cannot get the bottom right bolt out to remove water pump. How do i move idler pulley?


To get that last bolt out you need to move the power steering pump out of the way. Just remove the two bolts holding the PS pump and push it aside. You don't have to remove the pump hoses you just need to move it an inch towards the firewall.

Apr 09, 2014 | 2006 Pontiac Grand Prix

1 Answer

How do i remove power steering pulley to take out water pump


You don't need to remove the pulley. There are 2 bolts that hold the PS steering pump on the block. Remove them and move the pump back an inch. You don't need to remove the pulley or hoses from the pump.

Apr 08, 2014 | 2006 Pontiac Grand Prix

1 Answer

How do i remove the power steering pump pulley off 2002 pontiac grand prix gt


can rent or buy a power steering pully puller from the parts store it has instructions on how to use and then remove it is also used to install the pully

May 19, 2012 | 2000 Pontiac Grand Prix

1 Answer

How do you take off power steering pump to get to water pump removel one bolt under steering pump


You do not need to remove power steering pump, you can rent a power steering pulley puller tool from most auto parts, just remove the pulley, its much easier and faster, they you can get to that end bolt on the water pump.

Oct 10, 2011 | 2004 Pontiac Grand Prix

1 Answer

Exactly which pulley is my water pump? (1999 pontiac grand prix 3100 sfi v6)??????????????


The power steering pump is dead center on the top of the motor. If your standing on the passenger side the water pump is the next pulley to the right. The serpentine belt will go over the power steering pulley, under the water pump pulley, and then around the a/c compressor.

May 30, 2011 | 1999 Pontiac Grand Prix

2 Answers

I need to find out how to remove the power steering pump on a 2006 pontiac grand prix 3.8L


Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg
*This originally came from abauto

Mar 24, 2011 | 2006 Pontiac Grand Prix

1 Answer

2004 pontiac grand prix, gtp , water pump replacement.. Do you have to remove the fuse box to get access to remove the pump


no, here is procedure according to autozone.com


3.8L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine coolant.
  3. Remove or disconnect the following:

    Negative battery cable. Drive belt Water pump pulley Power steering pump and move it aside Water pump

    0996b43f80208f64.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the water pump assembly mounting-3.8L engine


To install:
  1. Install or connect the following:

    Water pump using a new gasket and torque the long bolts to 25 ft. lbs. (34 Nm) and the short bolts to 16 ft. lbs. (22 Nm) Water pump pulley and torque the bolts to 115 inch lbs. (13 Nm) Power steering pump and torque the bolts to 25 ft. lbs. (34 Nm) Drive belt Negative battery cable
  2. Fill the cooling system.
  3. Start the vehicle and check for leaks, repair if necessary.

Sep 29, 2010 | 2004 Pontiac Grand Prix

1 Answer

Water pump replacement for 2006 grand prix gt supercharged v6


first take the 4 bolts that hold the water pump pulley out, do this while the belt still on, it's easier because the pulley won't turn on you.
remove the pulley then take the 8 bolts around the water pump then pry the pump out.

Feb 26, 2010 | 2006 Pontiac Grand Prix

1 Answer

How do i remove the final bolt from the water pump that is behind the power steering pully? on a grand prix 2002


access 3 power steering pump mounting bolts thru the holes in the pulley, move pump out of the way and install new water ump.

Feb 22, 2010 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
2006 Pontiac Grand Prix Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...