Question about 1999 Oldsmobile Bravada

1 Answer

Air bag removal - 1999 Oldsmobile Bravada

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Which side?

Posted on Sep 07, 2010

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the steering wheel for replacement


SIR DISABLE:
DRIVER SIDE
Many service procedures require the air bag system to be disabled to prevent accidental deployment. The air bag system can maintain sufficient voltage to cause deployment for up to 2 minutes after the ignition switch is turned off, the battery ground cable is disconnected or the DERM fuse is removed. If the inflator module is disconnected from the deployment loop by the following procedure, service can begin immediately without waiting for the 2 minute time period to elapse.
  1. Turn steering wheel so that vehicle wheels are pointed straight ahead.
  2. Turn ignition switch to Lock position and remove key.
  3. Remove air bag fuse from fuse block.
  4. Remove steering column filler panel.
  5. Remove Connector Position Assurance (CPA) and disconnect yellow two-way connector at base of steering column, Fig. 1.
PASSENGER SIDE
  1. Remove air bag fuse from fuse block.
SIR ENABLE:
Driver Side
  1. Turn ignition switch to LOCK and remove key.
  2. Connect yellow two-way connector and install connector position assurance (CPA).
  3. Install steering column filler panel.
  4. Insert air bag fuse into fuse block.
  5. Turn ignition switch to RUN and verify that the air bag warning lamp flashes seven times then turns off.
Passenger Side
  1. Turn ignition switch to LOCK and remove key.
  2. Insert air bag fuse into fuse block.
  3. Turn ignition switch to RUN and verify that the air bag warning lamp flashes seven times then turns off.

remove-steering-wheel-replacement-rfvykuizssn2qn2mhtsbw2yl-3-0.png

Apr 10, 2015 | 1996 Chevrolet K1500

1 Answer

Pcm location 96 passport


old post i do up to 3 months,
with air bags is different than with.
USA answer, LHD , left hand drive, not Right.
no bag, left toe is PCM
yes bags, point finger to radio ,now down past the pocket shelf to store Cassettes or what-nots. bingo PCM and bag brain below
do not fiddly he PCM ever on this bag car, until you read the air bag defeat section in FSM. it can KILL.
here is the quote off the online page.
after key out.


  1. Disconnect the negative and positive battery cables. Wait at least five minutes before working around the Air Bags.
  2. Disarm the Air Bag system. DO NOT SKIP THIS !!!!!
  3. Remove the glove box door and the passenger's Air Bag lower cover.
  4. Disconnect the yellow 2-way Air Bag harness from the passenger's side Air Bag.(the danger point)
  5. Remove the four console screws. Remove the console.
  6. Unscrew and remove the trim panel located below the dashboard cubby hole.
  7. remove the PCM. screws and PCM.

Sep 08, 2013 | 1996 Honda Passport

1 Answer

AIR BAG REMOVAL


Hello: Are you wanting to remove the driver air bag? If so remove the horn pad, that is the drivers air bag, be careful when removing so you don't break the connections for the air bag and horn. You will need a special tool to release the assembly. Tool available at Auto Zone, Advance Auto, or O'Riely.

Jan 10, 2011 | 1997 GMC Sonoma

1 Answer

Need to take off the push part of the steering wheel to get to the horn contacts, already took the two bolts out the back?


First !!! Remove battery terminals and air bag fuse, then insert slot screwdriver in hole next to screws you didn't need to remove and twist to release locking tabs for air bag do the same on other side.Remove air bag remove yellow connector on back of air bag( be careful with air bag ) now you can get at horn contacts.

Feb 28, 2010 | 2001 Chevrolet Silverado

1 Answer

Where is the air bag control module located on a 1997 Saturn


The air bag module is under the center console.Before any repair make sure and disconnect the battery and remove the air bag fuse.Do not remove or disconnect anything in the air bag system for at least a half hr.This system can go off for up to 15 to 20 minutes after power is removed.You also have to watch out for static electricity.This can also make the bags go off.You have to be very careful around air bag systems.Hope this helps.Good luck.

Dec 28, 2009 | 1998 Saturn SL

1 Answer

Needs key cylinder replacement


This first post is WITH AN AIR BAG:



With Air Bag Before removing the steering wheel, disable the air bag system
Disarming the System To disarm the air bag system, simply disconnect the negative battery cable from the battery. Isolate the battery cable by taping up any exposed metal areas of the cable. This will keep the cable from accidentally contacting the battery and causing deployment of the air bag. Allow the system capacitor to discharge for at least 2 minutes, although 10 minutes is recommended, to allow for the dissipation of any residual energy.

CAUTION Before removing the steering wheel, disable the air bag system (refer to Section 6). Failure to do so could result in accidental air bag deployment and possible injury.


  1. Disconnect the negative battery cable and disable the air bag system.
  2. Set the front tires in a straight-ahead position.
c0447ef.gif
Exploded view of the air bag module mounting

  1. Remove the air bag module retaining nuts from behind the steering wheel.
  2. Remove the air bag module.
  3. If equipped, remove the cruise control switch.
  4. Disconnect the horn wiring.
  5. Remove the steering wheel retaining nut.
  6. Scribe a line mark on the steering wheel and steering shaft if there is not one already.
1c64d39.gif
Use a puller to separate the wheel from the column

  1. Remove the steering wheel using a suitable puller.
To install:
  1. To install, align the scribe marks on the steering shaft with the steering wheel.
  2. Ensure the wheel compresses the 2 locktabs on the clockspring.

Oct 11, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Disarm and remove ford expedition air bags


Remove the negative cable from your car battery before replacing car air bags

Deactivate the air bag by removing the air bag fuses. Look in your car owners manual to locate the fuses

Unscrew steering column paneling and remove the airbag bolts on the back side of the steering wheel. Pull out the airbag until you see the back side and unplug the wires

Sep 24, 2009 | 2003 Ford Expedition

1 Answer

How do i remove the air bag on my 2005 vw bettle?


TURN IGNITION SWITCH OFF.MAKE SURE RADIO IS OFF SO YOU WONT LOSE CODE.DISCONNECT NEGATIVE BATTERY CABLE.WAIT AT LEAST 10 MINUTES BEFORE REMOVING AIR BAG.LET THE AIR BAG BATTERY BACK UP POWER. DISCHARGE.BECAREFUL HANDLING AIR BAG. DONT CARRY IT BY IT WIRES.WHEN CARRYING IT.HOLD IN BOTH HANDS SECURLY.WHEN LAYING IT DOWN .BESURE THE BAG AND TRIM COVER FACING UP.BESURE TO KEEP KIDS AND PETS AWAY. BECAUSE AIR BAG CAN STILL BE DEPLOYED.SO BE CAREFUL.

Jun 16, 2009 | 2005 Volkswagen New Beetle Convertible

1 Answer

Airbag deployed


SECTION 501-20B: Occupant Restraints — Passive — Supplemental Air Bag System 2000 Villager Workshop Manual REMOVAL AND INSTALLATION Module —Driver Air Bag Removal
syv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The backup power supply energy must be depleted before any air bag component service is performed. To deplete the backup power supply energy, disconnect the battery ground cable and wait three minutes.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again. If the vehicle was in a frontal collision and the air bag did not deploy, the air bag may not have been needed. Complete a diagnosis of the air bag system before installing a new driver side air bag module (043B13). Refer to Diagnosis and Testing in this section.
  1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
  1. Remove the two driver air bag module retaining bolt access covers (one shown).
  1. Remove the steering wheel bottom cover to access the driver air bag module electrical connector.
  1. Disconnect the driver air bag module electrical connector.
  1. syv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: After removing, discard the driver side air bag module bolts and install new driver air bag module bolts during installation.
    Remove the two driver air bag module retaining bolts (one shown) and discard.
  1. Remove the driver air bag module.
    1. Separate the driver air bag module from the steering wheel and disconnect the horn pad switch.
    1. Remove the driver air bag module.

Apr 16, 2009 | 2000 Nissan Quest

1 Answer

How do you remove or replace the passenger airbag on a 99 contour , Is it a whole dash unit? What holds the drivers bag in the steering wheel? I assumed it was a tork but not sure. Where is the control...


Please rate as fixya if this helps.
the air bag control module is under the console.

  1. Disconnect the battery ground cable.
    1. Wait one minute.
  2. Remove the center console. For additional information, refer to Section 501-12 .
-----------------------------------------------------------------
  1. Disconnect the battery ground cable.
  2. Wait one minute.
  3. NOTE: Contour shown, SVT similar.
    Remove the rear floor console screws.
    1. Move seat fully forward.
  1. Fully apply the parking brake.
  1. Detach the shift indicator selector bezel.
  1. Detach the shift bezel from the selector housing.
    1. Remove three bolts.
    1. Detach shift bezel from the console.
  1. NOTE: The rear floor console must be raised to disengage the front retaining clips.
    Raise and remove the rear floor console.
  1. Remove the four front floor console retaining screws.
  1. Detach the front floor console.
    1. Set the gearshift lever into position 1.
      Partially remove the front floor console.
  1. Disconnect the cigar lighter electrical connections and remove the front center console
-----------------------------------------------------------
  1. Disconnect the air bag control module electrical connectors.
    1. Depress the locking tang.
    1. Slide the locking bar back.
    • Disconnect the connector.
  1. NOTE: The air bag control control module is grounded by the retaining bolts.
    Remove the air bag control module.
    • Remove the three bolts.
--------------------------------------------------------------------------------------------
driver air bag module

  1. Disconnect the battery cables.
  1. Rotate the steering wheel 90 degrees to access and remove the Torx screw. Rotate the steering wheel 180 degrees to access and remove the Torx screws.
  1. Remove the driver air bag module.
    • Disconnect the electrical connector.
    • Remove the air bag module.
------------------------------------------------------------------------------------------
  1. Disconnect the battery cables. For additional information, refer to Section 414-01 .
  1. Open the glove compartment, press the sides inward and lower the glove compartment to the floor.
  1. Remove the passenger air vent duct.
    1. Disconnect the duct from the heater box housing.
    1. Disconnect the duct from the instrument panel register and remove.
29e093f.gif
  1. Disconnect the passenger air bag module electrical connector.
  1. Remove the two retaining bolts securing the rear of the passenger air bag module to the cross-vehicle beam.
14df419.gif
  1. sxp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the passenger air bag module when removing the retaining nuts.
    Remove the two nuts from the front of the passenger air bag module.
4a697c8.gif
  1. Remove the passenger air bag module.
    • Lower the front edge of the passenger air bag module, roll the passenger air bag module around the cross-vehicle beam lowering it into the passenger footwell.
82a0ae0.gif

Mar 15, 2009 | 1999 Ford Contour

Not finding what you are looking for?
1999 Oldsmobile Bravada Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...