Question about 1996 Toyota T100

1 Answer

Replace a slave cylinder? Is it in a housing or easy to get to?step by steps?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 439 Answers

It is fairly simple to get to. It is located outside of the housing usually below the starter with two nuts holding it in. The hard part is bleeding it unless you have a bleeder tool or a friend to push the clutch.

Posted on Sep 07, 2010

Testimonial: "Thanks I'll give it a shot later. "

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bad slave cylinder on 08 jeep patriot


old post.
what engine.?
08 patriot.
why not login to alldata.com and read it, its all there.

excerpts from top 3 online FSM pages.

  1. Remove the transaxle from the vehicle. Refer to Manual Transaxle Assembly, removal & installation.
  2. Disconnect the clutch hydraulic line (6) from the bleeder assembly (2).
  3. Disconnect and remove the bleeder assembly (2) from the clutch slave cylinder (3).
  4. Remove the slave cylinder-to-clutch bell housing bolts (4) and remove the slave cylinder (3) from the transaxle.
so ast step 1, you then turn to that page.
and see
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the splash shields and drain the transaxle fluid.
  3. Disconnect the negative battery cable.
  4. Remove the engine appearance cover.
  5. Remove the air intake assembly.
  6. Unplug the speed sensor connector.
  7. Disconnect the back-up lamp switch.
  8. Remove the shift cables from the bracket clips.
  9. Disconnect the shift selector and crossover cable from the levers. Remove the cables and secure them out of the way.
  10. Remove the slave cylinder hose from the bracket.
  11. Remove the air inlet tube from the throttle body.
  12. Remove the throttle body support bracket.
  13. Remove the upper bell housing bolts.
  14. Remove the starter mounting bolts and secure the starter out of the way.
  15. Support the transaxle with a suitable jack.
  16. Loosen the left-upper transaxle mount through-bolt.
  17. Remove the transaxle mount
  18. Before servicing the vehicle, refer to the Precautions Section.
  19. bolts.
for total of 35 steps.
RTM

Feb 04, 2014 | Jeep Patriot Cars & Trucks

6 Answers

SAAB manual gearbox fluid check & fill location


http://en.allexperts.com

http://www.ptdoityourself.net/tl/tl_indexmain.html

above links will help u get step by step information to solve all problems regarding almost all the cars .

feel free 4 further assistance .rate the particular experts solution as fixya that helps u understand n solve ur problem

Jun 26, 2008 | 1995 Saab 900

1 Answer

Replace slave cylinder 1983 ranger 4x4


The master and slave should always be replaced as one piece.
The slave is mounted on the outside of the ****** next to the bell housing on the drivers side and is easy to replace just get under there and look at it. To bleed it you will need a vacuum clutch bleeding tool like Mityvac makes.
10_10_2012_6_34_23_pm.jpg

Oct 10, 2012 | Cars & Trucks

1 Answer

How to change slave cylinder on f 250 2008


easy job, its located on the bell housing (it actuates the clutch lever to throwout bearing inside transmission). 1. Remove hydraulic line 2.remove mounting bolts. 3.slide slave cylinder out of bellhousing 4. installation is reverse or removal. 5. bleed air out of slave cylinder

Mar 14, 2012 | Cars & Trucks

4 Answers

Can't shift the gear


Is there fluid in the reservoirs? Did it leak out? Where? You can bleed the line just like your brakes and get the pedal pumping again. As long as there are no leaks, The bleeder screw is on the slave cylinder. Hope this helps.

Jul 22, 2010 | 1986 Toyota Celica

1 Answer

I have a 93 Jeep wrangler the slave cylinder went out I need step by step instructions on how to replace it please make the instructions idiot proof


u have to pull trans back or out to do this,,if u want step by step,,get a haynes repair book on ur jeep;;auto zone or advance sell them,,about twenty dollars,,it is not a easy fix,,

May 24, 2010 | 1993 Jeep Wrangler

3 Answers

What is a slave cylinder? and how do i replace it?


The clutch slave cylinder what hydraulicly releases the clutch. It works on the same principal as a brake wheel cylinder. To replace it you unbolt it and bolt on a new one, then bleed it like you do brakes.

Mar 28, 2010 | 1994 GMC Sierra

1 Answer

How do you replace the slave cylinder


Step 1
Raise the vehicle and support with jack stand placed underneath the frame.
  • Step 2 Remove the cover from the reservoir on top of the clutch master cylinder. It will be located in the engine bay on the driver side of the firewall, near the brake master cylinder. Fill the reservoir with DOT 3 brake fluid. Do not allow the reservoir to run dry at any time during the bleeding process.
  • Step 3 Locate the clutch slave cylinder. It will be bolted to the clutch housing. Locate the small bleeder screw near where the hydraulic hose connects to the slave cylinder.
  • Step 4 Connect a length of clear plastic tube to the bleeder screw.
  • Step 5 Open the slave cylinder bleeder screw, by turning it counterclockwise. Have an assistant pump the clutch pedal until clean brake fluid seeps out of the bleeder screw. Then close the bleeder screw. Make sure the clutch master cylinder does not run dry.
  • Step 6 Have the assistant pump the clutch pedal a few times and hold it against the floor. While the pedal is held against the floor, open the bleeder screw and allow the some fluid to seep out. Close the bleeder screw before releasing the clutch pedal.
  • Step 7 Repeat the process listed in the step above and watch the fluid seeping out of the slave cylinder. The clutch is fully bled when there are no more air bubbles in the fluid seeping out of the slave cylinder. You will be able to see the bubbles in the clear plastic tubing. Do not allow the clutch master cylinder to run dry at any point.
  • Step 8 Lower the vehicle.
  • dont forgate to rate
  • Mar 02, 2010 | 1999 Isuzu Rodeo

    1 Answer

    Steps on bleeding a clutch slave cylinder for a 1985 chevy Suburban


    1.) fill resovior 2.) remove bolts connecting the slave cylinder to the bell housing, and remove slave cylinder (leave the line connected if possible)- if not remove line and then reconnect once slave is removed from bell housing. 3.) open bleeder valve on slave, if fluid starts to run out then let it run for 8 to 10 min (all the while keeping an eye on the resovior fluid level, making sure it stays relitivly full.) 4.) close bleeder valve. 5.) top off resovior. 6.) hold slave cylinder in hand, in some way that you can actuate the plunger rod, open the bleeder valve and depress the rod untill it stops, while holding pressure on rod close the bleeder valve. 7.) release the plunger rod. 8.) repeat steps 6. & 7. untill fluid running out of bleeder valve is a steady streem with no air bubbles. (check resovior appr. every 2nd time to ensure it dose not go dry. 9.)re-install slave cylinder and resovoir cap.

    Oct 14, 2009 | 1985 Chevrolet Suburban

    1 Answer

    Hydraulic clutch slave cylinder leaks needs replacement


    you sure can replace it. I suggest checking out autozone.com for a free online repair manual with step by step directions and diagrams

    Mar 31, 2009 | 1986 Ford F 250

    Not finding what you are looking for?
    1996 Toyota T100 Logo

    Related Topics:

    92 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    78267 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8836 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...