Question about 1993 Jeep Grand Cherokee

3 Answers

Whitch pully do you have to loosen to get the belt on?

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 182 Answers

It has a tension er on it pull on the belt and watch which pulley moves that is the tension er. you can put a socket on it or a 1/2 inch or 3/8 inch ratchet on it

Posted on Sep 07, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 439 Answers

You dont loosen any pulleys, there is a tensioned pulley that you can apply tension to, which will allow you to put the belt on. Normally on an arm where all the other ones will be directly attached to the motor or the component it is used to run.

Posted on Sep 07, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 327 Answers

You need to post what engine you have but if you have a 4.0 its the power steering pump to loosen

Posted on Sep 07, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 958 Answers

SOURCE: serpentine belt replacement

you can loosen also the nut at the center of the pully. this nut holds the pulley tight. the long bolt that pulls the clamp is just the tensioner but what holds the pulley is the nut at it's center.

cheers,,


drcool

Posted on Aug 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i get the A/C belt off of my 1996 caravan


If it is a 3.0 engine, you should have an idler pulley you have to loosen to remove the belt. You loosen the bolt in the pulley then turn the adjusting bolt.

Jan 18, 2013 | 1996 Dodge Caravan

1 Answer

How to replace an alternato belt on a 2000 pontic grand am is it the sameas most others ? loosen the pullys and put belt on and tighten back up leaving the belt a little loose?


There should be a automatic tesnioner IF you are talking about a Pontiac? the belt should never be "loose". no pullies to loosen. A 95 Protege, yes you have to loosen and tighten the alternator, the adj bolts are tough to get at.

Aug 03, 2011 | 1995 Mazda Protege

1 Answer

Is the tensioner pulley reverse threaded on a 2001 pontiac Bonneville?


See which way the belt moves on the pully. If it goes right. the bolt will loosen left. If it goes left, the bolt will loosen right. The idea is that the belt moves to the "tight" direction so it doesnt loosen the pully.

Mar 01, 2011 | 2001 Pontiac Bonneville

1 Answer

How to loosen belt on 2005 Camry 4 cyl in order to replace alternator


tensioner pully locate it ... it will have a usually 3/4 bolt on the middle of pully once you get the socket on it apply pressure .. the pully will then tilt to loosen the belt

Feb 06, 2011 | Toyota Camry Cars & Trucks

1 Answer

How do you loosen the serpitine belt on a 2005 chrysler pacifica


Look for the pully that has a spring like housing. Use a wrench (five eights I think) on the pully and it will loosen the belt. Try both ways to find out which way loosens it. This is called the Tension pulley

Dec 09, 2009 | 2005 Chrysler Pacifica

1 Answer

Where do I loosen my belt that is runs A/C on 2000 Toyota Sienna?


One of those "wheels" or TENSIONER PULLYS on your vehicle is the tensioner for the a/c compressor. You will need to look at it and see if there is an adjustment bolt behind pully. If there is, loosen center pully nut, then run adjustment bolt out to slack out the belt. Replace belt and reverse prosedure. DO NOT OVERTIGHTEN BELT,as you can damage pullys and or belt. Tighten to factory specs. Rule of thumb is pulling the belt out and check for slack. No more/less than one inch slack.

Jul 23, 2009 | 2000 Toyota Sienna

1 Answer

HOW TO CHANGE A/C COMP. BELT ON HYUNDAI XG 350


loosen tentioner pully belt... using a 14 mm wrench, release tension on the belt by loosening the 14mm bolt. when loose enough, remove belt.. then install NEW belt.. adjust tension on new belt then tighten 14mm bolt on tensioner pully... you're done.

Jul 16, 2009 | 2002 Hyundai XG350

2 Answers

How do you adjust tension for drive belt


first you need to figure out if you have an automatic tensioner or an adjustable one. so look at the pullies which ones are not accesories (ie not an alternator pully, power steering.) some pullies will just be on there own not driving anything. is this pully connected to something like this O>o <--this end is the pully.
pully mounting bolt ^ ^arm with hole for rachet
or does it look like the pully is attached to a threaded pole.

the auto adjuster need a rachet to pull back on it (because it's spring loaded) while you install the new belt.

the other need the nut on the pully loosened and the threaded pole loosened will move the pully removing tension from the belt (opposite will tension the new belt).

tighten belt until you can only twist it in half.

Jun 25, 2009 | 2003 Toyota Camry

1 Answer

Replace serpentine belt in 1996 Grand AM


One belt to replace, get the correct belt and wrap around all pullys, smooth pullys get smooth side of belt and rigid pullys get rigid side of belt, loosen altenator for removal and remounting then moove back to position and tighten.

Jun 13, 2009 | 1996 Pontiac Grand Am

1 Answer

Belt replacement 1990 acura integra


Ok, you will need a 10 mm socket and extension and a 14 and 15 mm wrench. One of the "idler" pullies is actualy an adjustable tension pully. loosen the center nut on the pully, and then begin loosening the 10 mm bolt from above. as you loosen it, the pully will drop, and soon enough you can slip the belt off.
good luck

Dec 14, 2008 | 1990 Acura Integra Hatchback

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...