Question about 2001 GMC Sierra 1500HD

Open Question

How to replace the ignition switch on a 1980 gmc sierra grande

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: 1997 GMC Sierra Truck Ignition Switch

its a long process,you need a steering wheel puller, once its off take the hazard button assembly out, take the turn signal loose, pull old ignition out, carefully install new one, and reverse procedure and always if u get confused i would highly recomend
a chiltons manual they explain things great

Posted on Feb 16, 2009

  • 59 Answers

SOURCE: 1997 GMC Sierra Ignition Switch Replacement

take off the cover on the top and bottom of the steering column just behind the wheel. pop the tilt lever out simply just by grabbing it and give it a good tug. then once you have the new switch and you get in there your going to need an inverted torx socket to remove the small bolts that hold the switch to the column. do not move the gear on the new switch make sure it lines up exactly as the old one did!!!!!!!!!!!!

Posted on Mar 15, 2009

goalie39
  • 469 Answers

SOURCE: how to replace an ignition lock switch on a 98 gmc sierra

Disconnect the battery on the truck.

Posted on May 09, 2009

  • 523 Answers

SOURCE: replace neutral safety switch on a 1988 gmc sierra

Typically the Neutral Safety Switches are located with the gear selector, either in the column or the floor.

Hope this helps,
Tom

Posted on Aug 21, 2009

  • 82 Answers

SOURCE: how do i change the ignition key switch in my 1988

if your key won't work ,the steering wheel has to come off to replace key switch - special tools needed - if the problem is engine not starting or cranking over - the electric switch the key rod goes down to is on the bottom of the steering column above brake pedal

Posted on Sep 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help me reinstall ignition on 2007 gmc sierra hd sle!


Get a manual from an auto parts store specific for your vehicle. In it, you'll find exploded parts diagrams and step by step instructions on how to replace those parts

Apr 15, 2017 | 2007 GMC Sierra 2500HD

1 Answer

Looking for ignition switch in 93 gmc sierra


Tword the bottom of the steering colume. It will have a couple of connectors going to it and a couple of rods going to it from the igniton cylinder. IT is on top and not easy to get the bolts out of it. You will need to remove the close out pannel to even be able to see it.

Oct 20, 2009 | 1993 GMC Sierra K1500

1 Answer

How to replace ignition key in 1997 gmc sierra 2500,,tack and speedo don't work but all other gauges work


for the ignition key you have to take off the two plastic covers on the steering column. (three torx screws) remove the ignition switch and it is righ there. your speedometer has a direct cable into the transmission and should be a fairly easy repair

Sep 17, 2009 | 1997 GMC Sierra

3 Answers

2002 gmc sierra wont start without useing jumper


Yes it has a rubber cover over it in the engine compartment.i would change the relay.good luck.

Aug 01, 2009 | 2002 GMC Sierra

2 Answers

How to replace an ignition lock switch on a 98 gmc sierra


disconnect battery positive and negative to prevent air bag deployment

May 09, 2009 | 1998 GMC Sierra

1 Answer

1997 GMC Sierra Truck Ignition Switch


its a long process,you need a steering wheel puller, once its off take the hazard button assembly out, take the turn signal loose, pull old ignition out, carefully install new one, and reverse procedure and always if u get confused i would highly recomend
a chiltons manual they explain things great

Feb 16, 2009 | 2000 GMC New Sierra 1500

1 Answer

1997 GMC Sierra Ignition Switch Replacement


take off the cover on the top and bottom of the steering column just behind the wheel. pop the tilt lever out simply just by grabbing it and give it a good tug. then once you have the new switch and you get in there your going to need an inverted torx socket to remove the small bolts that hold the switch to the column. do not move the gear on the new switch make sure it lines up exactly as the old one did!!!!!!!!!!!!

Feb 16, 2009 | 1997 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...