Question about 2000 Daewoo Nubira

1 Answer

No fuel from tank to engine - 2000 Daewoo Nubira

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

Either a clogged line,fuel filter or fuel pump. I would remove line before fuel filter, then the line after fuel filter. if fuel is at all places I checked then right at the engine, if fuel is there then my be injector or ports. Hope this helped Tim

Posted on Sep 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

What does code PO453 mean


the evaporative emission system (EVAP) control system pressure sensor has sent high voltage to the ecm or engine control module and triggered this code either the purge valve located under the car by the gas tank has gone bad, or the charcoal canister has become gas soaked and is pressurizing from gas fumes, or the sensor or wires have shorted , there is also a secondary valve located und the cover of the intake that should also be checked for shorts that can trigger this code but usually it is the one under the car that goes out 9 out of 10 times it is from fuel being burped into the evap canister or charcoal canister from the gas tank which is caused from overfilling the tank or mid day heat of 90 or better with a full tank

Aug 30, 2014 | 2005 Cadillac CTS

1 Answer

Fuel in water


Mr. Harris, My advise is to drain the water and fuel mixture from your fuel tank,remove if is easy the fuel tank and completely dry it up,Go by the engine bay and find the fuel pipe which is coming from the tank to the injection system where probably is a fuel filter,renew the fuel filter, blow air in the pipe from the engine side towards the fuel tank-but before you do blow air in the pipe be sure is not connected to the fuel tank,for not sending the water back in. If you did not start the car since water went into fuel,means that you finished with the above,by connecting everything and put fuel in the tank and start the engine. If you did have the engine running when water went into fuel,means that you have to remove the spark plugs and whilst are out and the fuel tank is clean with new fuel and fuel filter make the engine spinning second to second for 2-3 minutes so as the any old fuel to push out from the spark plug holes. After clean your spark plugs or renew them and also before running the engine is good to put an injection cleaner additive in the fuel tank. Better to put fuel up to a quarter of the tank and run it treating all the system.

Apr 03, 2014 | Ford F-350 Super Duty Cars & Trucks

1 Answer

Not sent fuel from left side of tank to right side on my C203 270CDI


If you have two tanks then you may have two fuel pumps
& one quite,check that out,learn what your vehicle has

One or two pumps
Maybe a switch & solenoid

Nov 15, 2012 | Cars & Trucks

1 Answer

How to put hi pressure fuel pump into the engine,it does not have any mark on the pump rotor?


prev.gif next.gif Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Jul 15, 2010 | 2004 Chevrolet Blazer

1 Answer

How to Change a Fuel Pump on an 2005 Envoy XLT? Must drop the tank? Does it have access under the rear seat?


Usually there is no access under the rear seat for safety reasons.prev.gif next.gif Fuel Tank Removal & Installation 2002-2004 To Remove:
  1. Relieve the pressure in the fuel system.
  2. Lift the vehicle.
  3. Remove the frame brace from the frame.
  4. Remove the fuel tank shield from the fuel tank.
  5. Drain the fuel from the tank into an approved container.
  6. Loosen the fuel hose clamp and disconnect the hose from the fuel tank.
  7. Disconnect the evaporative emission (EVAP) vent valve and fuel tank pressure sensor connectors. Evaporative emission cansister pipes removal and installation gm-05-00-1546.gif

  8. Disconnect the evaporative emission (EVAP) vapor and vent valve pipes from the evaporative emission (EVAP) canister.
  9. Disconnect the fuel return and feed pipes from the fuel tank.
  10. To avoid system contamination, cap the evaporative emission (EVAP) and fuel pipes.
  11. Use a jack to support the fuel tank. Fuel tank removal and installation gm-05-00-1547.gif

  12. Detach the fuel tank straps from the frame.
  13. Lower the fuel tank.
  14. Disconnect the fuel sender connector.
  15. Remove the fuel tank from the vehicle.
To Install:
  1. Place the fuel tank under the vehicle.
  2. Connect the fuel sender connector.
  3. Attach the fuel tank straps to the frame. Torque the bolts to 24 ft-lb (32 Nm).
  4. Remove the caps from the evaporative emission (EVAP) and fuel pipes.
  5. Connect the evaporative emission (EVAP) vapor and vent valve pipes to the evaporative emission (EVAP) canister.
  6. Connect the evaporative emission (EVAP) vent valve and fuel tank pressure sensor connectors.
  7. Connect the fuel hose to the fuel tank. Torque the clamp to 22 in-lb (2.5 Nm).
  8. Connect the fuel return and feed pipes to the fuel tank.
  9. Lower the vehicle.
  10. Refill the fuel tank.
  11. Turn on the ignition for 2 seconds, with the engine off, and then turn off the ignition. After 10 seconds, turn the ignition back on with the engine off.
  12. Lift the vehicle.
  13. Check for leaks in the fuel lines.
  14. Install the fuel tank shield onto the fuel tank.
  15. Install the frame brace onto the frame.
  16. Lower the vehicle.
2005-2007 To Remove:
  1. Relieve the pressure in the fuel system.
  2. Lift the vehicle.
  3. Remove the frame brace from the frame.
  4. Remove the fuel tank shield from the fuel tank.
  5. Drain the fuel from the tank into an approved container. Evaporative emission cansister pipes removal and installation gm-05-00-1544.gif

  6. Disconnect the evaporative emission (EVAP) canister fresh air, solenoid, and purge pipes from the evaporative emission (EVAP) canister.
  7. Disconnect the fuel filler pipe recirculation hose from the fuel tank.
  8. Loosen the fuel fill pipe clamp and disconnect the pipe from the fuel tank.
  9. Disconnect the fuel feed and evaporative emission (EVAP) pipes from the fuel tank.
  10. To avoid system contamination, cap the pipes.
  11. Use a jack to support the fuel tank. Fuel tank removal and installation gm-05-00-1545.gif

  12. Detach the fuel tank straps from the frame.
  13. Lower the fuel tank.
  14. Disconnect the evaporative emission (EVAP) vent valve, fuel tank pressure sensor, and fuel sender connectors.
  15. Remove the fuel tank from the vehicle.
To Install:
  1. Place the fuel tank under the vehicle.
  2. Connect the evaporative emission (EVAP) vent valve, fuel tank pressure sensor, and fuel sender connectors.
  3. Lift the fuel tank.
  4. Attach the fuel tank straps to the frame. Torque the screws to 24 ft-lb (32 Nm).
  5. Remove the caps from the pipes.
  6. Connect the fuel feed and evaporative emission (EVAP) pipes to the fuel tank.
  7. Connect the fuel fill pipe to the fuel tank. Torque the clamp to 22 in-lb (2.5 Nm).
  8. Connect the fuel filler pipe recirculation hose to the fuel tank.
  9. Connect the evaporative emission (EVAP) canister fresh air, solenoid, and purge pipes to the evaporative emission (EVAP) canister.
  10. Lower the vehicle.
  11. Refill the fuel tank.
  12. Turn on the ignition for 2 seconds, with the engine off, and then turn off the ignition. After 10 seconds, turn the ignition back on with the engine off.
  13. Lift the vehicle.
  14. Check for leaks in the fuel lines.
  15. Install the fuel tank shield onto the fuel tank.
  16. Install the frame brace onto the frame.
  17. Lower the vehicle.

Jul 11, 2010 | 2005 GMC Envoy Xl

3 Answers

How to drain ford fusion fuel tank


The "MOST EFFECTIVE
" way is to REMOVE The FUEL TANK and DRAIN it By Tipping it over to Pour From FUEL INLET HOSE. Im Sure you Dont want to Here this as it Requires Much WORK . , BUT It IS The MOST EFFECTIVE Way to EMPTY The TANK.

Oct 31, 2009 | 2004 Ford Fusion

3 Answers

Unleaded Fuel in a Diesel Engine


You can buy a suction hose small enought to get intothe tank at an auto parts store. you will have to remove the fuel from the tank. All of it and then replace fuel filter.

Sep 21, 2009 | 2003 Isuzu Rodeo

2 Answers

When I switch from my front fuel tank to my rear tank gas stops


There is no selector valve on a 1995 ford f150 300 engine. The selector switch on the dash sends power to the pump in the selected tank. The pump then sends fuel to the engine. If engine won't run on the selected switch, the pump in that tank needs replaced.

Mar 28, 2009 | 1995 Ford F150 Styleside Regular Cab

Not finding what you are looking for?
2000 Daewoo Nubira Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...