Question about 1986 Chevrolet Corvette

Open Question

How to remove fuel injector on 1986 corvette - 1986 Chevrolet Corvette

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1986 corvette no spark no injector pulse. already replaced distributor, computer.was runnung at exprway speed, engine shut off...

check that the cam shaft is turning as it may be a broken timing belt that is causing your grief. Always run fault codes before wasting money on replacing perfectly good items.

Aug 31, 2014 | 1986 Chevrolet Corvette

1 Answer

I have a 1986 monte carlo with a 1990 corvette engine when starting cold it will stall after just a few seconds. i can get it to stay running by reving it high for 15 to 20 seconds but i have alot of...

i would check the fuel injectors to see if 1 of them isn't bad, i had a 1989 corvette with a L98 engine, and it would start up, run a few seconds , then die, then , when i would try to re start it . sometimes it would, and sometimes it wouldn't, i would have to let it set for a short while, but after i diagnosed the fuel injectors , i found out that the # 6 injector on my engine , was bad, i replaced it, and it ran fine aftewards, also , you can check the throttle positioning sensor, hope that this information has helped you.

Apr 03, 2011 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

I smell gas after my car warms up and then it dont want to start right up like its flooding the tell pipes are turning black like there is to much gas sorry this is a 1986 corvette new engine fuel system...

you are correct it is a fuel problem/getting to much fuel,if its carborated i would try to adjust it to lean it out a bit.if its fuel injected i would try to get smaller injectors or reduce the fuel pressure.

Oct 26, 2010 | 1986 Chevrolet Corvette

1 Answer

How to replace fuel pump on 1986 corvette

remove fuel door, rubber boot, take out bolts from sender,pull up sender from tank,replace pump and screen on the end.replace pretty easy on vette.

Jun 19, 2010 | 1986 Chevrolet Corvette

1 Answer

How do I replace a fuel injector in a 1986 jeep Cherokee 2.5liter

1.) Remove air inlet elbow and hose.
2.) Remove injector wiring connector and injector retainer clip.
3.) Using small pliers, carefully grasp center collar of injector between electrical terminals and carefully remove injector with lifting-twisting motion. Discard both "O" rings.

To iInstall
Using light oil, lubricate new upper and lower "O" rings. Install them in housing bore. Install back-up ring over upper "O" ring. Position replacement injector in fuel body. Center nozzle in lower housing bore. Use pushing-twisting motion to seat injector. Align wire connectors in proper orientation. Install retainer clip and screws. Connect injector wiring. Install air cleaner.

Apr 06, 2010 | 1986 Jeep Cherokee

1 Answer

How to replace a fuel pump on a 1986 chevy corvette

fuel pump is in fuel tank remove tand and take pump out of top of tank were hoses and fuelguage sensor hooks up

Nov 11, 2009 | 1986 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides