Question about 2000 Chrysler Sebring

Open Question

Intake manifold upper and lower torque specs and sequence?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
chargerhp
  • 814 Answers

SOURCE: i am replacing the intake gasket on my 2005

If you are looking at the engine from the front and the large hose is at the bottom right the tightening sequence is from upper left to right 6237 bottom left to right 5148 just like I typed it torque is 250 inch pounds on lower intake and 105 inch pounds on the upper intake. So when you look at those numbers you tighten 12345678 in that order to 250 inch pounds in 3 increments then install the top intake.

Posted on Feb 25, 2010

Ad
ZJLimited
  • 17970 Answers

SOURCE: need the torque specs for

4022caa.jpg

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Posted on Oct 11, 2010

SOURCE: WHAT ARE THE TORQUE SPECS FOR THE INTAKE MANIFOLD

Sorry first attempt got sent by accident

Upper intake manifold bolts/nuts 168 in-lbs

Lower intake manifold nuts are done in 4 steps

Step1. Front nuts 61 in-lbs
Step2. Rear nuts 185 in-lbs
Step3. Front nuts 185 in-lbs
Step4. Repeat Steps 2 and 3

Posted on Feb 23, 2011

johnjnail
  • 1702 Answers

SOURCE: torque specs for upper and

intake manifold upper and lower 89 in. lbs.

valve cover 89 in. lbs.

Posted on May 20, 2011

  • 202 Answers

SOURCE: need torgue specs & sequence for upper & lower

Lower: Torque to 28 N·m (250 in. lbs.)

Upper: Torque to 12 N·m (105 in. lbs.)

Sequences below:

mf_grimm_1.jpg

mf_grimm_2.jpg

Good luck.

Posted on Jul 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intake manifold sequence and torque specs ford 500 2006


Engine code vin 1, 3.0L ,My info says 89 in lbs, upper and lower, notice that said inch lbs not ft lbs.
The picture should be for lower intake manifold. Sorry, my free-hand drawing isn't very good. Make sure correct vin? Hope you can read it.
intake manifold-a1g5guitqnudv1dyisqw2gc4-3-0.jpg

Aug 27, 2017 | Ford Cars & Trucks

1 Answer

3.5L oldsmobile intrigue intake manifold sequence and spec torque


The torque specification is a 2-step process;

Tighten the vertical lower intake manifold bolts (the four middle ones) to 7 Nm (62 lb in). Tighten the diagonal lower intake manifold bolts (two on each end) to7 Nm (62 lb in). Tighten the vertical lower intake manifold bolts (the four middle ones) to 13 Nm (115 lb in). Tighten the diagonal lower intake manifold bolts (two on each end) to 25 Nm (18 lb ft).


2009-05-15_194459_lower.gif

Oct 11, 2013 | Cars & Trucks

1 Answer

What are the torque spec for upper and lower inntake manifold


the 3.8 liter lower intake bolts should be tightened to 11 ft-lbs in sequence.

the upper for the same engine is 89 inch-pounds, again in sequence.

Feb 14, 2012 | Cars & Trucks

1 Answer

Need torgue specs & sequence for upper & lower


Lower: Torque to 28 N·m (250 in. lbs.)

Upper: Torque to 12 N·m (105 in. lbs.)

Sequences below:

mf_grimm_1.jpg

mf_grimm_2.jpg

Good luck.

Jul 23, 2011 | 2004 Dodge Intrepid

1 Answer

Need the torque specs for the upper intake bults on a 2002 chrysler sebring conv. 2.7L


4022caa.jpg

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Oct 11, 2010 | 2002 Chrysler Sebring

1 Answer

Intake manifold torque specs and sequence 1998 malibu 3.1 litre


8ef3de6.jpg

Fig. Exploded view of the upper and lower intake manifold and fasteners

- Position the rocker arms in their original locations and tighten to the proper specifications.

- Install lower the intake manifold attaching bolts. Apply sealant or equivalent thread locking compound to the threads of bolts. Tighten the vertical bolts first, then the diagonal bolts to 115 inch lbs. (13 Nm).

- Install the upper intake manifold and tighten the mounting bolts to 18 ft. lbs. (25 Nm).

Hope helps (remember to rate this).

Oct 05, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

Looking for torque specs and sequence of both intake manifold and plastic plenum on 98 pontiac bonneville 3.8 non turbo


Lower intake bolts 11 ft. lbs start in the center of the intake and work your way out cross from side to side.Tighten the upper intake bolts with the same procedure with 89 inch pds.Be sure to apply threadlocker to the lower intake bolt threads.

Feb 07, 2010 | 1998 Pontiac Bonneville

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

Not finding what you are looking for?
2000 Chrysler Sebring Logo

Related Topics:

1,007 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...