Question about 2001 Lexus RX 300

1 Answer

Bulb is good but headlight is still - 2001 Lexus RX 300

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 182 Answers

Check the headlight fuse

Posted on Sep 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The right headlight for my 1999 ce corolla is not working but the side light is working and the full light is work


HEAD LIGHT BULB COULD BE BLOWED.REPLACE HEADLIGHT BULB STILL DONT WORK USE A 12 VOLT TESTLIGHT CHECK TO SEE IF HEADLIGHT BULB SOCKET GETTING POWER WITH LIGHT SWITCH ON POSITION HOOK TEST LIGHT WIRE TO A GOOD GROUND THEN PROBE POSITIVE SIDE OF HEADLIGHT BULB SOCKET.IF TEST LIGHT COME ON THEN MORE LIKELY BULB SOCKET WORN OUT NOT GETTING GOOD GROUND CONTACT INSIDE SOCKET OR GROUND WIRE LOOSE BROKEN.

Oct 31, 2010 | Toyota Corolla Cars & Trucks

2 Answers

How to change the headlight bulb


Open the hood. Look at top corners of headlight assy, and you will notice two metal "L" shaped holders. Rotate these forward out of their plastic mounts. Pull both up and completely out. With a little side ways jiggling you can now remove the entire headlight assy. Turn the bulb holder clockwise to remove. Gently pry the holding clip to release bulb holder and bulb {they are one piece) from wiring connector. Install new bulb in reverse order. Tip: clean new bulb with rubbing alcohol before installing into headlight housing, because oil from fingers will greatly reduce bulb life. Also many auto part stores will install for free if you buy the bulb from them.

Apr 19, 2010 | 2005 Chevrolet Tahoe

1 Answer

How do I replace a headlight bulb in my 1996 Olds achieva


How to Replace a Headlight Bulb
(DIY Complexity: Easy / Time: 0.9 hour)

Parts:
1. Headlight Bulb

Tools:
1. Screwdriver
2. 1/4 in. Drive Ratchet
3. Socket Set

0fc6099.jpg

HIGH PERFORMANCE HALOGEN HEADLIGHT BULB -- Low 45/high 65 watts, Dual C-8 filament for both high beam and low beam; 100 percent legal halogen headlight bulbs; Features the whitest and brightest light color similar to daylight for safer night driving; Meets all US FMVSS 108 and Canadian CMVSS 108 requirements.

Steps:
Step 1 Open the hood and locate the headlight assembly.
o Tip: Most headlight assemblies have a place in the rear to gain access to the headlight bulb.
o Tip: It is recommended that headlight bulbs are replaced in pairs.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Gain access to headlight bulb.
o Tip: It is a good idea to check the high beam and low beam headlight bulbs at this time.

Step 3 Disconnect the wiring harness and replace the old headlight bulb with a new one.

35e674e.jpg

Remove the retaining ring from the base of the bulb, then...


99dfc4e.jpg

...turn the bulb and remove it from the headlight assembly.

Step 4 Turn on the headlights and check high and low beams to verify repairs.


Hope this help (remember comment and rated this).

Mar 30, 2010 | 1996 Oldsmobile Achieva

1 Answer

Need to replace headlight bulb 2007 hhr


H13 HALOGEN HEADLIGHT BULB, SOLD INDIVIDUALLY -- Low 55/high 65-watt halogen bulb; 12.8 volts; P26.4t base; A high quality, direct fit OE replacement headlight bulb

3c8c3dc.jpg


How to Replace a Headlight Bulb
(DIY Complexity: Easy / Time: 0.9 hour)

Parts:
1. Headlight Bulb

Tools:
1. Screwdriver
2. 1/4 in. Drive Ratchet
3. Socket Set

Steps:
Step 1 Open the hood and locate the headlight assembly.
o Tip: Most headlight assemblies have a place in the rear to gain access to the headlight bulb.
o Tip: It is recommended that headlight bulbs are replaced in pairs.
o Tip: Always make sure the struts on the hood can fully support the weight of the hood so that it does not close on you while working. The use of a hood prop can securely hold it in place.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Gain access to headlight bulb.
o Tip: It is a good idea to check the high beam and low beam headlight bulbs at this time.

Step 3 Disconnect the wiring harness and replace the old headlight bulb with a new one.

Step 4 Turn on the headlights and check high and low beams to verify repairs.

Hope this help (remember rated this help). Good luck.

Mar 30, 2010 | 2008 Chevrolet Hhr

2 Answers

2001 Mazda MPV headlights do not work at all. The running lights do.What could be the problem?


try replacing both headlight bulbs first. if that doesnt work then you have a wiring issue

Oct 12, 2009 | 2001 Mazda MPV

1 Answer

Headlight low beam


Test to see if you have voltage at the bulb connector in low beam position. I'd almost bet that if there is no voltage there for the low beams that you have a bad high/low switch.

Oct 03, 2009 | 2002 Subaru Forester

1 Answer

2007 Forrester - headlight bulb good but not lighting


You will need to look at the plug for the headlight. If it looks good, I would look for the headlight low beam fuse.

Mar 05, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

1 Answer

Headlights 2001 Dodge Durango


headlight cover does not have to be removed. Open your hood and reach in to the back of the headlight assembly grasp the main headlight plug and pull while turning counter clockwise. the bulb should come out with the plug, the bulb will then unclip from the plug, good luck

Mar 01, 2009 | 2001 Dodge Durango

1 Answer

Driver's side Headlight Bulb Replacement


Do you mean the entire headlight assembly or just the bulb?
If it's the entire headlamp look at the new one to see where the fastening points are, the grill may have to be removed and also the parking lamp lens, if it's just the bulb it's easy Open your hood look at the back of the headlight assembly and twist the bulb holder ring to release it. Good Luck To You

Jan 20, 2009 | 2008 Honda Element

1 Answer

1986 Ford Bronco


I believe u have the sealed beam headlight---remove the screws holding the trim ring around the headlight, being careful NOT to touch the adjusting screws that aim the unit. U want to remove the 4 screws that go into the trim piece that fits around the edge of the headlight, make sure u take a good look w/ a light, to make sure u are removing the screws holding the trim piece. Pull the headlight out, unplug it, replace w/ new one and u r good to go.
If u have the newer style headlight (I'm quite sure '87 and above do, not sure of '86), u have to replace the halogen bulb only. 1st thing to know is to be careful handling this type of bulb. Don't touch the new bulb w/ your hands, wear gloves or hold bulb w/ a clean rag. If u touch it oils from your skin will cause it to overheat and burn out prematurely, and it also contains gas in the bulb and is under high pressure, so dropping or scratching the surface can cause old or new bulb to shatter, wear goggles to be safe. Open hood, locate rear of headlight assembly, unplug electrical connector, rotate bulb retaining ring counterclockwise 1/8 turn (as viewed from the rear), and slide it off the bulb base. Pull bulb straight out, don't twist. To install, bulb goes in flat side up, insert into headlight assembly, u may have to turn it slightly to align the locating tabs,when aligned push bulb firmly into place, 'til bulb contacts the mounting flange in the socket, put retaining ring over bulb base against the mounting flange, rotate clockwise. Snap electrical connector in place. good luck! countrycurt0

Sep 30, 2008 | 1986 Ford Bronco

Not finding what you are looking for?
2001 Lexus RX 300 Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

907 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...