Question about 2006 Chevrolet Colorado

Open Question

How to replace abs sensor in 2006 colorado - 2006 Chevrolet Colorado

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4044 Answers

SOURCE: abs default light is on

You have replaced the Master Cylinder and ABS sensors, That only leaves the calipers and Vacuum line to the master Cylinder. When you replaced the sensors and Master Cylinder I assume you reset the ECM module. If you didn't try resetting the ECM by removing the Negative Terminal for 1 min then reconnect it and see if that ABS light comes back on. If it does then you need to check the Vacuum line on the Master Cylinder and make sure you have Good vacuum. If the Vacuum is good check your Brake Calipers to make sure they aren't malfunctioning.

Posted on Oct 12, 2010

  • 90 Answers

SOURCE: abs light

This is a (4) four wheel sensor system and more than likely one of them has failed. This will cause ABS module to turn on warning lamp and make the brake pedal 'act up' under the right conditions.This 'acting up' is the ABS system getting a false signal that a wheel is not turning the same as the others when it actually is. Have it scanned for codes and a streaming data scan on a road test under the same conditions that you are experiencing the 'act up' to pinpoint the fault. Hope this helps! Please rate me.

Posted on Jan 31, 2009

SOURCE: how do you test abs wheel sensors on 2006

with a scanner driving. all should read the same., yes they are in the hub and need to be replaced as a whole. You could ohm them to see if one is bad but alot of times this is inconclusive. You will have better luck driving and monitoring the sensors.

Posted on Aug 01, 2009

c17hydro
  • 2984 Answers

SOURCE: how do i change out the knock sensor on a 2006 chevy colorado

You didn't list your engine size so please pick the applicable to your motor size:

Removal & Installation 2.8L & 2.9L Engines To Remove:

  1. Lift the vehicle high enough to gain access to the knock sensor (KS) through the left front wheelhouse.
  2. Remove the left front wheel and wheelhouse liner.
Knock sensor (KS) (A), Engine harness (B), Knock sensor (KS) connector (C)


e44e83f.gif
  1. Disconnect the knock sensor (KS) connector.
  2. Detach the knock sensor (KS) from the engine block.
To Install:
  1. Attach the knock sensor (KS) to the engine block.
    • Tighten the bolt to 18 ft lbs (25 Nm).
  2. Connect the knock sensor (KS) connector.
  3. Install the left front wheelhouse liner and wheel.
  4. Fully lower the vehicle.

Posted on Sep 03, 2009

johnjohn2
  • 5763 Answers

SOURCE: who do i replace the rear ABS speed sensor on 2006

i belive theres two ,one on each wheel in the rear, you unplug connector, then remove the bolt holding sensor to backing plate and then remove, two wheel drive vans you need too replace the wheel bearing asm,heres two pictures too show you and then you see which type you have,one is the sensor the wire type the other is the bearing asm, hope this helps,6608e12.jpgdbfde76.jpga7cca55.jpg

Posted on May 15, 2010

Testimonial: "thanks very much... the information helped a great deal."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Chevy colorado 3.5 engine replace speed sensor front wheels


the abs speed sensor is part of the hub, you have to replace the hole hub

Dec 16, 2012 | 2004 Chevrolet Colorado

2 Answers

2006 chevy colorado abs light on changed left speed censor


if you broke sensor wire at the electrical connector.the dealership more likely can get you another sensor connector with new wires splice in new wires and connector.

Nov 12, 2011 | 2006 Chevrolet Colorado

1 Answer

Changed my front brakes and rotors..ABS light came


did you knock off a wire on the sensor ,or even break the sensor unit when you changed the rotors..

Jul 11, 2010 | 2006 Chevrolet Colorado

3 Answers

Abs light is on


try removing the pos. battery cable for 10 seconds then replace it, if you lost fluid fill it up to full line ,or to top, hope to help you, robert b.

Jul 11, 2009 | 2004 Chevrolet Colorado

3 Answers

Replaced front brake pads and rotors now have an abs fault.what are the probable causes and/or remedies...without $$$ at the Dealership!?!?


The gaps on the front ABS sensors could be off. If they cant pick up the rig it will cause a fault. The sencors sould slide back and fouth in the housing. If they move take a reguar sheet of paper fold it in fouths. Then place it between the rig and the sensor. Put the sensor so that there is slight presser on the paper. This will be close to the gap you need.

Jun 30, 2009 | 2006 Chevrolet Colorado

1 Answer

Abs fault light comes on goes off when u reset it,but might come


It sounds like you may have a bad ABS sensor. Best thing to do is check all the wire harness from all the wheels for cracking or breaks. The sensor could also need some adjustment, not sure how it is on the Colorado. There are some ABS sensors that is a part of the wheel hub and just dubble check the wire harness since the hub is going to be replaced = expensive. If it's a ABS sensor that counts the rotation from the wheel hub then it's adjustable. 
The sensor may have moved out a way from the ring counter and may just need to be moved closer to the ring which is a part of the wheel hub. Most of the time a good spray of Brake cleaner will fix that. Just follow the the ABS wire leads to the hub and you should see the sensor. Be surprised on how much dirt can collect back there.
Good luck and hope this helps, If you can get to a auto parts store that will scan for free like Auto Zone. The ECM may even have the information to which wheel has the bad sensor reading. At worst, it's your ABS system it self that may be going bad.

May 22, 2009 | 2005 Chevrolet Colorado

1 Answer

2004 Chev Colorado Z-71 4WD ABS "chatter"


Did you ever find a solution to this problem? My 2004 Colorado just started doing the exact same thing!

I can be reached at garyru21@juno.com

Thanks!

Mar 09, 2009 | 2004 Chevrolet Colorado

1 Answer

Abs light


This is a (4) four wheel sensor system and more than likely one of them has failed. This will cause ABS module to turn on warning lamp and make the brake pedal 'act up' under the right conditions.This 'acting up' is the ABS system getting a false signal that a wheel is not turning the same as the others when it actually is. Have it scanned for codes and a streaming data scan on a road test under the same conditions that you are experiencing the 'act up' to pinpoint the fault. Hope this helps! Please rate me.

Jan 31, 2009 | 2004 Chevrolet Colorado

Not finding what you are looking for?
2006 Chevrolet Colorado Logo

Related Topics:

923 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...