Question about Suzuki Samurai

Open Question

I have a 1986 suzuki samurai 1.3 I am looking for the valve clearance on the intake and the exhaust can you help?

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 674 Answers

SOURCE: valve clearance


i hope this helps good luck
thanks for using FIXYAbc70713.gif

Posted on Aug 26, 2008

  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

  • 1 Answer



Posted on Apr 15, 2009

  • 2 Answers

SOURCE: valve clearance 94 yzf 750

valve clearance for a 1994 yzf 750 is .11-.20 in. intake, and .21-.30 in. exhaust

Posted on Aug 26, 2009

  • 301 Answers

SOURCE: valve clearance on xr200 1993

.002" on the intake, and .003" on the exhaust valves (engine cold).

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Valve clearance on suzuki vitara 1999 1.6

  • Set the engine to Top Dead Centre (TDC) of the compression stroke for the cylinder to be adjusted.
  • Check the valve clearance. The valve clearance specifications are as follows:

    Intake valves: 0.005-0.007 inches (0.13-0.17mm) Exhaust valves: 0.005-0.007 inches (0.13-0.17mm)
  • After adjustment, tighten the lock nuts to 11-14 ft. lbs. (15-19 Nm).
  • Repeat for each valve to be adjusted.
  • Feb 16, 2017 | Suzuki Cars & Trucks

    1 Answer

    Need valve specification on 86 chevy nova

    from my 1985/1986 official shop manual:
    figure 6A1-39 valve stem and guide clearance
    max intake clearance 0.08 mm (0.0031 in)
    max exhaust clearance 0.10 mm (0.0039 in)
    pg 6A1-17 If clearance is greater than the values given in 6A1-39, then replace the valve and guide

    pg 6A1-17
    standard overall length
    intake 106.88 mm (4.2079 in)
    exhaust 106/78 mm (4.2039 in)
    do not grind more than 0.5 mm (0.020 in)

    Mar 11, 2015 | 1986 Chevrolet Nova

    1 Answer

    Pls give me correct tappet valve clearance of intake and exhaust for 4G15 mitsubishi lancer

    Valve clearance Intake 0.20 mm (Hot- at operating temp)
    Valve clearance Exhaust 0.25 mm (Hot).

    Feb 12, 2014 | 1986 Mitsubishi Lancer 1.8

    1 Answer

    1.3 valve clearance suzuki

    1995 samurai. valve lash , right not valve stem to guide clearance.
    there are 3 clearances.
    volume 1
    pdf page 111 tells you this (book page C3-53)
    the manual is everywhere.

    Jan 21, 2014 | 1995 Suzuki Samurai

    2 Answers

    Procedure of tappet adjustment

    make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

    Mar 14, 2010 | 1986 Suzuki Samurai

    1 Answer

    What is the valve clearance and torque setting for headbolts on a suzuki 1.3 sport

    intake- 0.13 - 0 .17 mm
    exhaust- 0.16 - 0.20 mm
    when engine is cold
    head bolts 51 - 54 lb ft

    Feb 26, 2010 | 1994 Suzuki Samurai

    1 Answer

    Valve Clearance

    valve clearance, with engine hot, intake valves are .005-.006 in, exhaust valves are .011 in, if engine is cold then its intake .009-.011 in and exhaust is .007. hope this helps good luck.

    Nov 28, 2009 | 1989 Suzuki Swift

    1 Answer

    Samurai backfire

    It sounds more like a timing problem. If it backfires through the carb that means the intake valve is open when the spark plug fires. Same with the exaust but it the exhaust valve that is open.

    Dec 14, 2008 | 1986 Suzuki Samurai

    1 Answer

    Valve tappet adjustment

    well, I can see ur message has been here for quite some time. Most probably you got the answer to ur request.
    I just did the valve clearance on the engine of my SJ413 that has the 1000cc engine of an SJ410 :
    When cold: 0.13mm Intake and 0.18mm Exhaust
    Engine sounded well and worked fine after that.

    Nov 18, 2008 | 1986 Suzuki Samurai

    1 Answer

    Valve clearance


    i hope this helps good luck
    thanks for using FIXYAbc70713.gif

    Aug 26, 2008 | 1995 Suzuki Samurai

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    101 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Suzuki Experts


    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Boyet Soriano
    Boyet Soriano

    Level 2 Expert

    293 Answers

    Are you a Suzuki Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides