Question about 1985 Ford Bronco

Open Question

Torque specs 1985 ford bronco rear differential

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: rear axle seal replacement 1994 ford bronco

It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Posted on Dec 29, 2008

chuck943
  • 783 Answers

SOURCE: torque specs 7.5 inch rear axle 96 ford ranger

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Posted on Jan 30, 2009

chuck943
  • 783 Answers

SOURCE: torque specs foe 4.9 ford f150 flywheel

75-85 ft lbs

Posted on Mar 04, 2009

  • 207 Answers

SOURCE: Head gasket torque specs

Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.

Posted on Apr 30, 2009

  • 743 Answers

SOURCE: torque specs on Chevy Silverado 2500 rear diff yoke.

There isn't a torque spec since those bearing are pre-loaded. You place the unit on a good known vic and get a breaker bar and you might even have to put an extention on that and you begin to tighten unitil you fell the bearing start to load...a little extra short turn wouldn't hurt at that point.

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1985 Oldsmobile Cutlass salon torque specs on differential bearing cap


You sound like a DIY. So you need a repair manual, You will need it next time anyway. Your auto parts store probably carry it. If not,
try filepeep.com They may have it.
or try manualslib.com

Mar 15, 2015 | 1985 Oldsmobile Cutlass Salon

1 Answer

What is the torque spec for a 1978 Ford pinto differential pinion nut?


170 ft.lbs is the minimum; be aware that this differential uses a crush sleeve to set the backlash and the pinion torque is what crushes the crush sleeve. If you don't set the backlash correctly you can grind up your differential gears.
8 Inch Ford Rear End Torque Specifications eHow

Feb 02, 2015 | Ford Cars & Trucks

1 Answer

Torque specs for 2008 ford ranger 4x2 front axle


Torque Specifications

Description Nm lb-ft Axle-to-frame bolt 66 49 Axle damper-to-frame bolt 34 25 Brake caliper guide pin bolt 33 24 Differential bearing cap bolt 61 45 Differential housing cover bolt 29 21 Ring gear bolt 122 90 Tie-rod nut 91 67 U-joint spider retainer bolt 19 14 Upper ball joint pinch bolt 48 35

Sep 18, 2014 | 2008 Ford Ranger 2WD

1 Answer

Flywheel torque specs for a 1984 ford bronco 2 xlt


if you have an impact wrench set it on 3 and run the bolts down until the impact just starts hammering torque is set

Dec 31, 2011 | 1984 Ford Bronco II

1 Answer

I need the torque specs for my valve covers on my 1990 bronco 2 v-6


No torque specs. Don't use sealer, that can cause the gasket to slip. Put cover in place, start all bolts, loosely snug all, hand tighten from bottom two, top two, bottom ends, top ends. Warm up motor and re-tighten (good hand snug) do not over tighten.

Oct 19, 2010 | 1990 Ford Bronco

1 Answer

What would make the rear antilock brake light stay on in a 1987 ford bronco?


Might possibly be the rear sensor on the top of the rear differential, very very common on those and the fords of that time.

Jul 25, 2010 | 1987 Ford Bronco II

1 Answer

Where does the shift solnoid on a 1985 bronco


on the rear of the transmission there is a metal stem sticking out of the rear

Feb 12, 2010 | 1985 Ford Bronco II

1 Answer

Where is he starter in 1985 ford bronco 2 at


oh i get it, the starter is at the bottom rear of the engine where it mates to the transmission bell housing, u must get under the truck to see it, it is no the drivers side i believe.

Oct 01, 2009 | 1985 Ford Bronco

1 Answer

Torque specs 7.5 inch rear axle 96 ford ranger


Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Jan 30, 2009 | 1996 Ford Ranger SuperCab

1 Answer

Rear axle seal replacement 1994 ford bronco


It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Dec 29, 2008 | 1994 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...