Question about 2004 Chrysler Sebring

1 Answer

Blower motor working on all 4 speeds but air only circulates through the defrost. No air circulation at floor or top vent outlets.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 8,142 Answers

No vacuum to switch. The system uses vacuum from the intake manifold to operate the various vent doors. Look under the hood for the small vacuum line that goes into the firewall near the A/C lines--there may be some other ones there a different color, but only one--usually black--goes to the intake manifold vacuum port. Make sure it's hooked up and not leaking there. If that's OK, see if you can get behind the control switch in the cabin. The line may have come loose there, or perhaps your switch is leaking there.

Posted on Sep 06, 2010

Testimonial: "Thank you so much for your advice. I will check this out. Again, thank you. Harry"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have no control over the ac/heater blower motor. EATC replaced no effect


Have you replaced the blower motor speed control resistor located next to the blower motor? If no that may be the problem.

Feb 16, 2017 | Mercury Cars & Trucks

1 Answer

Why is fan control stuck on 4?


A mechanical fan/blower control that's stuck on 4 is a worn/faulty switch. The blower motor fuse could be blown or the blower motor is dead. A electronic fan/blower control that's stuck on 4 with no blower could be a blown fuse in your fuse box, the blower motor is dead or the climate control reading itself could be sending a false reading or the unit tself iis faulty.

Sep 18, 2015 | Subaru Impreza Cars & Trucks

2 Answers

What causes a/c to blows cold on driver's side and hot on passenger side ?


There is a little motor on the heater box under the dash that needs to be replaced. It's called a blend door actuator...

Mar 16, 2015 | 2004 Cadillac DeVille DHS

1 Answer

Why is hvac air coming from all three locations (vent/floor/defrost) regardless of switch setting?


Check air box if it won't change air flow some thing is wrong there inside the car

Jul 14, 2014 | 2000 Buick Regal LS

1 Answer

REPLACED BLOWER MOTOR CONTROL MODULE...Now blower is working but not very much air flowing out of vents! Fan speed is working...it heat and cools. but still not adequate air flow from the vents ..2000...


check your blower hoses to see if one or more have come loose or got redirected or the selector switch isn't functioning properly (is it blowing better on defrost as opposed to floor vents, or forward vents, etc.)
Good luck

Oct 26, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Started out with cold air coming out the vents


I'm no 'expert' but it sounds like possibly 2 different problems. Your heat comes from warm/hot coolant circulating through the heater core, and the fan blowing air through/over it. If your thermostat is not opening the coolant won't circulate. Thermostat is a not too difficult or costly starting place. No air flow leads me to think you have a blower motor issue, perhaps start with the fuse. Hope this helps.

Dec 04, 2009 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

Blower motor vent selection switch not working


the hvac selector switch in the dash may be the problem.You need to remove the switch and look at the connector on the back of switch,see if there are any burnt wires at the connector or switch.It's all electronic and the switches have been known to burn out on this and other model.

May 26, 2009 | 1998 Buick LeSabre

2 Answers

2006 Dodge ram-a/c-heater fan works fine,all speeds,low to high-but no matter what speed I turn it to only a little air comes out,heat,defroster,a/c vents etc.


Does your blower have a vibration at higher speeds? Have the same problem in my truck. After digging into it I found that the Re-circulation door axle pivot is broken. This door shuts off the outside air intake for re-circulating air. It also closes off the interior air intake when re-circ isn't used. If the door is broken it will sit in a half open position allowing all the forced air to escape through the outside air intake. I hear this is a common thing to happen. The servo motor that cycles the door is a little too powerful and it snaps the axle pivot.

Mar 17, 2009 | 2006 Dodge Ram 1500

1 Answer

No air flow from defrost vent on my van.


Could be a vaccum line leaking not changing the vent flap to defrost

Jan 10, 2009 | 2001 Oldsmobile Silhouette

Not finding what you are looking for?
2004 Chrysler Sebring Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...